NORMAN N301124-C LightGuard 360 System Instruction Manual

June 10, 2024
NORMAN

NORMAN N301124-C LightGuard 360 System Instruction Manual

Product Overview

Inside Mount
Product Overview
Outside Mount
Product Overview

Recommended tools
Recommended tools

  • Power drill
  • Tape measure
  • Screwdriver
  • Level ruler
  • Pencil

Hardware included

Hardware Drawing Usage
1 1/4″ Hexagon screw To install Housing, Bottom Channels, Side Channels,

Swivel Bracket
2″ Flat head screw| Tools| To install safety tension device

Installation of Housing & Side Channels

Installation of the housing

Install the housing to the wall with 1 1/4″ hexagon screws. Check to see if the window header is level. If not, use shims to level the housing.
Inside Mount
Installation of the housing

Installation of the shade

  1. First, insert the control side into the tongue of the bracket for the control side.
  2. Second, press the end plug and insert the end plug into the hole of bracket of the other side.
  3. Third, slide the lock pin in the shade bracket downward into the end plug to prevent the shade from falling.
  4. Finally remove the paper band from the shade.
    Installation of the shade

Installation of the side channels

Note: Make sure the shade functions properly before installing the side channels.

Inside Mount:
Determine the left and right channels by noting that the top of each channel has a plastic top cap while the bottoms do not. The front of each channel contains labels indicating location of screw holes.

Position the top of each channel around the hem bar and clip into the slot of the housing end cap.

Take out the PVC card that stick on the side channel, and then fold it into a U-shape and place into the channel near the screw location labels to reveal each screw hole. Remove the screw location label after side channels are properly installed.
Installation side channels
Installation side channels

Motorized Shades:
For motors with power cord and plug the cord must be routed through the back of the channel. Remove the channel end cap and run the cord through the cutout and behind the channel. Install the side channels as described earlier. For shades with battery wands determine best location for mounting the wand and route cable accordingly.
Motorized Shades

Outside Mount:
First, install the swivel brackets. Make sure that the inner edge of the bend flushes with the window edge, and left brackets face upward and right brackets face downward.
Outside Mount

Determine the left and right channels by noting that the mark of LEFT/RIGHT on the top end cap of the side channels. Put the side channel on the swivel with top aligns bottom edge of the housing and the inner edge flushes with the window edge. And then rotate the bend of swivel brackets down/up to lock the side channels.
Outside Mount

Left Channel
Left Channel

Right Channel
Right Channel

Installation of the bottom channel

Note: Please skip this step if there is no bottom channel.

Inside mount: Place the bottom channel into the side channels and install the screws through the screw holes.
Inside mount

Outside mount: Slide the bottom channel from bottom of the side channel and install the screws through the screw holes, and then align the bottom channel cover with bottom channel and press it into bottom channel.
Outside mount

Installation of the housing cover

Note: Make sure the shade functions properly before installing the housing cover.

For cordless shades, if the shade begins to slide down on its own or it fails to roll up, the issue can be easily fixed by turning the adjustment dial towards “+” to increase the tension. Conversely, if the shade cannot stop at the desired height and tends to roll up by itself, the tension can be decreased by turning the adjustment dial towards the “-”.
The shade must be installed on the brackets when adjusting.
Installation of the housing cover

Installation: Hang the top edge of the housing cover on the housing, and then flip down the bottom of the housing cover into the end cap. Pay attention not to pinch the bead chain / power cord.
Installation
Installation

Installation of safety tension device

For Continuous Cord Loop, properly secure the safety tension device. The bead chain should be fully extended upon installation of the device.

Inside mount:
Mount inside the opening
Installation of safety tension

Mount outside the opening / wall mount
Installation of safety tension

Outside Mount: The safety tension device should be installed outside of the side channels.

Installation of handle

For Cordless shades, slide the handle into the handle base.
Installation of handle

Removal of Housing Cover

Flip down the bottom edge of the housing cover to detach from the housing end cap, and then remove the housing cover from the top.
Removal of Housing Cover

Removal of Shades

  1. Use a tool to push the lock pin on end plug bracket upward.
  2. Use flathead screwdriver to draw back the end plug from bracket.
  3. Finally remove shade from mounting bracket. As shown in drawing.
    Removal of Shades

Swivel Bracket
Dimensions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals