HALCYON P471 LED High Bay Light Instruction Manual

June 10, 2024
HALCYON

HALCYON P471 LED High Bay Light

Wiring Diagram

HALCYON-P471-LED-High-Bay-Light-
FIG-1

Troubleshooting

Problem Possible Cause Solutions
**** LEDs stop working The power line is improperly connected. Reconnect

the power cable.
The power plug is loose.| Firmly plug the power in.
The LED driver malfunctions.| Replace with the new driver.
The LED chip is damaged.| Replace with new LEDs.
**** LEDs flash on and off| The output of the driver is abnormal.| Replace with the new driver.
The LED chip breaks down.| Replace with new LED chip.

Warranty

5 years warranty for original purchaser of LEDproduct that is identified on seller’s invoice reflecting its original purchase (the “Product”).

  1. In order to make a warranty claim, you must notify seller in writing within sixty (60) days after your discovery of the defect, provide proof of purchase such as the invoice and comply with seller’s other warranty requirements. Upon receiving that notice, to ascertain why fixtures stop working, evidences would be needed for seller’s QC Team to analyze. Seller may require you to promptly return the Product to Seller when necessary, freight prepaid.
  2. The determination ofwhether the Product is defective shall be made by Seller in its sole discretion with consideration given to the overallperformance of the Product.
  3. If seller determines the Product is defective, Seller will elect, in its sole discretion, repair the Product or replace the Product. Seller reserves the right to utilize new, reconditioned, refurbished, repaired or remanufactured products or parts in the warranty repair or replacement process. Such products and parts will be comparable in function and performance to an original product or part, as determined by Seller in its sole discretion, and warranted for the remainder of the original warranty period. However, cost of labor and equipment to remove the defective product and install a repaired or a replacement Product at the end-user facility are excluded. Supplier’s aggregate liability with respect to a defective product shall in any event be limited to the money paid to buyer for that defective product.

The following circumstances will not be warranted:

  1. Damage caused by force majeure such as war, riots, sabotage, cyclones, earthquakes, tidal waves, flooding, lighting strikes, explosions, fire, flood, etc.
  2. Damage caused by user’s improper delivery, defects caused by wrong operation, wrong treatment and destruction of machinery.
  3. Dismantling or modification or improper maintenance or repairing of the products without the supplier’s authorization.
  4. Damage caused by buyer or installer using bad quality cable or other mismatching electronic parts.
  5. This warranty is invalid if the product is not used for the purpose for which is originally designed. Any disputes occurred shall be applied to the laws and regulations of P.R.C. The seller has the sole right to interpret and amend the above articles.
Reminder
  • We appreciate your purchase!
  • Please read the instruction manual before installation and keep it for future reference.

Warning

  1. To avoid damage, falling, electric shock or fire, please do not modify the lamp or replace accessories without confirming with the supplier first.
  2. Please authorize only qualified personnel to install the lamp and ensure they follow the instructionmanual. Any improper installation might cause falling, electric shock, fire, or other injury, damage or hazard.
  3. Please disconnect power before installation or any maintenance of the lamp.
  4. Please disconnect power if it begins to smoke or emit odors, since fire or electric shock may occur. Ask qualified person to inspect and maintain the luminaire.
  5. Please do not dismantle the lamp without the supplier’s authorization.
  6. Please do not touch the power supply when the lamp is operating.
  7. If the external flexible cable or cord of the luminaire is damaged, it should only be replaced by the supplier, a service agent or qualified person.
  8. Terminal block not included. Installation may require advice from a qualified person.
  9. The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similarly qualified person.
  10. Only to be installed outside arms reach.
  11. For use in environments where an accumulation of non-conductive dust on the luminaire may be expected.
  12. Mounting heights of lights not higher than 30m.
  • Installation   note: Do not install on the same circuits as Metal halide, Fluorescent, and other Low power factor” devices.
  • When installed on the same circuit it can cause flickering and/or premature failure of the “high power factor” electronic drivers. The harmonic distortion from low power factor devices alters the Waveform of the AC supply which can cause componentry in high power factor electronic drivers to resonate, run over temperature and fail after prolonged exposure.
  • Caution risk of electric shock

Application

  • With a unique high-purity die-cast aluminum heat sink, high-brightness MD chip, high-efficiency constant current, and constant voltage power driver, the LED high bay is designed for factories, workshops, warehouses, highway toll stations, gas stations, supermarkets, exhibition halls, stadiums, and similar applications.

Technical Parameters

Product Specifications 100W 120W 150W 180W
Input Voltage AC100-240V / AC100-277V / AC200-240V / AC220-240V / AC277-480V
Power Frequency 50 / 60Hz
Outlook Dimensions 0 421x 385mm(16.57″ x15 .16 “)
Luminaire Net Weight 4.7±0.3kg (10.36±0.66Lbs) 4.8±0.3kg (10.58±0.66Lbs) 5

. 0±0. 3 kg (11.02±0.66Lbs)
Working Temperature| -30°C to +50°C (-22°F to +122°F)| -30°C to +40°C (-22°F to +104°F)
Storing Temperature| -40°C to +70°C (-40°F to +158°F)

Installation Instructions

Loop hanging installationHALCYON-P471-LED-High-Bay-Light-
FIG-2

  • Install the Anti-glare diffuser body to LED high bay with 3 supplied screws.
  • Put the clips and threaded holes in matching positions.
  • Push the cover in a clockwise direction to make the clips locked tight, fasten the diffuser body, and cover with the supplied screw.HALCYON-P471-LED-High-Bay-Light-FIG-4

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

HALCYON User Manuals

Related Manuals