BN-LINK Wireless Remote Control Socket User Manual
- June 10, 2024
- BN-LINK
Table of Contents
BN-LINK Wireless Remote Control Socket
Product Information
The product complies with part 15 of the FCC Rules. It is designed to not cause harmful interference and must accept any interference received, even if it causes undesired operation. Any changes or modifications to the product that are not approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Product Usage Instructions:
When using the product, ensure that it is not causing any harmful interference to other devices in the vicinity. If you experience any interference with the device, ensure that it is still accepting the interference and not causing any undesired operation. Any changes or modifications to the product should not be made without express approval from the party responsible for compliance. Failure to comply with these instructions could result in voiding the user’s authority to operate the equipment.
PRODUCTS VIEW
FEATURES
- Easily controlled by the remote control from up to 100 feet in line-of-sight.
- Separate on and off buttons on the remote control.
- Outlets will remain powered off after a power outage to save energy.
- Power output up to 1200W at 120V(60Hz).
- Low power consumption, reduces energy use and extends product life by up to 15%.
- Manual pairing and unpairing.
SETUP
- Install one 12V/23A battery in the remote control’s battery compartment, making sure the polarity of the battery is correct.
- Plug each outlet switch into a socket and plug a device or appliance into each outlet.
- Press the on/off buttons for the respective channel on the remote control to operate the outlet switch.
NOTES
-
Regularly change the battery in the remote control for best performance. If you find the outlet switches are not responding or the LED indicator on the remote control becomes dim, the battery should be replaced. Always dispose of old batteries properly with consideration for the environment.
-
Make sure the battery and outlets are installed firmly and correctly for safe operation.
-
These outlet switches are for indoor use only. Avoid exposure to high temperature sources, strong sunlight and moisture.
The outlets are best used in air as with good air circulation. -
Do not exceed the maximum load current of 1 OA(Approximately 1200W).
TECHNICAL DATA
- Voltage ……………………………. 120V~60Hz
- Max.power ……………………….. 10A 1200W
- Transmission frequency …….. .433.92MHz
- Remote battery ……………………. 12V (23A)
PROGRAMMING THE OUTLETS
Notes: The outlets are pre-programmed for immediate use, but the
configuration can be customized to meet your needs.
To program a remote control transmitter and outlets switch reæiver:
- Remove the outlet receiver from the power socket, then plug the outlet receiver back into the power socket.
- Press and hold the “Learning & ON/OFF” button till the indicator start to flash.
- Release the “Learning & ON/OFF” button, press and hold the corresponding “ON” button on the remote until you hear a “click”.
- The indicator will stop flashing indicating that pairing is successful.
RESETTING AN OUTLET
Should you wish to unpair an outlet receiver from the remote, or if your outlets are unresponsive to the remote, the outlets can be reset following below steps.
- Remove the outlet receiver from the power socket.
- Press and hold “Learning & ON/OFF” button on the outlet receiver.
- While still holding the button, plug the outlet receiver to a power socket and wait to see the indicator to flash.
- When the indicator stops flashing, you may release the button, and the reset process is now complete.
- You may program the outlet after resetting.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>