PR-45552-TTS Pressure Injectable Arrowg+ard Blue Advance Two-Lumen PICC pre-loaded with Arrow VPS TipTracker Stylet Instruction Manual
- June 4, 2024
- Arrow
Table of Contents
PR-45552-TTS Pressure Injectable Arrowg+ard Blue Advance Two-Lumen
PICC pre-loaded with Arrow VPS TipTracker Stylet
Instruction Manual
Contents
1: Two Lumen TaperFree® Catheter with Arrowg+ard Blue Advance®
Antimicrobial/Antithrombogenic Protection1: 5.5 Fr. (1.88 mm OD) x 55 cm,
Pressure Injectable, Blue FlexTip®, Arrow® TipTrackerTM Stylet and T-Port
Connector
1: GlideThru TM Peel-Away Sheath: 5.5 Fr. x 2-3/4″ (7 cm) Radiopaque over 5.5
Fr. Dilator
1: Spring-Wire Guide, Nitinol, Marked: .018″ (0.46 mm) dia. x 17-3/4″ (45 cm)
(Straight Soft Tip on One End – Straight Stiff Tip on Other) with Arrow
Advancer 1: Safety Introducer Needle: Echogenic 21 Ga. x 2-3/4″ (7 cm) TW
1: Introducer Needle: Echogenic 21 Ga. x 2-3/4″ (7 cm) TW Syringe: 10 mL Luer-
Lock Dust Cap: Non-Vented
1: SecondSiteTM Adjustable Hub: Fastener
1: SecondSiteTM Adjustable Hub: Catheter Clamp
1: SharpsAway® Disposal Cup
1: SharpsAway® II Locking Disposal Cup
1: Catheter Trimmer
1: Safety Scalpel: #11
1: Patient ID Card
• Patient Information Booklet
• Paper Tape Measure
1: Tourniquet
1: Foam Electrodes (3 per pack)
1: Dressing: STATLOCK®2 Catheter Stabilization Device
1: Equipment Cover: 13 cm x 244 cm (5″ x 96″)
1: T-Piece Cover
1Licensed under US Patent No. 7,329,412.
2A registered trademark of C. R. Bard, Inc.
All components are CE 2797 unless otherwise
Not made with natural rubber latex.
Store below 25°C (77°F). Avoid excessive heat above 30°C (86°F).
Contraindications: The Pressure Injectable Arrowg+ard Blue Advance
antimicrobial/anti-thrombogenic catheter is contraindicated:
- for patients with known hypersensitivity to chlorhexidine
- in the presence of device-related infection in the intended insertion vessel or catheter pathway
- in the presence of thrombosis in the intended insertion vessel or catheter pathway
| Priming Volume* (mL)| Gravity Flow Rate† (mL/hr)| Pump Flow Rate†† (mL/hr)|
MAX Pressure Injection Flow Rate** (mL/sec)
---|---|---|---|---
Distal ( 18 Ga. )
Proximal ( 18 Ga. )| 0.49
0.50| 238
244| 3020
2970| 5
5
- Priming volumes are approximate and are done without accessories.
†Flow rate values are approximate and are determined using deionized water at 100 cm head height.
††Pump flow rates are determined at a maximum pump pressure of 10 psig and represent approximate flow capabilities.
** Pressure injection flow rates are determined at the injector pressure setting of 300 psi maximum using media of 11.8 centipoise viscosity, with 152 cm pressure tubing.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>