AIRGUARD Bourgault Blockage Prevention System Instruction Manual
- June 10, 2024
- AirGuard
Table of Contents
Bourgault Blockage Prevention System
Instruction Manual
Bourgault Blockage Prevention System
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 1. For installations on both fans with rear hitch, the fan will need to
be shifted over for sufficient room to install the BP System. Disconnect
flexible outlet hose (Item 1) from the fan outlet on fan #1 and/or fan #2.
Loosen the U-Bolts / Bolts (Item 2) that hold the fan mount bracket to the
axle. In some cases the U-Bolts / Bolts may need to be removed completely and
reinstalled in the new location. Allow for 10-12” of space between the fan
motor and the intake screen of the neighboring fan. A 7” flexible hose
extension kit (Item 4) will be required when moving fan over. See pages 3-6
for specific relocation bracket installation inscructions. If installation is
only on the out- side fan, remove deflector shield (Item 3) and skip to page
8.| REV #| 1.0
PART KIT #| Varies
MODEL SPECIFIC CONNECTION WHEN INSTALLING ON
BOTH FANS WITH REAR HITCH: KIT #7923 or 9070
6000 Series Tow Behind
7000 Series Tow Behind
L9000 Series Tow Between
WARNING: Support fan housing from below with a jack or above with hoist
to avoid injury and so no extra stress is put on the hydraulic hose
connections
PARTS LIST
Item| Part #| Description
1| —| Flexible Outlet Hose
2| —| Existing Hardware U-Bolts / Bolts
PARTS LIST
Item| Part #| Description
3| —| Deflector Screen
4| 7923 /or/ 9070| 7” Flexible Hose
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 2. For Tow Behind installations with no rear hitch, for specific models
as per be- low. Bolt 45 deg bracket (Item 1) to Axle HSS (Item 2) using
backing plates (Item 3), 12mm x 130mm Bolts (Item 4) and 12mm Lock Nuts (Item
5) and Flat Washers (Item 6). Unbolt the fan (Item 7) from the Axle HSS (Item
2) and rebolt onto the 45deg bracket (Item 1) using the existing hardware from
the Fan.| REV #| 1.0
PART KIT #| Varies
MODEL SPECIFIC CONNECTION WHEN INSTALLING ON INSIDE
FAN OR ON BOTH FANS AND NO REAR HITCH: KIT #7945
6000series – Tow Behind
7000series – Tow Behind
PARTS LIST
Item| Part #| Description
1| 7942| 45deg Bracket
2| —| Axle HSS
3| 7943| Backing Plate
4| 7863| Hex Bolt, 12mm x 130mm
PARTS LIST
Item| Part #| Description
5| 7669| Lock Nut, 12mm
6| 7925| Flat Washer, 12mm
7| —| Fan
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 3. For L6000 Series tow between installations, for specific models as
per below. Re- move outside fan (Item 1) from Aircart Frame (Item 2). Bolt
extension bracket (Item 3) to Aircart Frame (Item 2) using existing hardware
(Item 4). Reattach fan (Item 1) to extension bracket (Item 3) using 12mm x
40mm Bolts (Item 5) and 12mm Lock Nuts (Item 6) and Flat Washers (Item 7). A
7” flexible hose extension kit (Item 8) will be required when moving fan
over.| REV #| 1.0
PART KIT #| Varies
MODEL SPECIFIC CONNECTION WHEN INSTALLING ON
OUTSIDE FAN OR ON BOTH FANS: KIT #7923 & 7924
L6000series – Tow Between
PARTS LIST
Item| Part #| Description
1| —| Fan
2| —| Aircart Frame
3| 7922| Extension Bracket
4| —| Existing Hardware
PARTS LIST
Item| Part #| Description
