HALCYON R742 LED Recessed Luminaire Instruction Manual
- June 10, 2024
- HALCYON
Table of Contents
HALCYON R742 LED Recessed Luminaire
RISK OF FIRE – Required clearance from structural members and building elements Side Clearance to building element (eg timber, joist or Batten) (SCB): 50mm Height Clearance to building element (eg timber, joist or Batten) (HCB): 50mm
CLASSIFICATIONS
Recessed Luminaire Classification:@500mA(CA 135)
CA 135 – building insulation that can safely be continuously exposed to 135 °C allowed to abut the luminaire.
Definition : Can abut the luminaire but NOT cover.
RISK OF FIRE – Required clearance from structural members and building
elements Side Clearance to building element (eg timber, joist or Batten)
(SCB): 50mm
Height Clearance to building element (eg timber, joist or Batten) (HCB): 50mm
Recessed Luminaire Classification: @700mA(NON IC}
NON-IC – A luminaire shall under no circumstances be covered or abutted with building insulation. Definition: Building insulation must not cover or come into contact with any part of the luminaire. For indoor use only. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard. This luminaire must be installed by a qualified Registered Electrician to prevent damage to the luminaire and maintain electrical safety. The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced DO NOT INSTALL THROUGH JOIST, BEAM, RAFTER OR CEILING BATTEN
NOTE : SIDE/HEIGHT CLEARANCE IS MEASURED FROM HEAT SINK
INSTALLATION INSTRUCTIONS
SPECIFICATIONS
- Manufacturer / Supplier Halcyon Lighting Ltd
- Product Code R742
- Product Type LED Recessed Luminaire
- Secondary Voltage 500mA (CA 135) or 700mA (NON IC) Constant Current DC
- Wattage 20W (@500mA) or 28W (@700mA)
- Ingress Protection Rating IP54
DO NOT INSTALL THROUGH JOIST, BEAM, RAFTER OR CEILING BATTEN.
R742@500mA
Classification| | ****
CA 135 – Building insulation that can safely be continuously exposed to 135°C allowed to abut the luminaire. Definition: Can abut the luminaire but NOT cover.
---|---|---
- Side Clearance from heatsink to building element (e.g. timber, joist or batten) SCB: 50mm
- Height Clearance from heatsink to building element (e.g. timber, joist or batten) HCB: 50mm
R742@700mA
**Classification| **| ****
NON IC – A lum na re shall under no
c rcumstances be covered or abutted w th bu Id ng nsulat on.
---|---|---
- Side Clearance from heatsink to building element (e.g. timber, joist or batten) SCB: 50mm
- Height Clearance from heatsink to building element (e.g. timber, joist or batten) HCB: 50mm
Caution : Recessed luminaires and their associated equipment may pose a risk of fire or damage to property if not installed and maintained correctly.
Halcyon Non IC rated luminaires are completely safe to install in sarked
timber ceiling linings with a gauge of less than 20mm. Halcyon accepts no
responsibility if the timber used is not treated correctly and dries out,
crack or warps over time due to the constant low heat from the aforementioned
“Non IC Rated” LED recessed lighting.
This data sheet contains information necessary to ensure compliance with the
New Zealand Electrical Code of Practice for Installation and Maintenance of
Recessed Luminaires and Associated Equipment AS/NZS 60598.2.2:2001
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>