AQIRYS Lyra Wireless Headset User Manual
- June 9, 2024
- AQIRYS
Table of Contents
LYRA
QUICK START GUIDE
Transmitatorului Wireless
Headset And Wireless Receiver Overview
- LED Indicator
- On / Off
- Answer Call / End Call
- Play / Pause
- Volume + / Next Track
- Volume – / Previous Track
- Vibration Switch
- Micro-USB Charging Port
- Internal Microphone
- 3.5 mm Audio Port
- Ext. Mic Mute Button
- Ext. Mic Boom Arm
- RGB Lighting System
- LED Indicator
- Multi-function Button
- USB Connector
Headset Specifications
Supported profiles | A2DP/AVRCP/SMP/HFP |
---|---|
Operating distance | 8 – 10 m |
Audio impedance | 32Ω ± 15% |
Audio driver size | 40 mm |
Vibration impedance | 16Ω±15% |
Vibration driver size | 30 mm |
Vibration impedance | 20 Hz – 20 KHz |
Sensitivity | 108 ± 3dB @ 1 KHz |
Microphone sensitivity | -42 ± 3dB |
Charging voltage | DC5V |
Charging current | 800 mA |
Operating voltage | 3.7V |
Operating current | 26 – 120 mA |
Wireless Receiver Specifications
Interface | USB 2.0 |
---|---|
Signal-to-Noise Ratio | >90dB |
Frequency Range | 20 Hz — 20 KHz |
Transmission Range | 10 m |
Operating voltage | 5V |
Operating current | 14 — 27 mA |
Packing List
- Wireless Headset
- Removable Microphone
- Micro-USB charging cable
- Audio Cable
- User Manual
- Wireless Receiver
- Audio Splitter
- Hardcase
Headset Connection
Bluetooth®
Long press the button , the headset will initialize, and then the LED will
flash blue and green; the headset is now in Pairing mode.
Activate the Bluetooth connection on your terminal, search for the“AQIRYS Lyra
Wireless Headset” device and choose to connect to it.
If the pairing is completed successfully, the headset LED will be lit solid
blue.
During music playback, the LED flashes blue.
Note: the RGB lighting system will turn on automatically when the headset
is turned on; the lighting can be switched off later via the buttons on the
headset.
Wireless
-
Connect the USB receiver to an available port on your device.
The required driver will be installed automatically, and the device will be displayed with the name “AQIRYS Lyra Wireless Headset”.
The receiver will enter in Standby mode, and the LED will be lit solid red. -
Turn on the headset and wait for it to enter Pairing mode; long-press the button on the wireless receiver for 2 seconds to switch it to Pairing mode; The receiver LED will flash green.
-
The headset and the receiver will connect automatically, and the receiver LED will be lit solid green.
Subsequent Connections
After the first use, the pairing information will remain saved on your
equipment, and the subsequent connections between the receiver and the headset
will be made automatically.
Wireless Receiver Power On/Off
The receiver is automatically turned on and off when connected and
disconnected to the USB port.
Wired
When the headset is connected using the audio cable, the wireless
functionality is turned off automatically.
In wired mode, you can listen to music, use the internal or external
microphone, activate-deactivate the vibration effects.
Note: wireless functionality can only be activated after disconnecting
the audio cable!
LED Indicator Description
Headsets
Pairing Mode | LED flashes blue and green |
---|---|
Power On | LED is solid blue; LED flashes blue when music is playing |
Standby Mode | LED is solid blue |
Low Battery | LED flashes blue 3 times per second |
Vibration Mode | Vibration ON: LED is solid white |
Charging Mode | The battery is charging: the LED is solid red. Charging |
complete:LED is off.
Receiver
Standby Mode | LED is solid red |
---|---|
Pairing Mode | LED flashes green |
Connection Succeeded | LED is solid green |
Auto Disconnect and Reconnect
The headset will automatically disconnect when it is out of the effective
operating distance.
If returned to range within less than 5 minutes, the headset will
automatically reconnect to the phone.
Otherwise, after 5 minutes, the headset will automatically turn off.
Basic Key Operation
Turn Headset On
Long press the button ,the headset is initialized after the LED lights up blue
for 3 seconds, then enters Pairing mode.
Turn Headset Off
Long press the button ,the LED flashes blue and green for 2 seconds, then
turns off, and the headset turns off.
Volume Adjustment
Short press the button or the button to control the volume.
Track Selection
Long press the button to skip to the next song.
Long press the button to skip to the previous song.
