NORMAN 65101-11778-C San Clemente Cordless TDBU Shade Instruction Manual

June 10, 2024
NORMAN

NORMAN 65101-11778-C San Clemente Cordless TDBU Shade

Product Information

  • Product Name: N300770-3 65101-11778-C
  • Function: Hardware for installation and maintenance
  • Standard Quantity: Not specified

Usage Instructions

  1. Ensure that you have received all the hardware components specified in your order.
  2. Determine the width (X) required for your installation and maintenance needs.
  3. Using a measuring tape, measure the width (X) of the area where you plan to install or maintain the product.
  4. Compare the measured width (X) with the order width (X) specified in your order.
  5. If the measured width (X) matches the order width (X), proceed with the installation or maintenance process.
  6. If the measured width (X) does not match the order width (X), contact customer support for assistance.
  7. Follow the installation and maintenance instructions provided in your product manual to complete the process.

Getting Started

NOTE:
Prior to installation, please make sure your hands are clean and free from any dirt or oil that could cause damage to the fabric.

Recommended Tools
  • Measuring Tape
  • Pencil
  • Level
  • Screwdriver
  • Power drill (1/4” hex driver and drill bit)

You will need to use the following fasteners for your particular mounting surface.

NORMAN-65101-11778-C-San-Clemente-Cordless-TDBU-Shade-fig-
\(2\)

Check Components/Hardware

Hardware Standard Quantity
Order Width (X) X<27″ 27″ ≦X≦60″ X >60″
Installation Bracket 2 3 4
1 1/4″ Screw for Installation Bracket 4 6 8
Handle 1

Installation

Step 1: Bracket Installation
Use a level to ensure all brackets are in alignment. Proper alignment of brackets will make installation easier.

Measure 4” from both ends of the headrail and mark the bracket location on the mounting surface (applies to both inside and outside mount installation).

Inside Mount
For the shade to operate properly when the inside is mounted, check to make sure there is enough depth clearance for the installation bracket and no obstructions. If you would like your shade to be flush with the wall, the distance from the wall to the center of 1st screw hole needs to be 5/8¨.

Outside Mount

  • Hold the bracket against the wall. Mark a line at every bracket location (shown on the picture).
  • Make sure the lines are level with each other.
  • The min. distance from the wall to the center of 1st screw hole needs to be 5/8¨.

Step 2: Install the Shade
Insert the headrail with an angle facing the window; hook in with the bracket front then push it upward to snap it into the bracket.

Step 3: Handle Installation
For Cordless TDBU, slide the handle onto the plastic piece pre-attached to the rails.

Step 4: Operate the Shade

  • To lower the shade, pull down the bottom rail first before lowering the middle rail.
  • To raise the shade, gently raise the shade on the bottom rail handle to desire height

Uninstall the Shade:
Fully raise the shade that you want to remove. Remove the shade by pushing the latch back. Release the shade by rotating the headrail towards you and lifting upward to unhook the rail from the bracket. See steps 1 to 4.

Cleaning the Shade

Routine cleaning will help maintain the beauty of your shade. The shade can be cleaned by using a soft brush, vacuumed with a low-suction hand-held vacuum, and cleaned ultrasonically (specify that a mild solution must be used and that the headrail should never be immersed in liquid).Spot cleaning is not recommended, but if necessary, dampen a clean cloth with a solution of warm water and mild detergent to dab the spot until it’s gone (do not rub!).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals