Jandy Pro Series Underwater Pool and Spa White Lights User Manual

OPERATION MANUAL

Jandy Pro Series
Underwater Pool and Spa White Lights

WARNING
FOR YOUR SAFETY – This product must be installed and serviced by a contractor who is licensed and qualified in pool equipment by the jurisdiction in which the product will be installed where such state or local requirements exist. In the event no such state or local requirement exists, the maintainer must be a professional with sufficient experience in pool equipment installation and maintenance so that all of the instructions in this manual can be followed exactly. Before installing this product, read and follow all warning notices and instructions that accompany this product. Failure to follow warning notices and instructions may result in property damage, personal injury, or death. Improper installation and/or operation will void the warranty.

Important Safety Information

IMPORTANT SAFETY INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS READ AND FOLLOW ALL INSTRUCTIONS

When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:
WARNING
RISK OF ELECTRICAL SHOCK OR ELECTROCUTION. This underwater light must be installed by a licensed or certified electrician in accordance with the National Electrical Code® (NEC® ) in the US, the Canadian Electrical Code (CEC® ) in Canada, and applicable local codes and ordinances. Improper installation will create an electrical hazard, which could result in death or serious injury to pool or spa users, installers, or others due to electrical shock, and may also cause damage to property. Read and follow the specific instructions below.
**WARNING
Before installing this underwater light, read and follow all warning notices and instructions accompanying this light. Failure to follow safety warnings and instructions can result in severe injury, death, or property damage. Call 800-822-7933 for additional free copies of these instructions.
****CAUTION
Except when the Jandy Pool and Spa lights are installed in an area of the swimming pool that is not used for swimming and the lens is adequately guarded to keep any person from contacting it, the light shall be installed in or on a wall of the pool, with the top of the lens opening not less than 18 inches (457 mm) below the normal water level of the pool
ATTENTION INSTALLER : This manual contains important information about the installation, operation and safe use of this product. This information should be given to the owner/operator of this equipment.
NOTICE
The Jandy Pool and Spa lights are intended for installation in fresh water and non-fresh water swimming pools and spas. It is important to ensure that the wet niches in which the lights are installed are intended for their appropriate application, either fresh water or non-fresh water.
SAVE THESE INSTRUCTIONS**

Operating Instructions

2.1 To Operate the Light
Activate the light by either turning on the switch, setting a program, or by pushing the button on a pool and spa controller.

Replacing The Lamp

WARNING
Always disconnect the power to the pool or spa light at the circuit breaker before servicing the light. Failure to do so could result in death or serious injury to serviceman, pool or spa users or others due to electrical shock.

1. Turn off the main electrical switch or circuit breaker, as well as the switch, which operates the underwater light.

2. Be sure to have the following items:
   • A new lens gasket (P/N R0451101 for Jandy Pool Light and P/N R0400501 for Jandy Spa Light).
   • One (1) new lamp. See Table 1 for specifications.
   WARNING
   Replace the lamp with one of the same type and wattage. Failure to replace the lamp with one of the same type will damage the light assembly and may cause an electrical hazard resulting in death or serious injury to pool or spa users, installers, or others due to electrical shock, and may also cause damage to property. Be sure the power is switched  OFF before removing or installing lamps. Allow lamp to cool before replacing.

3. To remove the light assembly, unscrew the special pilot screw at the top of the face ring, remove light assembly from niche and gently place assembly on the deck. It is not necessary to drain down the pool or spa. See Figure 1.
   Jandy Model| Fixture Voltage| Lamp Voltage| Lamp Wattage| Lamp Type| Qty. per Fixture| Lamp Kit Part Number
   ---|---|---|---|---|---|---
   Pool/Spa White Light| 12 Volt AC| 12V| 100 Watt| R20 Flood| 1| R0450501
   Pool White Light| 120 Volt AC| 120V| 300 Watt| R40 Flood| 1| R0450502
   Pool White Light| 12 Volt AC| 12V| 300 Watt| R40 Flood| 1| R0450503
   Pool White Light| 120 Volt AC| 120V| 500 Watt| R40 Flood| 1| R0450504
   Spa White Light| 120 Volt AC| 120V| 60 Watt| R20 Flood| 1| R0450505

