ZKTeco LB330 Parking Barrier User Manual

User Manual
LB330 Parking Barrier
Date: June 2022
Doc Version: 1.0

LB330 Parking Barrier

Thank you for choosing our product. Please read the instructions carefully before operation. Follow these instructions to ensure that the product is functioning properly. The images shown in this manual are for illustrative
For further details, please visit our Company’s website www.zkteco.com.

Copyright © 2022 ZKTECO CO., LTD. All rights reserved.
Without the prior written consent of ZKTeco, no portion of this manual can be copied or forwarded in any way or form. All parts of this manual belong to ZKTeco and its subsidiaries (hereinafter the “Company” or “ZKTeco”).

Trademark
is a registered trademark of ZKTeco. Other trademarks involved in this manual are owned by their respective owners.

Disclaimer
This manual contains information on the operation and maintenance of the ZKTeco equipment. The copyright in all the documents, drawings, etc. in relation to the ZKTeco supplied equipment vests in and is the property of ZKTeco. The contents hereof should not be used or shared by the receiver with any third party without the express written
permission of ZKTeco.
The contents of this manual must be read as a whole before starting the operation and maintenance of the supplied equipment. If any of the content(s) of the manual seems unclear or incomplete, please contact ZKTeco before starting the operation and maintenance of the said equipment.
It is an essential pre-requisite for the satisfactory operation and maintenance that the operating and maintenance personnel are fully familiar with the design and that the said personnel have received thorough training in operating and maintaining the machine/unit/equipment. It is further essential for the safe operation of the machine/unit/equipment that personnel have read, understood, and followed the safety
instructions contained in the manual.
In case of any conflict between terms and conditions of this manual and the contract specifications, drawings, instruction sheets or any other contract- related documents, the
contract conditions/documents shall prevail. The contract specific conditions/documents shall apply in priority.
ZKTeco offers no warranty, guarantee or representation regarding the completeness of any information contained in this manual or any of the amendments made thereto. ZKTeco does not extend the warranty of any kind, including, without limitation, any warranty of design, merchantability, or fitness for a particular purpose.
ZKTeco does not assume responsibility for any errors or omissions in the information or documents which are referenced by or linked to this manual. The entire risk as to the results and performance obtained from using the information is assumed by the user.
ZKTeco in no event shall be liable to the user or any third party for any incidental, consequential, indirect, special, or exemplary damages, including, without limitation, loss of business, loss of profits, business interruption, loss of business information or any pecuniary loss, arising out of, in connection with, or relating to the use of the information contained in or referenced by this manual, even if ZKTeco has been advised of the possibility of such damages.
This manual and the information contained therein may include technical, other inaccuracies or typographical errors. ZKTeco periodically changes the information herein which will be incorporated into new additions/amendments to the manual. ZKTeco reserves the right to add, delete, amend, or modify the information contained in the manual from time to time in the form of circulars, letters, notes, etc. for better operation and safety of the machine/unit/equipment. The said additions or amendments are meant for improvement /better operations of the machine/unit/equipment and such amendments shall not give any right to claim any compensation or damages under any circumstances.
ZKTeco shall in no way be responsible (i) in case the machine/unit/equipment malfunctions due to any non-compliance of the instructions contained in this manual (ii) in case of operation of the machine/unit/equipment beyond the rate limits (iii) in case of operation of the machine and equipment in conditions different from the prescribed conditions of the manual.
The product will be updated from time to time without prior notice. The latest operation procedures and relevant documents are available on http://www.zkteco.com.
If there is any issue related to the product, please contact us.

ZKTeco Factory India

Address B-1, Khata No.31, Devasandra Industrial Estate, Whitefield Main Road, Beside Phoenix Mall, Mahadevapura, Bengaluru, Karnataka.
Phone 080 6828 1342
For business-related queries, please write to us at india@zkteco.com.
To know more about our global branches, visit www.zkteco.com.

