arte confort GALA IP44 Outdoor Ceiling Fan Instruction Manual

arte confort GALA IP44 Outdoor Ceiling Fan

THANKS FOR TRUSTING IN ARTECONFORT

Congratulations, you have just purchased an Arteconfortcei ling fan: cutting edge technology combined with the highest energy efficiency.

WARNING
Read this instruction manual carefully before beginning installation and save it for future reference. In case of transfer of the device, you must also give this instruction manual to the corresponding person.
While using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury.

CAUTION

• The product must only be installed by an authorized electrician and in compliance with local, regional and state electricity regu lations.

• Check if the electricaI specifications of this device are compatible with your installation.

• Turn off the power before installing or repairing the fan.

• The fan must be properly grounded to avoid the risk of electric shock.

• Use and unauthorized technical modifications could suppose a risk of injury.

• The fan must be connected to a 230V SOHz power supply.

• Do not connect the fan motor to a current dimmer. It could give unsatisfactory performance (engine humming) and cause engine damage.

• Be caref ul while working nea r the spInn 1ng b lades.

• Never connect the fan to a power point but to the ceiling itself.

• The fan must be installed so that the blades are at least 2,3 meters above the g round.

• The fan must be hung from a structure capable of supporting a weight of at least 50 kg. The fixture must be able to support the weight of the fan in motion and should not wobble or loosen.

• Make sure that the blades do not come in con tact with any object at the installation site. Always leave a minim um clearance of 50cm from the tip of the b lades to the wall or ceiling.
  Keep in mind that the larger t his space, t he better the fan’s air flow w ill be.

• The fan must not be started in a room with a gas appliance running at the same time.

• This device can be used by children aged 8 years and above and o f people with reduced physical, sensory or mental abilities or lack of experience and knowledge if they are supervised or instructed a bout the use of the device safely and understand the risks involved. As well as clean ing and maintenance of the device.

• Children should not p lay w ith the device.

• To reverse the d irection of the blades, do it while moving.

• Do not insert any object into the fan b lades wh ile they are rota t ing. Th is can damage them and alter the balance of the fan and the device can fall down.

• After the fan is fully installed make sure all fasteners a re securely fastened to prevent any wobbling or falling of the machine.

• The instructions and safety regulations in this manual cannot prevent al l conditions and situations that may occur. For obvious reasons, this manual cannot include factors such as caution and care. These factors must be assumed by who instal ls, maintains, uses and enjoys the product.

BEFORE INSTALLATION

Open the box ovoiding the use of blodes or “cutters” to avoid scratching the fan components. Unpack the parts handling them carefully so that they do not bend or scratch, and place the motor on a cloth or a soft surface to prevent damage (you can also use the anti-shock foam on the box for this purpose). Never support the motor sideways.
It is advisable to mount the fan on the floor or a surface large enough so that no component falls. Identify all parts before beginning assembly.

TOOLS NEEDED

*Not included. It is recommended that the screwdriver be magnetized.

MAINTENANCE

• Over time and due to the natural movement of the fan, some connections may come loose. Check the support connections, brackets and attach the blades twice a year, and make sure they are firm.
• Clean the appliance regularly to maintain its appearance as new. To do this, use a soft, lintfree cloth to avoid scratching the finish. Never use water, because it could damage the motor or the wood of the blades.
• It is not necessary to grease the fan, since the motor bearings permanently contain lubricant.

WARRANTY

You can check the warranty for this product on its corresponding page at the end of this manual.

ENVIRONMENT

Do not throw electrical appliances into the household waste, use selective collection facilities. Consult local authorities for more information.
If electrical appliances are deposited in landfills, hazardous components can seep into groundwater and enter the food chain, damaging health and well- being.
Thanks for taking care of the environment.

This product contains a light source of energy efficiency class F – (EU) 2019/2015

PROBLEM SOLVING

Before carrying out the checks detailed below, the fan must be without power supply.

1. The fan does not start
   ● Replace the remote control batteries if they are exhausted or not suitable.
   ● Check that there are no nearby devices that may be causing interference with the remote or reducing signal reception.
   ● Resynchronize the remote control.
   ● Check that the electrical connections are correct (must be carried out by a licensed electrician)
   ● Check fuses and switches, that the installation has voltage and it reaches the fan.

2. The fan doesn’t start but the light does.
   ● With the fan off, check with your hand that the blades turn freely.

3. The fan makes excessive noise while rotating
   ● Allow a slight separation between the canopy and the ceiling, preventing them from touching directly.
   ● Check that the fixing screws of the blades, the fixing screws to the roof, the stem and the fastening elements are correctly tightened.
   ● If you replaced the original remote control or receiver, reinstall the supplied ones along with the fan.