5| 7671| Hex Bolt, 12mm x 40mm
6| 7669| Lock Nut, 12mm
7| 7925| Flat Washer, 12mm
8| 7923| 7” Flexible Hose
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 4. For L7000 Series tow between installations, for specific models as
per below. Re- move outside fan (Item 1) from Aircart Frame (Item 2). Bolt
extension bracket (Item 4) to Aircart Frame (Item 2) using bracket plate (Item
5) with 12mm x 40mm Bolts (Item 6) and 12mm Lock Nuts (Item 7). Reattach fan
(Item 1) to extension bracket (Item 4) using existing U-bolts and nuts (Item
3). A 7” flexible hose extension kit (Item 8) will be required when moving fan
over.| REV #| 1.0
PART KIT #| Varies
MODEL SPECIFIC CONNECTION WHEN INSTALLING ON OUTSIDE FAN OR ON BOTH FANS: KIT
7923 & 7850
L7000series – Tow Between
PARTS LIST
Item| Part #| Description
1| —| Fan
2| —| Aircart Frame
3| —| Existing Hardware
4| 7845| Extension Bracket
PARTS LIST
Item| Part #| Description
5| 7846| Extension Bracket Plate
6| 7671| Hex Bolt, 12mm x 40mm
7| 7669| Lock Nut, 12mm
8| 7923| 7” Flexible Hose
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 5. For 71300 Series Aircart installations with rear hitch, remove
inside fan (Item 1) from axle HSS (Item 2). Bolt fan bracket (Item 3) to Axle
HSS (Item 2) using bracket plate (Item 4) with 12mm x 40mm Bolts (Item 5),
12mm x 50mm Bolts (Item 6) and 12mm Lock Nuts (Item 7). Reattach fan (Item 1)
to fan bracket (Item 3) using 12mm x 40mm bolts (Item 5) and 12mm Lock Nuts
(Item 7). A 7” flexible hose extension kit (Item 8) will be required when
moving fan over. When rear hitch is present, both fans must be moved over with
fan brackets.| REV #| 1.0
PART KIT #| Varies
MODEL SPECIFIC CONNECTION WHEN INSTALLING ON INSIDE FAN OR ON BOTH FANS WITH REAR HITCH : KIT #7923 & 7670 71300
PARTS LIST
Item| Part #| Description
1| —| Fan
2| —| Aircart Frame
3| 7665| Fan Bracket
4| 7668| Bracket Plate
PARTS LIST
Item| Part #| Description
5| 7672| Hex Bolt, 12mm x 50mm
6| 7671| Hex Bolt, 12mm x 40mm
7| 7669| Lock Nut, 12mm
8| 7923| 7” Flexible Hose
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 5. For 71300 Series Aircart installations with rear hitch, remove
inside fan (Item 1) from axle HSS (Item 2). Bolt fan bracket (Item 3) to Axle
HSS (Item 2) using bracket plate (Item 4) with 12mm x 40mm Bolts (Item 5),
12mm x 50mm Bolts (Item 6) and 12mm Lock Nuts (Item 7). Reattach fan (Item 1)
to fan bracket (Item 3) using 12mm x 40mm bolts (Item 5) and 12mm Lock Nuts
(Item 7). A 7” flexible hose extension kit (Item 8) will be required when
moving fan over. When rear hitch is present, both fans must be moved over with
fan brackets.| REV #| 1.0
PART KIT #| Varies
MODEL SPECIFIC CONNECTION WHEN INSTALLING ON INSIDE FAN OR ON BOTH FANS WITH REAR HITCH : KIT #7923 & 7670 71300
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 6. For 71300 Series Aircart installations with no rear hitch, remove
inside fan (Item 1) from axle HSS (Item 2). Bolt fan bracket plate (Item 3) to
Axle HSS (Item 2) using 12mm x 40mm Bolts (Item 4) and 12mm Lock Nuts (Item
5). Mount Angle Bricket (Item 6) to fan bracket plate (Item 3) using 12mm x
40mm Bolts (Item 4), 12mm washers (Item 7) and 12mm Lock Nuts (Item 5).