About the Company
ZKTeco is one of the world’s lagest manufacturers of RFID and Biometric (Fingerprint, Facial, Finger-vein) readers. Product offerings include Access Control readers and panels, Near & Far-range Facial Recognition Cameras, Elevator/floor access controllers, Turnstiles, License Plate Recognition (LPR) gate controllers and Consumer products including battery-operated fingerprint and face-reader Door Locks. Our security solutions are multi-lingual and localized in over 18 different languages. At the ZKTeco state-of-the-art 700,000 square foot ISO9001certified manufacturing facility, we control manufacturing, product design, component assembly, and logistics/shipping, all under one roof.
The founders of ZKTeco have been determined for independent research and development of biometric verification procedures and the productization of biometric verification SDK, which was initially widely applied in PC security and identity authentication fields. With the continuous enhancement of the development and plenty of market applications, the team has gradually constructed an identity authentication ecosystem and smart security ecosystem, which are based on biometric verification techniques. With years of experience in the industrialization of biometric verifications, ZKTeco was officially established in 2007 and now has been one of the globally leading enterprises in the biometric verification industry owning various patents and being selected as the National High-tech Enterprise for 6 consecutive years. Its products are protected by intellectual property rights.

About the Manual
This manual introduces the operations of LB330 Parking Barrier.
All figures displayed are for illustration purposes only. Figures in this manual may not be exactly consistent with the actual products.

Document Conventions
Conventions used in this manual are listed below:
GUI Conventions

For Device

brackets. For example, pop up the [New User] window.
/| Multi-level menus are separated by forwarding slashes. For example, [File/Create/Folder].

Symbols

cautionary example.

Overview

The LB330 is intended for use in small parking spaces, such as those for two- wheelers and small cars. It is a low-cost barrier with a high-performance DC brushless motor and two arm lengths of 1.5 and 2 meters, as well as a spherical type of boom arm. It also features inbuilt LED lights mostly night lights that turn on when there is a dark light condition; this is controlled by a sensor that detects low light. It has two remote controllers and is compatible with LPR cameras, UHF readers, and biometric devices.

Features and Functionalities

1. The fastest operating speed is 5s, the speed can be adjusted according to different boom arm lengths.
2. Digital control monitoring supports delay automatic close functions.
3. High safety, support power off manually rise boom arm, anti-smash functions.
4. The position of the angle of rising/fall can be adjusted, and the digital encoder is adopted to limit the position automatically, replacing the traditional limit structure, and the position control is accurate.
5. The barrier boom will rebound when it is blocked.
6. Invertibility in left and right direction, simple and compact transmission mechanism, easy to install on site.

Appearance and Dimensions

Specifications

Installation Procedure

Installation Precautions

1. Install the parking barrier on a flat surface. A cement foundation is required before installation if the ground is not solid and flat.
2. It is possible to reduce the length of the boom, but it cannot be increased. After the boom has been cut, it is important to set the spring balance again to achieve a new balance. The bottom of the spring contains two plastic nuts designed to adjust the new balance.
3. When the barrier is powered on, do not change the wire connection inside.
4. Connect the GND to the cabinet to ensure protection.

Tools Preparation
Make sure you have all the tools that you will need to do the job. The following is a list of tools that are required:

• Impact Drill
• Adjustable Wrench
• Hammer
• Needle-nose Pliers
• Hexagon Wrench (Allen Key)
• Screwdriver, etc.

3.1 Installation of the Base and the Casing

1. Remove the four screws from the casing and the base as shown in the illustration.
2. Make sure the wire slot in the centre of the base is pre-opened.
3. The base has a downward opening. Fix the location with the expansion screw M10 x 120 after identifying it.
4. Place the casing on the base and install and tighten the four screws.

The barrier’s base is shown in the figure below:

5.4 Boom Arm Installation
5.4.1 Boom Arm Installation Procedure

1. Install the handlebar head: Make sure the flat key on the main shaft is aligned with the key notch on the handlebar head, then gently tap the handlebar head in place. Please see the figure below.
2. Install the centre screw and tighten it.
3. Attach the boom arm to the boom holder’s head.
4. Install the remaining two screws and tighten them.
5. Connect the LED light’s power cord.

