Joy-it Mems Microphone On Breakoutboard Instruction Manual

: June 6, 2024
: JOY-It

Table of Contents

GENERAL INFORMATION
USAGE WITH THE RASPBERRY PI
USAGE WITH THE ARDUINO
- Connection
- Code example
OTHER INFORMATION
SUPPORT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Joy-it Mems Microphone On Breakoutboard Instruction Manual

GENERAL INFORMATION

Dear customer,

thank you very much for choosing our product.
In the following, we will introduce you to what to observe while starting up and using this product.

Should you encounter any unexpected problems during use, please do not hesitate to contact us.

USAGE WITH THE RASPBERRY PI

For use with the Raspberry Pi, you need an analog-digital converter. For this purpose, you can use our product COM-KY053ADC. You can find more information about this product here.

Connection

Connection Instructions

Installation

For the following code example, you need a operating system with graphical user interface. We recommend Raspberry Pi OS with desktop and recommended software.

First, enable I2C on your Raspberry Pi. To open the configuration, enter: sudo raspi-config

There, select 3 Interface Options → P5 I2C.

Installation Instructions

There, you get the question Would you like the ARM I2C Interface to be enabled? Confirm this with Yes.

Installation Instructions

You have now successfully activated I2C. The analog-digital converter is now accessible under the I2C address 0x48.
We use the Adafruit_Python_ADS1x15 library for our code example, which is released under the MIT- Lizenz. Use the following commands to download and install this library.

install this library

git clone https://github.com/adafruit/Adafruit_Python_ADS1x15.git
cd Adafruit_Python_ADS1x15/
sudo python3 setup.py install
cd ..

Now install the required software with the following commands.

Command Lines

sudo pip3 install -U matplotlib
sudo pip3 install -U numpy
sudo apt-get install libatlas-base-dev

Code example

Now download and unzip the code sample.

Command Lines

You can now run the code example with the following command. You will see a graph that records the volume fluctuations.

python3 COM-MIC-ADMP401.py

Command Lines

USAGE WITH THE ARDUINO

Connection

Usage with Arduino Instructions

Code example

Now, copy the following code into your Arduino IDE.

Code example

Click on Upload to run the program. However, make sure that Board and Port are selected correctly under Tools. Under Tools, click on Serial Plotter to display the read-out values of the microphone graphically.

int pin = A0;
int value;
void setup() {
// put your setup code here, to run once:
Serial.begin(9600);
}
void loop() {
// put your main code here, to run repeatedly:
value = analogRead(pin);
Serial.println(value);
}

OTHER INFORMATION

Our Information and Take-back Obligations according to the Electrical and Electronic Equipment Act (ElektroG)

Symbol on Electrial and Electronic Products:
This crossed-out bin means that electrical and electronic products do not belong into the household waste. You must hand over your old appliance to a registration place. Before you can hand over the old appliance, you must remove used batteries and replacement batteries which are not enclosed by the device

Return Options:
As the end user, you can hand over your old appliance (which has essentially the same functions as the new one bought with us) free of charge for disposal with the purchase of a new device.
Small devices, which do not have outer dimensions bigger than 25 cm can be handed in for disposal independently of the purchase of a new product in normal household quantities

Possibility of return at our company location during our opening hours
Simac Electronics GmbH, Pascalstr. 8, D-47506 Neukirchen-Vluyn
Possibility of return nearby
We will send you a parcel stamp with which you can send us your old appliance free of charge. For this possibility, please contact us via e-mail at service @joy-it.net or via telephone.

Information about Package:
Please package your old appliance safe for transport. Should you not have suitable packaging material or you do not want to use your own material, you can contact us and we will send you an appropriate package.

SUPPORT

If any questions remained open or problems may arise after your purchase,we are available by e-mail, telephone and ticket support system to answer these.

E-Mail: service@joy-it.net
Ticket-system: http://support.joy-it.net
Telephone: +49 (0)2845 98469 – 66 (10 – 17 o’clock)

For further information visit our website: www.joy-it.net

Published: 02.08.2020

www.joy-it.net
SIMAC Electronics GmbH
Pascalstr. 8, 47506 Neukirchen-Vluyn

Joy-it logo