Lumos CONTROLS Cyrus AP AC Powered Wireless PIR Motion and Light Sensor Installation Guide

: June 10, 2024
: Lumos CONTROLS

Table of Contents

WARNING AND GUIDELINES!!!
PRODUCT OVERVIEW
INSTALLATION INSTRUCTIONS
CEILING MOUNT
SURFACE MOUNT
APPLICATION
TROUBLESHOOTING
WARRANTY
COMMISSIONING
LUMOS CONTROLS APPLICATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Cyrus AP
AC Powered Wireless PIR Motion & Light Sensor

Lumos CONTROLS Cyrus AP AC Powered Wireless PIR Motion and Light Sensor -
symbol 1

INSTALLATION AND QUICK START SHEET

WARNING AND GUIDELINES!!!

Read and follow all safety instructions!!
DO NOT INSTALL DAMAGED PRODUCT! This product has been properly packed so that no parts should have been damaged during transit. Inspect to conﬁrm. Any part damaged or broken during or after assembly should be replaced.
WARNING : TURN THE POWER OFF AT THE CIRCUIT BREAKER BEFORE WIRING

WARNING: Risk of Product Damage

Electrostatic Discharge (ESD): ESD can damage product(s). Personal grounding equipment should be worn during all installation or servicing of the unit
Do not stretch or use cable sets that are too short or are of insufficient length
Do not modify the product
Do not mount near gas or electric heater
Do not change or alter internal wiring or installation circuitry
Do not use product for anything other than its intended use

WARNING – Risk of Electric Shock

Verify that supply voltage is correct by comparing it with the product information
Make all electrical and grounded connections in accordance with the National
Electrical Code (NEC) and any applicable local code requirements
All wiring connections should be capped with UL approved recognized wire connectors
All unused wiring must be capped

PRODUCT OVERVIEW

Cyrus AP is a BLE5.2 controllable high bay PIR motion and daylight sensor. This sensor operates on a 90-277VAC input voltage range adopts a PIR sensing technology for
accurate motion detection. It comes with swappable lenses for high-bay and low-bay applications, giving you a maximum mounting height of 14m (46ft) and a maximum detection range of 28m (92ft) diameter. It can be quickly commissioned, conﬁgured, and controlled from any mobile device and can be connected to Lumos Controls cloud for data analytics and conﬁguration management.

Lumos CONTROLS Cyrus AP AC Powered Wireless PIR Motion and Light Sensor -
Fig 1

INSTALLATION INSTRUCTIONS

Wiring the sensor
Turn off the power before wiring and installing the device Power the sensor by connecting the AC Line and Neutral wires from the mains supply to the Line (Black color), and Neutral (White color) from the sensor.

Do’s	Dont’s
Installation should be performed by a qualified electrician	Don’t use

outdoors
Installation shall be in accordance with all applicable local and NEC codes| Avoid input voltage exceeding maximum rating
Turn the power OFF at circuit breakers before wiring| Don’t disassemble the products
Observe the correct polarity of output terminal| –
Specifications| Value| Remarks
---|---|---
Input voltage| 90-277VAC| Rated input voltage
Input current| 9mA@230VAC 15mA@9OVAC| –
Inrush current| 4A|
Surge rating| 4kV|
Operating temperature| 0-80°C (32 to 176°F)| –
Dimensions (Excludes accessories)| 2.3 X 2.5in
(59.8 X 631mm)| Diameter x Height
Net weight (Excludes accessories)| 90g (317oz)| In grams
Case temperature| 70°C (158°F)| _
Case material| ABS Plastic| White
Dimensions (Ceiling mount accessories)
WMAP-CMK-LBL WMAP-CMK-HBL| 3.54 x 4.24in(89.8 x 107.7mm)
3.75 x 4.671n(95.3 x 118.7mm)| Diameter x Height
Dimensions (Surface mount accessories)
WMAP-SMK-LBL WMAP-SMK-HBL| 4.32 x 2.831n(109.8 x 71.8mm) 4.32 x 3451n(109.8 x 88.7mm)| Diameter x Height

REQUIRED TOOLS & SUPPLIES

Lumos CONTROLS Cyrus AP AC Powered Wireless PIR Motion and Light Sensor -
Fig 2

CEILING MOUNT

Mounting sensor on false ceiling
Ceiling mount: Sensor can be installed in the false ceiling using the ﬂush mounted accessory, such as the clips, as given in the steps below

Make a hole of 78mm diameter in the false ceiling where the sensor is to be installed and take out the main supply wires
To open the sensor case, use a pin and press inside the two small holes on both sides of the sensor case and pull upward.
Insert the external wire through the hole above the case. Then connect the external wires with the Sensor Line (Black) and Neutral (White).
Push and ﬁx the case back.
Press and hold the spring clips (on both sides of the device) and insert the sensor into the mounting hole. Release the spring clips so that the sensor will ﬁt in and remain intact.

Note
To remove the sensor from the ceiling, hold and pull the sensor down Interchanging Lens
The High bay and Low bay lens can be interchanged as per requirement. Rotate the lens clockwise to connect to the case and rotate anti-clockwise to dismantle from the case

Rotate the lens anti-clockwise to remove from the case and clockwise to connect to the case

SURFACE MOUNT

Mounting sensor on hard ceilings or on surfaces

Position the sensor mounting base to ﬁx and take out the mains wire through the hole given at the mounting base.
Mount the base on the selected position using screws
Length| Head Diameter| Screw Diameter
---|---|---
38mm| 8.3mm| 3.7mm
Insert the external wire through the hole above the case. Then connect the external wires with the Sensor- Line (Black) and Neutral (White). Termination will happen within the case.
Connect the sensor unit case with the Mount base (that is already ﬁxed in step 2) by rotating the case clockwise.

Lumos CONTROLS Cyrus AP AC Powered Wireless PIR Motion and Light Sensor -
Fig 13

Note
To remove the sensor unit case from the mount base, apply pressure towards ceiling and rotate the sensor case anti-clockwise.

WIRING DIAGRAM

Lumos CONTROLS Cyrus AP AC Powered Wireless PIR Motion and Light Sensor -
Fig 15

APPLICATION

Lumos CONTROLS Cyrus AP AC Powered Wireless PIR Motion and Light Sensor -
Fig 16

TROUBLESHOOTING

Lights are not responding to Motion| Check whether the Sensor is powered ON
Check whether the Sensor association conﬁgured is correct
---|---
Lights are not responding to Daylight| Check whether the Sensor is powered ON Check whether the Sensor association
conﬁgured in the Group is correct
Check whether the Daylight Sensor Settings conﬁgured for the Sensor is correct

WARRANTY

5-year limited warranty
Please ﬁnd warranty terms and conditions
Note: Speciﬁcations may change without notice Actual performance can vary due to end-user environment and application

COMMISSIONING

Once powered up, the device will be ready to be commissioned via the Lumos Controls mobile app, available for free download on iOS and Android. To begin commissioning, click the ‘+’ icon from the top of the ‘Devices’ tab. The app allows you to preset certain conﬁgurations which will be loaded after the device is added. The pre-conﬁgurations made using ‘Commissioning Settings’ will be sent to the devices being commissioned.
Once commissioned, the device will be displayed in the ‘Devices’ tab.

https://knowledgebase.lumoscontrols.com/knowledge

Please visit Help center for more details