Reattach fan (Item 1) to Angle bracket (Item 6) using existing hardware.| REV
| 1.0
PART KIT #| Varies
MODEL SPECIFIC CONNECTION: FANS WITH FIXED SCREEN CAGES
HC Fans
HS Fans
HP Fans
PARTS LIST
Item| Part #| Description
1| —| Fan Screen
2| —| Fan Housing
PARTS LIST
Item| Part #| Description
3| —| Outer Flat Bar Ring
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 8. For HC, HS and HP Fans with spinner screens, remove existing fan
screen (Item 1) from the fan housing (Item 2) by removing the outer flatbar
ring (Item 3). Remove existing fan spinner screen assembly parts (Item 4) from
the fan housing (Item 2). All spinner parts including center shaft should be
removed. Screen material (Item 1) must be cut to free sensor plug.| REV #| 1.0
PART KIT #| Varies
MODEL SPECIFIC CONNECTION: FANS WITH SPINNER SCREEN CAGES
HC Fans
HS Fans
HP Fans
PARTS LIST
Item| Part #| Description
1| —| Fan Screen Spinner Assembly
2| —| Fan Housing
PARTS LIST
Item| Part #| Description
3| —| Fan Screen
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 9. Install supplied mounting bracket (Item 1) to fan housing (Item 2)
using existing bolts and nuts (Item 3). Angle mount bracket in a position that
ensures the supplied hydraulic hoses reach the fan motor. Additional holes in
bracket face (Item 4) are for easy access with an impact driver. For Kit
9640, bracket will need to be bolted togeth- er using supplied hardware and
plates. Bracket may look different than shown below.| REV #| 1.0
PART KIT #| Varies
Use Kit # 9510 for the following Mode4000series
5000series
6000series HS & HC Fans
7000series HS & HC Fans
8000series HS & HC Fans
9000series HS & HC Fans
Use Kit # 9610 for the following Models with
screen spinners:
7000series HP Fans
8000series HP Fans
9000series HP Fans
Use Kit # 9640 for the following Models with Screens attached to fan
housing:
7000series HP Fans
8000series HP Fans
9000series HP Fans
| PARTS LIST | PARTS LIST |
|---|---|
| Item | Part # |
| 1 | 7553 / or / 9019 |
Existing Hardware
2| —| REM Fan Housing / or / Tsunami Blower Housing|
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 10. Bolt Oil Cooler/Radiator Assembly (Item 1) to BP System Bracket
(Item 2) using supplied 10mm x 25mm Bolts (Item 3)and 10mm lock nuts (Item 4).
If only installing snorkel kit without Radiator, then install plastic plugs
(Item 5) onto BP Sytem Bracket (Item 2). This step of the installation may
already be completed at the Airguard facto- ry prior to shipping.| REV #| 1.0
PART KIT #| Varies
PARTS LIST
Item| Part #| Description
1| 7996| Oil Cooler and Manifold Assembly
2| 7546| Main BP System Bracket
3| 7515| Hex Bolt, 10mm x 25mm Grade 8.8
PARTS LIST
Item| Part #| Description
4| 7516| Lock Nut, 10mm Grade 8.8
5| 7683| BP System Bracket Plug
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 11. Remove the plastic packaging materials prior to the assembly of
these brackets. Mount BP System Main Bracket with Oil Cooler (Item 1) or Main
Bracket with Plugs (Item 2) to Fan bracket (Item 3) using supplied pivot pins
(Item 4). Secure in place with 3.5mm cotter pins (Item 5).| REV #| 1.0
PART KIT #| Varies
PARTS LIST
Item| Part #| Description
1| —| BP System Main Bracket with Oil Cooler
2| —| BP System Main Bracket with Plugs for Snorkel Only Install
3| —| REM RT Fan Bracket / or / Tsunami Blower Bracket
PARTS LIST
Item| Part #| Description
4| 7502| Pivot Pin For BP Systems
5| 7513| 3.5mm Cotter Pin
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 12. Attach Mesh Screen (Item 1) or Snorkel Housing (Item 2) to front of
BPS using latches (Item 3).| REV #| 1.0
PART KIT #| Varies
PARTS LIST
Item| Part #| Description
1| 7568| Mesh Screen
2| 7977| Snorkel Housing
PARTS LIST
Item| Part #| Description
3| —| Overcenter Latch
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 13. Identify the model of aircart that the Airguard Blockage Prevention
System is being installed on. For models with external check valves, the
connections must be made on the tractor side of the hydraulic circuit as shown
below.| REV #| 1.0
PART KIT #| Varies
Installation with External Check Valve:
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 14. Remove factory hoses (Item 1) from side of fan motor (Item 2).
Remove the hoses (Item 1) on the tractor side of the external check valve, as
shown below. Identify which hose is the pressure side of the circuit. The
external check valve will have a di- rectional arrow that always points to the
pressure side. If you do not have an external check valve you will attach
directly to the fan motor.| REV #| 1.0
PART KIT #| Varies
PARTS LIST
Item| Part #| Description
1| —| Existing Hose from Tractor to Fan Motor
2| —| Hydraulic Motor
PARTS LIST
Item| Part #| Description
3| —| External Check Valve
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 15. Hoses may be routed to suit your specific aircart installation.
Install supplied 3/4” hydraulic hose (Item 1) to the “TRACTOR PRESSURE” port
of the radiator block (Item 2), using adapter (Item 3) to make the connection.
Use model specific connec- tion as per instuctions below to attach the other
end of the hose to the factory pres- sure line (Item 4) that was removed from
the fan motor.| REV #| 1.0
PART KIT #| Varies
PARTS LIST
Item| Part #| Description
1| 9016| BPS 3/4” Hydraulic Hose – 60”
2| —| “TRACTOR PRESSURE” Port – BP System Manifold
3| 7506| Fiting – Elbow – 3/4” JIC Male – 3/4” ORB Male
PARTS LIST
Item| Part #| Description
4| —| Tractor Supply (Pressure) Hydraulic Hose
5| 7538| Fitting – Straight – 3/4” JIC M – 3/4” JIC M
6| 7237| Fitting – Straight – 1” JIC M – 3/4” JIC M
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 16. Install supplied 3/4” hydraulic hose (Item 1) to the “TRACTOR
RETURN” port of the radiator block (Item 2) using adapter (Item 3). Use model
specific connection as per instuctions below to attach the other end of the
hose to the factory pressure line (Item 4) that was removed from the fan
motor.| REV #| 1.0
PART KIT #| Varies
All of the hydraulic connections in Step 8 to 12 should only be hand tightened until all hoses and fittings are installed. Some connections may need to be rotated in order to install other components
PARTS LIST
Item| Part #| Description
1| 9016| BPS 3/4” Hydraulic Hose – 60”
2| —| “TRACTOR RETURN” Port – BP System Manifold
3| 7506| Fiting – Elbow – 3/4” JIC Male – 3/4” ORB Male
PARTS LIST
Item| Part #| Description
4| —| Tractor Return Hydraulic Hose
5| 7538| Fitting – Straight – 3/4” JIC M – 3/4” JIC M
6| 7237| Fitting – Straight – 1” JIC M – 3/4” JIC M
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 17. Install supplied 3/4” hydraulic hose (Item 1) to the “FAN PRESSURE”
port of the radiator block (Item 2) using adapter (Item 3). Use model specific
connection as per instuctions below to attach the other end of the hose to the
factory fan pressure line/ port (Item 4) coming from the fan motor.| REV #|
1.0
PART KIT #| Varies
PARTS LIST
Item| Part #| Description
1| 9016| BPS 3/4” Hydraulic Hose – 60”
2| —| “FAN PRESSURE” Port – BP System Manifold
3| 7506| Fiting – Elbow – 3/4” JIC Male – 3/4” ORB Male
PARTS LIST
Item| Part #| Description
4| —| Fan Supply (Pressure) Hydraulic Hose
5| 7238| Fitting – Straight – 1” JIC F – 3/4” JIC M
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 18. Install supplied 3/4” hydraulic hose (Item 1) to the “FAN RETURN”
port of the radiator block (Item 2) using adapters (Item 3 & 5). Use model
specific connection as per instuctions below to attach the other end of the
hose to the factory fan return line/ port (Item 4) coming from the fan motor.|
REV #| 1.0
PART KIT #| Varies
PARTS LISTC
Item| Part #| Description
4| —| Fan Return Hydraulic Hose
5| 7238| Fitting – Straight – 1” JIC F – 3/4” JIC M
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 19. Install supplied 1/2” hydraulic hose (Item 1) to the “CASE DRAIN”
port of the radiator block (Item 2) using adapters (Item 3 & 4). and to the
fan motor case drain line (Item 5). Use model specific connection as per
instuctions below to attach the other end of the hose to the factory fan case
drain line/port (Item 5) coming from the fan motor.| REV #| 1.0
PART KIT #| Varies
PARTS LIST
Item| Part #| Description
1| 9016| BPS 3/4” Hydraulic Hose – 60”
2| —| “FAN CASE DRAIN” Port – BP System Manifold
3| 7264| Fitting – Straight – 1/2” JIC Male – 3/8” ORB Male
PARTS LIST
Item| Part #| Description
4| 7686| Fiting – Elbow – 1/2” JIC M – 1/2” JIC F
5| —| Fan Case Drain Hydraulic Hose
6| 7263| Fitting – Tee – 1/2” JIC M – M – F
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 20. Complete the hydraulic installation by ensuring that all
connections made in Step 8 to 12 are tightened. Position/Routing of hydraulic
hoses may vary to suit each spe- cific machine installation. Zip tie hoses to
reduce wear and ensure tidy installation.| REV #| 1.0
PART KIT #| Varies
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 21. For snorkel mount on specific aircarts as per below. Install the
bracket (Item 1) onto the Aircart Stair Tread (Item 2) using existing stair
tread hardware (Item 3).| REV #| 1.0
PART KIT #| Varies
MODEL SPECIFIC CONNECTION – KIT 9000:
7550, 7700, 7950, 71300 L7550, L7701,
L7800 8350, 8450, 8550 L8350, L8450, L8550 9650, 9950, 91300 L9650, L9950
PARTS LIST
Item| Part #| Description
1| 9001| Bourgault Snorkel Mount Bracket
2| —| Stair Tread
PARTS LIST
Item| Part #| Description
3| —| Existing stair tread hardware
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 22. Mount Outer Vertical Channel (Item 1) to Bracket (Item 2) using
supplied 12mm x 80mm Bolts (Item 3) and 12mm lock nuts (Item 4).| REV #| 1.0
PART KIT #| Varies
MODEL SPECIFIC CONNECTION – KIT 9000:
7550, 7700, 7950, 71300 L7550,
L7701, L7800 8350, 8450,
8550 L8350, L8450,
L8550 9650, 9950, 91300 L9650, L9950
PARTS LIST
Item| Part #| Description
1| 7865| Outer Vertical Channel
2| 9001| Bourgault Snorkel Mount Bracket
PARTS LIST
Item| Part #| Description
3| 7859| Hex Bolt, 12mm x 80mm
4| 7669| Lock Nut, 12mm
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 23. Attach air intakes (Item 1) to upper vertical channel (Item 2)
using supplied 10mm x 25mm Bolts (Item 3) and 10mm lock nuts (Item 4). A
maximum of 4 intakes can be mounted. Use bridge clamp (Item 5) to attach 8”
flex hose (Item 6) to air intake (Item 1).| REV #| 1.0
PART KIT #| Varies
MODEL SPECIFIC CONNECTION – KIT 9000: 7550, 7700, 7950, 71300 L7550, L7701, L7800 L8350, L8450, L8550 9650, 9950, 91300 L9650, L9950
PARTS LIST
Item| Part #| Description
1| 7576| Air Intake Bracket
2| 7868| Upper Vertical Channel
3| 7515| Hex Bolt, 10mm x 25mm
PARTS LIST
Item| Part #| Description
4| 7516| Lock Nut, 10mm
5| 7578| Bridge Clamp, 8”
6| 7572| Flexible Snorkel Hose – 8”
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 24. Determine desired height of air intakes and secure upper vertical
channel (Item 1) to lower vertical channel (Item 2) at that location. Use
supplied 12mm x 80mm Bolts (Item 3) and 12mm lock nuts (Item 4).| REV #| 1.0
PART KIT #| Varies
MODEL SPECIFIC CONNECTION – KIT 9000: 7550, 7700, 7950, 71300, L7550, L7701, L7800 8350, 8450, 8550 L8350, L8450, L8550 9650, 9950, 91300 L9650, L9950
PARTS LIST
Item| Part #| Description
1| 7868| Upper Vertical Channel
2| 7865| Outer Vertical Channel
PARTS LIST
Item| Part #| Description
3| 7859| Hex Bolt, 12mm x 80mm
4| 7669| Lock Nut, 12mm
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 25. Attach stabilizer bracket (Item 1) to catwalk railing (Item 2)
using railing mount plate (Item 3) and supplied 12mm x 80mm Bolts (Item 4) and
12mm lock nuts (Item 5).| REV #| 1.0
PART KIT #| Varies
MODEL SPECIFIC CONNECTION – KIT 9000: 7550, 7700, 7950, 71300, L7550, L7701, L7800 8350, 8450, 8550 L8350, L8450, L8550 9650, 9950, 91300 L9650, L9950
PARTS LIST
Item| Part #| Description
1| 7868| Upper Vertical Channel
2| —| Catwalk Railing
3| 7959| Railing Mount Plate
PARTS LIST
Item| Part #| Description
4| 7859| Hex Bolt, 12mm x 80mm
5| 7669| Lock Nut, 12mm
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| 26. Attach 8” flex hose (Item 1) to snorkel housing (Item 2) using
bridge clamp (Item 3). Zip tie 8” flex hoses to reduce wear and ensure tidy
installation.| REV #| 1.0
PART KIT #| Varies
PARTS LIST
Item| Part #| Description
1| 7977| Snorkel Housing
2| 7578| Bridge Clamp, 8”
PARTS LIST
Item| Part #| Description
3| 7572| Flexible Snorkel Hose – 8”
Title| Airguard Blockage Prevention System Upgrade Instructions| RELEASE DATE|
2023-03-01
---|---|---|---
STEP| Installation is Completed. Ensure all hydraulic connections and bolts
are tightened.| REV #| 1.0
PART KIT #| Varies
Release Date: 2023-03-01
Part Kit #VARIES – Rev 1.0 – AIRGUARD – Blockage Prevention System
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>