Play/Pause/Phone Call
Pause: short press the button while playing a song.
Play: short press the button to continue playing the song.
Answer a call: short press the button when receiving a phone call.
End call: short press the button at the end of the phone call.
Reject call: long press the button when receiving a phone call.
Redial: press the button twice to call the last number in the call record.
Vibration Effects
After turning the headset on, slide the vibration switch down to activate
the effects (the LED will illuminate solid white). The headset will vibrate
depending on the bass level: the higher it is, the stronger the effects. Slide
the switch up to turn off vibration effects; the LED will stop illuminating
white, and the headset will return to standard operation.
RGB Illumination
The RGB lighting system will turn on automatically when the headset is
turned on. If you want to turn off the lighting to conserve battery power, or
for any other reason, shortly and simultaneously press the and buttons. The
lighting can be reactivated following the same procedure.
Note: The lighting will not work while the headset is charging or used
with the audio cable.
External Microphone
For better communication performance, the headset is equipped with an
external and flexible microphone. During a call, the external microphone can
be temporarily muted by shortly pressing its Mute button. When the microphone
is temporarily muted, the headset will beep. To resume the call, press the
Mute button again.
Battery Charging
When the battery level is low, it can be charged in about 3 hours using the
USB charging cable.
During charging, the headset will turn off automatically, and the LED
indicator will illuminate solid red. When the battery is fully charged, the
LED indicator will turn off.
Battery Level
When the headphones are connected to an IOS device, the battery level will
be displayed in the upper right corner of the screen.
Depending on the usage configuration, the headset will warn about the battery
level and auto power-off as follows:
- Maximum volume, vibration off, lights off – headset will turn off after 4 times low-battery warning (20%, 15%, 10%, 5%).
- Maximum volume, vibration off, lights on – headset will turn off after 4 times low-battery warning (20%, 15%, 10%, 5%).
- 50% Volume, vibration on, lights on – headset will turn off after 4 times low-battery warning (20%, 15%, 10%, 5%).
- Maximum volume, vibration on, lights on – headset will turn off after 2 times low-battery warning (20%, 5%).
Recommendation
- You can use 5V / 1A or 5V / 2A chargers to charge the battery; higher voltages can damage the headset.
- If more than 3 months have passed since the last use of the headset, please charge them before use.
- If you do not use the headset for an extended time, we recommend running a complete charge cycle of the battery every 3 months to preserve it.
- Before the first use, we recommend running a complete battery charge cycle.
Warnings
- Keep the headset in environments without extreme temperatures; do not expose to direct sunlight.
- Keep the headset away from fire and hot objects.
- Keep the headset dry; avoid exposure to humid environments; do not immerse in liquid.
- Do not try charging methods other than using the supplied USB cable.
- Do not disassemble, repair or modify the headset.
- In case of physical damage like bending, deformation, corrosion, contact the authorized service.
- In case of other issues such as abnormal odor, very high operating temperature, abnormal changes in color or shape, stop using the headphones immediately and contact the authorized service.
- If the battery is replaced incorrectly, there is a risk of explosion. The battery can only be replaced with the same type or equivalent. Please contact the authorized service.
- This product is not a toy. Children under the age of 14 may use the product under parental supervision.
WARNING: Permanent hearing damage can occur if the headset is used at high volumes for extended periods of time.
Support
If you encounter errors or any other problems with the headsets don’t hesitate
to contact us.
support@aqirys.com
https://www.instagram.com/aqirys/
https://www.aqirys.com/category/lyra
WARNING: Permanent hearing damage can occur if the headset is used at
high volumes for extended periods of time.
© AQIRYS ® . All rights reserved. AQIRYS ® name and logo and all other related
products, service names, and design marks are trademarks or registered
trademarks of PC-coolers SRL.
All other brand names and trademarks are the property of their respective
owners.
Specifications and design are subject to change without notice due to product
improvements.
- Unauthorized repairs or disassembly of the product will void the warranty and may cause its damage.
- This product is safe and complies to EU requirements. (compliant with directive EMC (2014/30/EU))
- This product is manufactured conforming with the European RoHS standard. (compliant with directive RoHS 2.0 (2015/863/EU))
- Using the WEEE symbol (the crossed-out bin) indicates that the electrical and electronic equipment inside the package can be recycled. When recycling waste properly, you protect the environment and people health. Segregated household waste collection, aids recycle materials and components used for the production of this device. For detailed information about recycling, please contact your retailer or a local authority.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>