AQIRYS Magnetar Series Next-Gen Gaming Power Supply User Manual

AQIRYS Magnetar Series Next-Gen Gaming Power Supply User Manual

THANK YOU!

Thank you for choosing the AQIRYS next-gen gaming power supply. The Magnetar series delivers certified 80 PLUS GOLD efficiency, modern features, and outstanding electrical reliability backed up by our 8-Year Warranty. Please take a moment and carefully read this manual before installing your new PSU.

SAFETY ABOVE ALL

The OVP and UVP continuously check the voltages at each rail, kicking in when these voltages surpass or go below a trigger point, shutting down the PSU. The over-current protection is activated when the current in the PSU rails surpasses a certain limit. OCP ensures that the output of the DC voltage rails remains within safe operating limits. The over-power protection kicks in when the power pulled from a PSU exceeds its maximum rated capacity. OPP shuts down the PSU in case the +12V rail becomes overloaded. The over-temperature protection is triggered when the PSU temperature exceeds a specified threshold, shutting down the PSU. Short circuit protection continuously monitors the output rails and immediately shuts down the PSU in the event of an impedance output less than 0.1 ohms, preventing damage or fire caused by short circuits. This feature allows the power supply to turn on and normally operate even if there is no load on its outputs. Offers protection against voltage spikes coming from the mains network, and also against inrush current during the PSU’s start-up phase.

Cables & Connectors

Nominal Output Table

MAX. COMBINED
POWER| 103W| 1000W| 3.6W| 15W
1000W
PROTECTION LEVELS| OPP • UVP • OVP • SCP • NLO • SIP • OCP • OTP

Technical Specifications

• Power: 1000W
• Format: ATX 3.0 Ready
• Efficiency certificate: 80PLUS Gold
• Fan type: 120 mm HDB
• ErP & EuP Regulations Compliant
• Warranty: 8 years

PSU Installation

Cable installation

Install only the necessary cables, carefully following the diagrams below.
Make sure all the connectors are inserted and locked in correctly (you must hear a click and feel the locking mechanism snapping into place when you insert the connector correctly). Do not use excessive force. Incorrect cable installation can permanently damage your hardware!

• Mainboard
  

• CPU
  

• GPU PCle 5.0
  

• GPU PCle 4.0
  

• Storage
  

Installation in the PC case

Bottom of the case

Install the PSU with the fan facing the case ventilation slots.

Top of the case
When installing the PSU on top of the case, we recommended positioning it with the fan facing downwards. If you want to install the PSU with the fan facing upwards, please check that you have at least 50 mm clearance from the top of the case or that the case top has ventilation slots.

Securing the PSU

Secure the PSU with the four screws provided with the product.

Make sure the PSU ON/OFF button is on the “O” position (OFF).

Connecting the hardware

• Make sure all the connectors are inserted correctly (they can only fit one way) and locked in. Do not use excessive force.
• The detachable 4-pin connector of the 24-pin motherboard connector is NOT a “P4” or “+12V” connector. Incorrect usage of the connector can permanently damage your hardware!

Motherboard

Insert the 24-pin connector into the ATX connector on the motherboard

Insert the 8-pin EPS and 4+4-pin EPS connectors (where applicable) into the CPU Power connector(s) on the motherboard.

Graphics card

2a 6+2P PCI-Express 4.0

Insert the 6+2 pin PCI Express connector(s) into the graphics card.

GPU max. power: 150W

GPU max. power: 300W

GPU max. power: 400W

12+4P PCI-Express 5.0

Insert the 12+4 pin PCI Express 5.0 connector into the graphics card until you hear a click.

IMPORTANT

Although it has a smaller form factor, the PCI Express 5.0 (12VHPWR) cable contains more wires than the previous PCI Express cable, which leads to smaller tolerances for handling it and its connectors. When installing the PCI Express 5.0 (12VHPWR) cable, we strongly advise following the below recommendations:

• All connectors must be correctly inserted, locked in, and tight to avoid any issues (you must hear a click and feel the locking mechanism snapping into place when you insert the connector correctly).
• DO NOT bend the cable in any direction once it is plugged into place.
• DO NOT bend or apply force to the cable too close to the connector.
• If necessary, the cable should be bent before plugging it into the power supply and GPU. Any bend of the cable (an angle of 45° or 90°) should occur at least 35 mm away from the connectors. When bending the cable, you can use a gentle heat source (hair dryer) to carefully heat the area where you wish to make the bend. The power supply warranty is void if the unit is rendered defective due to not following the recommendations for cable installation.

Storage devices and accessories

Insert the SATA connector into compatible storage devices (SSD, HDD, ODD) and various accessories (fan controller, etc.).

Insert the 4-pin MOLEX connector into compatible storage devices (HDD, ODD) and various accessories (fan controllers, fans, etc.).

PSU power-up

Connect the AC power cord to the PSU. Plug the AC power cord into the wall outlet. Switch the PSU ON/OFF button to the “I” position (ON).

Attention

Warnings

• DO NOT open the PSU. High voltage inside! Warranty is VOID if cover is removed.
• DO NOT insert objects into the PSU or fan grill.
• DO NOT obstruct the ventilation areas of the PSU in any way.
• Warranty void if seal is broken or missing!

REGULATORY

• Unauthorized repairs or disassembly of the product will void the warranty and may cause its damage.
• This product is safe and complies to EU requirements. (compliant with directive EMC (2014/30/EU) LVD (2014/35/EU))
• This product is manufactured conforming with the European RoHS standard. (compliant with directive RoHS 2.0 (2015/863/EU))
• Using the WEEE symbol (the crossed-out bin) indicates that the electrical and electronic equipment inside the package can be recycled. When recycling waste properly, you protect the environment and people health. Segregated household waste collection, aids recycle materials and components used for the production of this device. For detailed information about recycling, please contact your retailer or a local authority.

If you encounter errors or any other problems with the product don’t hesitate to contact us.

Disclaimer.
All efforts have been made to ensure accuracy of all information provided in this document. PC-coolers SRL assumes no liability, expressed or implied, for any damage(s) occurring to your system’s components or other devices as a result of any mistake or omission during power supply installation or removal, or due to any defect or failure of the product itself.

support@aqirys.com

Scan Me ( Product Page)

Scan Me ( Follow Us)

AQIRYS®. All rights reserved. AQIRYS® name and logo and all other related products, service names, and design marks are trademarks or registered trademarks of PC-coolers SRI. All other brand names and trademarks are the property of their respective owners. Specifications and design are subject to change without notice due to product improvement.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>