TIEDOWN 73056 Adjustable Mobile Materials Cart Installation Guide
- July 25, 2024
- TIEDOWN
Table of Contents
TIEDOWN 73056 Adjustable Mobile Materials Cart
Specifications
- Load limit: 2,000 lb 5’, 6’, 7’ & 8’ length x 36”wide
- Adjustable cart weight: 256 lbs.
- Shipping weight 2 per pallet : 552 lbs.
- Shipping weight 4 per pallet: 1,150 lbs. All steel, heavy-duty frame with (4) 18” x 8.50” flat-free tires
Product Usage Instructions
Adjustable Mobile Materials Cart
Heavy Duty Adjustable Materials Cart. Adjustable from 5’ to 8’ in length,
36” wide. Heavy Duty 2″ channel frame. 22″ deck height. Drop brake with “T”
handle for easy pulling or towing. Corner slots for rolled goods tubes. Pins
included with attaching cable. Rear hitch pin for the ability to form train of
trailers. Pins included. 2,000 lbs capacity. This model comes with flat free
18” x 8.50” wheels for no down time for flat tires. Flat free tires do not have
a “memory” or flat spot after sitting overnight.
WARNING: This product can expose you to chemicals including Nickel, which is known to the State of California to cause cancer.
For more information go to: www.P65Warnings.ca.gov
Assembly
Lay the roofing cart upside down. Remove the cotter pins and washers from both axles.
Slide each wheel onto the axle pushing backwards until it stops against the wheel stop. Insert washer over the axle rod and secure with the cotter pin.
With the help of a second worker carefully left one side of the cart, flipping over, right side up.
Insert a 6” carriage bolt in the center of rear cart frame, located above the tow slot. Secure the carriage bolt with a wing nut. This bolt is used only in the event of using a second cart for towing.
Position the steering/brake handle in between the front axle steering column. Slide the pull pin through the steering column passing the handle out the opposite side . Secure the pull pin with a cotter pin as shown right. Lower the steering/brake handle engaging the friction brake on the tires as shown right.
Installation
- Insert a 6″ carriage bolt in the center of the rear cart frame above the tow slot and secure it with a wing nut. This bolt is for towing with a second cart.
- Position the steering/brake handle between the front axle steering column and secure it with a pull pin and cotter pin. Lower the handle to engage the friction brake on the tires.
Adjustment Dimension
Remove the (2) 1/2” x 3” carriage bolts and nylock nuts from the front of
the roofing cart. With the brake handle engaged pull the rear of the cart to
your desired length using one of the 5 mounting locations. Insert the 3”
carriage bolt from the top of the cart and tighten the 1/2” nylock nut on the
bottom. Make sure the head of the carriage bolt rest fully on the inner cart
tube. The carriage bolt head should rest below and flush with the outer tube
frame.
- Remove (2) 1/2 x 3 carriage bolts and nylock nuts from the front of the cart.
- Pull the rear of the cart to your desired length using one of the 5 mounting locations.
- Insert a 3″ carriage bolt from the top of the cart and tighten the nylock nut on the bottom, ensuring proper placement.
Towing
In the event multi-able carts are used, one can the towed behind the other
cart. Simply remove the rear carriage bolt and wing nut. Slide the top end of
the steering/brake handle in the slot located on the lower rear axle tube as
show right. Replace the bolt passing through the axle frame and steering
handle, secure with the wing nut.
FAQ
Q: Is this product suitable for outdoor use?
A: Yes, this product is designed for both indoor and outdoor use due to its
heavy-duty steel frame and flat-free tires.
Q: How can I adjust the length of the cart?
A: To adjust the length, follow the instructions provided in the manual, which
involve removing specific bolts and nuts to achieve the desired length.
Safety Products Division
605 Stonehill Drive SW, Atlanta, Georgia 30336
404-344-0000
www.tiedown.com
ISO 9001:2015 Certification
Intellectual Property of TIE DOWN Inc. ©2018 TIE DOWN, Inc.
Instruction #08431 (E1942 Rev. 7/1/24)
404-344-0000
www.tiedown.com
605 Stonehill Drive SW, Atlanta, GA 30336
sales@tiedown.com
References
- P65Warnings.ca.gov
- Tie Down | Custom Manufacturing Solutions for Roofing, Safety, Marine and Much More
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>