Main Control Board Instructions

1. Before you begin wiring, make sure the power supply is turned off.
2. Make sure that the terminals are securely fastened and that the wiring is secure.

6.1 Control Board External Product Requirement
External product requirements for the control board are:

• Power supply -24V/4 to 10 A;
• Motor type: 24DC Brushless motor.
• Vehicle detector or 12V radar ground sensor.

6.2 Main Board Wiring Diagram

Note: Network cables must not be connected to any of the control board’s external signal lines. Although the network wires have no connectivity issues, they are easily broken after numerous tosses. To reduce the issues caused by line faults, it is advisable to use BVR lines.

6.3 Main control Board Operation
6.3.1 Self-inspection Learning Switch Barrier Limit Method:

1. Long press the “key” of the control board for 2 seconds after it begins normally (“190” is displayed). The main board display value decreases as the barrier moves in the direction of closing the gate. The main board display returns to “190” when the motor reaches the closing limit, and the closing self-check is completed.
2. Press and hold the “On” button on the main board for 2 seconds after the shutdown self-check is done. The display value on the main board increases as the gate moves in the gate opening direction. The main board buzzer beeps for a long time when the motor reaches its open limit. The self-check for the opening is now complete, and the gate can be used normally.

6.3.2 Operation Steps of the Main Board Buttons:

1. Press and hold the main board menu button until L-1 is appearing.
2. To select the menu directory, press the “On” or “Close” key on the mainboard. If you need to enter this directory, press the “Menu” key on the mainboard once.
3. if you need to modify a catalogue parameter, after accessing the menu catalogue, hit the “No” and “Off” keys to increase or decrease this menu parameter, once the
   alteration is complete, if you need to change other catalogue parameters, click the “Menu” key once to return to the previous menu catalogue. Return to the main menu and proceed with the second step. If you do not alter any other settings, you may save and exit the menu by pressing the “Confirm” key on the mainboard.

6.4 Parameter Settings Description

Menu| Numerical
Menu| Function| Default Parameters| Parameter Range
---|---|---|---|---
L-1| LO1| Gate opening speed: larger value, the speed is faster| 65| 20-95
L-2| L02| Gate closing speed:larger value, the speed is faster| 65| 20-95
L-3| LO3| Stability in place: smaller value, it is more stable, if it is too small, it may not be closed in place| 12| 8-15
L-5| LO5| Velocity and menu: the greater the value, the greater the force.
Old number: letter menu, even number value menu| 70| 70-90
L-6| L06| Horizontal adjustment: the smaller the value, the smaller the angle of
the brake lever| 20| 3-90
L-7| L07| Aging test mode:0: manual 1: automatic, 1-5 is the time interval of
automatic operation, 1 is the fastest, 5 is the slowest, and 6 is a half-stoke operation| 0| 0-6
L-8| L08| Open gate counting function: 0: without counting, 1: with counting
4: peak mode (after opening the gate in place, press the remote
control stop button to turn it on, and close the remote control button
to close the gate)| 0| 0-1-4
L-9| L09| Vertical adjustment: the smaller the value,the smaller the opening angle| 20| 3-90
L-L| LI 0| Opening deceleration stroke of the  first stage: the smaller the value, the smaller the opening deceleration stroke| 55| 20-90
L-b| L11| The first stage of closing deceleration stroke: the smaller the value, the smaller the closing deceleration stroke| 55| 0-255
L-d| L13| Passive gate movement forward and reverse mode:0/3: left and right
running direction of the same model of motor;/: left and right
running direction of the same model of motor| 0| 0-3
L-E| L14| Gate closing direction self-check running speed: the larger the value,
the faster the speed, it is only use to adjust the gate-closing direction
self-check speed when the main board is powered on| 30| 0-49
L-F| L15| Remote paring and unpairing| 0| 0-255
L-H| L16| The second deceleration stroke for opening and closing the gate: the
parameter is set within the first deceleration stroke| 0| 0-20
L-18| L18| Relay output mode when the switch is in place: 0 traffic light model in-
position detection status mode; 3 light sensing mode| 0| 0-3
L 19| L19| Pressure ground sensing delayed closing time setting: set the value to
delayed closing time (seconds) 000 means that this function is not
enabled| 0| 0-255
L 20| L20| The setting of automatic gate-off time after opening: set the value to
the time of automatic gate-off after the gate is opened (seconds) 000
means that this function is not enable| 0| 0-255
L 21| L21| Communication machine number setting: set the value to the
machine number during communication, and the communication can be normal only if the machine number matches| 70| 0-255
I 22| L22| Running reverse buffer setting: when the brake lever is running,
the sudden reverse buffer time the setting, each number represents 0.1 second| 30| 0-59
L 23| L23| Sensitivity setting: the smaller the value, the more sensitive the light
source is| 50| 0-255
L-24|  L24| Operating speed of reverse self-check of gate opening: the larger the value, the faster the speed, which is only used to adjust the speed of self-checking in the the direction of opening the gate when the main board is energized and self-checked| 30| 0-49