Table 1. Lamp Specifications

4. Disassemble the light fixture and replace lamp as follows:
   WARNING
   Be sure to keep the special pilot screw from this underwater light. This screw mounts and electrically grounds the housing securely to the mounting ring and wet niche. Failure to use the screw provided could create an electrical hazard, which could result in death or serious injury to pool or spa users, installers or others due to electrical shock.
   a. Loosen the eight (8) Phillips head screws for pool light or the six (6) Phillips head screws for spa light to allow the bottom clamp to be removed from the face ring assembly. Do not remove the screws or the retaining rings. The retaining rings prevent the screws from falling free from the top clamp and also aid in ease of assembly.
   b. Remove the lower clamp, the face ring assembly, the glass lens, and the gasket from the fixture.
   Remove the gasket from the lens. Refer to Section 4, Exploded View and Replacement Parts. c. Install new lamp.
   WARNING
   Risk of Electrical Shock or Electrocution. Always install a new lens gasket whenever disassembling the light (for Jandy Pool Light Gasket P/N R0451101 and for Jandy Spa Light Gasket P/N R0400501). Failure to do so may permit water to leak into the assembly, which could cause:
   (a) An electrical hazard resulting in death or serious injury to pool or spa users, installers, or others due to electrical shock, or
   (b) Breakage of the lamp or lens, which likewise could result in serious injury to pool or spa users, installers, or bystanders, or in damage to property.

5. Reassemble the fixture as follows:
   a. If not already done, remove the gasket from the glass lens and install a new gasket, Jandy Pool Light Gasket (P/N R0451101) and Jandy Spa Light Gasket (P/N R0400501), on the lens.
   NOT E A new lens gasket must be used each time the light is reassembled.
   b. While holding the fixture upright, place the glass lens with the gasket on top of the fixture. Please note that the lens gasket is not symmetrical. Therefore, it must be installed correctly so that  the lens can seal to the fixture housing. Place thegasket on the lens so that the thick molded side of the gasket will mate with the housing when the lens is installed. See Figure

6. c. Position the lens and gasket on the fixture. Place the face ring and the top clamp over the lens and align the pilot screw with the small arrow mark on the face of the lens. Note that the small arrow mark on the face of the lens and the pilot screw of the face ring must be aligned with the arrow located on fixture label that reads, “Arrow on this label must line up with the pilot screw on the Face Ring”. See Figure 2.
   d. While holding the aligned face ring assembly and fixture together, turn the assembly upside down and set it on the old gasket, using the old gasket as an assembly fixture. This will keep the lens and gasket assembly from being pushed out of the face ring while you secure it to the light fixture.
   e. Spread the bottom clamp over the electrical cord and slide it onto the back of fixture to the top clamp. See Figure 2.
   f. Tighten the eight (8) Phillips head screws for pool light or the six (6) Phillips head screws for spa light in alternating cross-pattern. Torque screws to approximately 20 in-lbs. Do not over-tighten.
   g. Discard the old gasket.

7. Reinstall the Jandy Light into niche fixture.
   a. Coil four (4) feet of cord around the fixture and place the light assembly into the niche.
   b. Engage the retainer tab on the bottom of the face ring, then pivot the top of the fixture inward and tighten the special pilot screw.
   
   WARNING
   Use only the special pilot screw provided with this underwater light. This screw mounts and electrically grounds the housing securely to the mounting ring and wet niche. Failure to use the screw provided could create an electrical hazard, which could result in death or serious injury to pool or spa users, installers or others due to electrical shock.

8. If pool or spa is empty, fill pool or spa until the underwater light is completely submerged in water before operating the light for more than 10 seconds. Turn on main switch or circuit breaker, as well as the switch, which specifically operates the underwater light, to check for proper operation.
   WARNING
   Never operate this underwater light for more than 10 seconds unless it is totally submerged in water. Without total submersion, the light assembly will get extremely hot, which may result in serious burns or in breakage of the lamp or lens. This may result in serious injury to pool or spa users, installers, or bystanders or in damage to property.

Exploded View and Replacement Parts

4.1 Jandy Pool White Light

4.2 Jandy Spa White Light

NOTES

ETL LISTED CONFORMS TO UL STD 676
Certified to CAN/CSA C22.2 No. 89
Zodiac Pool Systems, Inc.
2620 Commerce Way, Vista, CA 92081
1.800.822.7933 | www.ZodiacPoolSystems.com
©2014 Zodiac Pool Systems, Inc. ZODIAC® is a registered trademark of Zodiac International,
S.A.S.U., used under license. All trademarks referenced herein are the property of their respective owners.
H0312300 Rev B

References

• Zodiac Pool Systems United States | Zodiac Pool Systems

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>