Lumos CONTROLS Catron V Wireless Lighting Switch Installation Guide
- June 9, 2024
- Lumos CONTROLS
Table of Contents
Catron V Wireless Lighting Switch
Installation Guide
Catron V
Wireless 5 Button Remote
INSTALLATION AND QUICK START SHEET
WARNING AND GUIDELINES!!!
Read and follow all safety instructions!!
DO NOT INSTALL DAMAGED PRODUCT!
This product has been properly packed so that no parts should have been
damaged during transit. Inspect to confirm. Any part damaged or broken during
or after assembly should be replaced.
WARNING : TURN THE POWER OFF AT THE CIRCUIT BREAKER BEFORE WIRING
WARNING: Risk of Product Damage
- Electrostatic Discharge (ESD): ESD can damage product(s). Personal grounding equipment should be worn during all installation or servicing of the unit
- Do not stretch or use cable sets that are too short or are of insufficient length
- Do not modify the product
- Do not mount near gas or electric heater
- Do not change or alter internal wiring or installation circuitry
- Do not use product for anything other than its intended use
WARNING – Risk of Electric Shock
- Verify that supply voltage is correct by comparing it with the product information
- Make all electrical and grounded connections in accordance with the National
- Electrical Code (NEC) and any applicable local code requirements
- All wiring connections should be capped with UL approved recognized wire connectors
- All unused wiring must be capped
Product Overview
Catron V is a battery-powered switch that configures ON/OFF, intensity, and
Correlated Color Temperature of an individual or group of luminaires.
This compact device is designed for maximum longevity. It is part of Lumos
Controls ecosystem, which includes controllers, sensors, switches, modules,
drivers, gateways, and analytical dashboards.
INSTALLATION INSTRUCTIONS
- Ensure optimal communications with other system components
- Pick a convenient location, perhaps near a door where occupants enter and exit
- Consider the construction materials in the space and remove the obstacles that may interfere with RF signals
Installation Steps
Find a suitable place to fix the wall bracket using screws.
I.Using a level and a pencil, lightly mark 2 small dots to align the top edge
of the mounting plate.
II. Mark the mounting screw drill points and drill holes for the wall anchors
with a 3/16” drill bit and insert wall anchors.
III. Insert the top screw(s) loosely and level the back plate.
IV. Insert the bottom screw(s), and then hand tighten the top screw(s).
V. Attach the wall plate on top of the rocker pad using the two screw holes.
| Do’s | Don’ts |
|---|---|
| Installation should be performed by a qualified electrician | Don’t use |
outdoors
Installation shall be in accordance with all applicable local and NEC codes|
Avoid input voltage exceeding maximum rating
Turn the power OFF at circuit breakers before wiring| Don’t dissemble the
products
Observe the correct polarity of output terminal| _
Specifications
| Specifications | Min | Type | Max | Unit | Remarks |
|---|---|---|---|---|---|
| Input Voltage | _ | 3 | 3. | VDC | CR 2032 battery |
| Frequency Range | 2400 | — | 2484. | MHz | – |
| Tx Power | 6 | 8 | — | dBm | Conductive |
| Frequency Drift(Max) | -25 | _ | 25 | kHz | dF2 |
| Frequency Deviation | ±225 | _ | ±275 | kHz | — |
| Carrier Frequency Offset | _ | 30 | 150 | kHz | _ |
| Tx Current | — | — | 48 | mA | Total current @MaxTx power |
| Rx Current | — | — | 37 | mA | Total current @Rx mode |
| Operating Temperature | 0 | — | 50 | °C | _ |
| Storage Temperature | -10 | _ | 60 | °C | |
| Relative Humidity | _ | _ | 95 | % | Non-condensing |
| Receiver Sensitivity | -86 | _ | -75 | dBm | |
| Dimension | 105x40x12 | _ | – | mm | L x W x H |
| Dimension | 4ki.6xo.47 | _ | — | in | L x W x H |
Required tools & supplies
Device Controls
Pairing
Long press the ON and OFF button simultaneously for 10 seconds to activate
pairing mode.
A green color LED would be lit up when the device is under the pairing mode.
ON/OFF operation
ON and OFF buttons can be used to perform ON-OFF operations.
Intensity operation
Intensity of the luminaires can be
controlled using these Intensity-up and down buttons.
A single click on the Up and down buttons will increase or decrease the
intensity by 10%.
Intensity Operation
CCT operation
CCT operation can be
performed by clicking the CCT mode button.
The device will persist in CCT mode only for 10 seconds after the click.
While in the CCT mode, the CCT up and down buttons can be used to increase or
decrease the CCT by 10%.
Troubleshooting
| Problem | Solution Checklist |
|---|---|
| The rocker pad does not generate a message | Verify the rocker pad is installed |
properly
The linked device does not respond to wireless messages| Check for environment
or range issues
Verify the devices is linked
Check the transceiver connection and the wiring of errors
Check if appropriate devices are linked
Warranty
5-year limited warranty
Please find warranty terms and conditions
Note: Specifications may change without notice
Actual performance can vary due to end-user environment and application
Commissioning
Put the device in commissioning mode by pressing the ON and OFF buttons for 10
seconds. A green LED will lit up when the device goes to commissioning mode.
Choose the zone from the top right corner in the app to which you want to
commission the device. Go to the ‘Devices’ tab in the app. Click on the +
button and choose the option ‘Add device’. Click on ‘Tap here’ and the device
will be listed. Press + button corresponding to the device and the device will
be successfully commissioned.
Please visit – Help center for more details
+1 949-397-9330
All Rights Reserved WiSilica Inc
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>