6.5 Remote Control Pairing and Unpairing
6.5.1 Remote Control Pairing:

1. Long press Menu , then Long press the “Menu” button to enter the menu, select the L-F option, click the “Menu” button to display 000, and then enter the remote-control setting.
2. Press the remote control “Any key” and the main board will beep once, and the display will change to “L-F” to match the remote control successfully.
3. Press the “Confirm” button to save, and the configuration is complete.

6.6 Reset

1. Long press the “Confirm” button on the main board and wait for the buzzer to beep three times before releasing it. All parameters will be reset to their factory default values at this time.

Troubleshooting

gate lever gently.
2| The automatic function cannot lift the gate lever.| To open the gate, turn off the electricity and slowly lift the boom arm as described in the previous paragraph.
3| The self-inspection is
unsuccessful and the barriers are not operating normally.| Check to see if the L-d motor’s left and right rotation modes are compatible with the current motor. After changing the parameters, you can restart the main board to re- check the self-check.
4| The barrier rod is not in the vertical or horizontal position.| Adjust the parameters of the main board menu L-9 or L6 (please refer to the parameter table for menu functions).
5| The barrier rod is not in the
vertical or horizontal position| Set the L-18 parameter of the main board to 1, if the relay will act once when it is opened (or closed), it means it has been opened (or closed).
If the motor steps moving while the barrier is in position, it indicates it is in place. If the barrier is still in place and the motor is still operating, you must modify the L-6 or L-9 parameter.
6| The rebound function fails when there is resistance.| Check if the L-C parameter will rebound in the face of resistance (the main board parameter is greater than 100, and the rebound function will fail).
The mainboard must be opened to the position and closed to the position twice to run, and the rebound function will only activate when it detects resistance after the mainboard self-check is successful or after entering and exiting the menu.
7| During regular functioning, the barriers unexpectedly reverse their orientation.| Increase the value of the L-C rebound function parameter when is encounters resistance.

Safety Precautions

• It is highly forbidden to hit the product using hard items.
• When using, please handle with care to avoid strong collisions with hard objects.
• Do not spill water or corrosive liquids on the surface of the product.
• The operation will not be possible whether the motor wire is connected appropriately, or the connection method is incorrect.
• If smoke or a strange smell comes from the product, disconnect the power immediately.
• If the product works abnormally, please contact the dealer in time. Please do not try to repair it by yourself. If you handle it without authorization, the company is not responsible for any damage

Transportation and Storage

• While loading and unloading the product, please handle it with care.
• During transportation and storage, place the product in a dry and corrosive-free environment. The product should be protected from moisture, rain, sun, and corrosion.

Copyright©2022 ZKTECO CO., LTD.
All rights reserved.

References

• ZKTeco | Biometrics and Computer Vision
• ZKTeco | Biometrics and Computer Vision

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>