4. The fan wobbles
   ● Check that the fixing screws of the blades, the fixing screws to the roof, the stem and the fastening elements are correctly tightened.
   ● Check that the blades are not deformed and follow the blade balancing instructions detailed in this manual.

5. The fan does not give air or the air flow is insufficient
   ● Check that the blades are not mounted backwards.
   ● Check that the blades rotate in the correct direction (Summer/ Winter).
   ● Avoid nearby objects that may impede air circulation.
   ● Verify that the diameter of the blades of your fan is sufficient for the area of the room in which it is installed.

6. The light does not turn on
   ● Check the bulb is not blown, otherwise replaces it with a new one.
   ● If your fan has LED light included, check the connections are properly fixed according to the instruction manual.

COLOR TEMPERATURE MEMORY

The fan has color temperature memory of the light. This function allows you to maintain the same color temperature when the fan light is turned on again.
To change the color temperature of the light press. the button indicated with the color of each color temperature.
When you turn the light off and turn it on again it will keep the selected temperature.

REMOTE CONTROL

WINTER/SUMMER MODE (FIR)
Reverse the direction of rotation of the blades to change to summer mode or winter mode.
LAMP ON/OFF (LIGHT ON/OFF)
Turns the light and synchronization on or off (see section “Control synchronization”).
FAN ON/OFF (FAN ON/OFF)
Turn the fan on or off.
SPEED REGULATOR
Increases or decreases the turning intensity of the blades.
LIGHT INTENSITY REGULATOR
Increase or decrease the intensity of the light.
LIGHT TEMPERATURE
Change the color temperature of the light.
PROGRAMMING
Sets the hours of fan operation (2 or 4 hours).
BREEZE MODE
Activate the breeze mode that alternates smoothly between soft and fast speeds (from speed l to 3) to create a greater sensation of comfort.
To activate the breeze mode, activate the fan using the “ON/OFF” button on the fan and then press the “Breeze mode” button.
For cancel breeze mode press the “Breeze mode” button again, the fan will return to the rotation speed selected before the breeze mode. You can also press the “ON/OFF” button of the fan to completely stop the rotation of the blades, when you turn it on again it will not remember the breeze mode, activating at the previously selected rotation speed.

*The remote control is synchronized from the factory, you only need to re-synchronize it if the synchronization has been lost, if you purchased a new one or want to control several fans with a single remote.

REMOTE CONTROL SYNCHRONIZATION

synchronization, purchased a new one, want to control several fans with a single remote, or the fan does not respond to the remote control orders while it is running.

A REMOTE CONTROL TO A NEW FAN

1. Cut the current Be sure to cut off the current until the fan stop and wait 30″

2. Restore the current
   Past 30″ re-establish the current.

3. Synchronize the remote control
   Within 10 seconds, press the synchronization button c during 3 seconds until you hear the signal. Control range: 8-l0m.

A REMOTE CONTROL TO VARIOUS FANS

1. Cut the current
   Be sure to cut off the current until all fans stop and wait 30″
   

2. Restore the current
   Past 30″ re-establish the current.
   

3. Synchronize the remote control
   Within 10 seconds, press the synchronization button “ON/OFF light” on each fan during 3 seconds until you hear the signal. If they are within a radius of less than l0m (control range: 8-l0m), all will synchronize at the same time.

A REMOTE CONTROL TO A FAN

(Example for two fans, applicable to a larger number of fans)

1. **Cut the fan A current***
   Be sure to cut the fan A current (the one we want to remove the synchronization) and wait 30″.
   

2. **Cut the fan B current***
   Be sure to cut off fan B (the one we want to synchronize) and wait 30″.
   

3. Restore fan B current
   When you restore the fan B and within 10 seconds, press the synchronization button “ON/ OFF light” during 3 seconds until you hear the signal to synchronize remote control B with fan B.
   

4. **Cut the fan B current***
   Be sure to cut the fan B current and wait 30″.

5. Restore the fan A current
   When you restore the fan A and within 10 seconds, press the synchronization button “ON/ OFF light” during 3 seconds until you hear the signal to synchronize remote control A with fan A.

6. Repeat the steps
   Repeat steps with each fan you have and want to individualize its remote control.
   
   *To cut the current you can press the individual fan switch. If there is not, disconnect the quick connect cables from the Fan.

GALA

SYNCHRONISATION OF TWO REMOTE CONTROLS TO ONE FAN

TWO REMOTE CONTROLS TO ONE FAN

1. Cut the current
   Be sure to cut off the current until the fan stop and wait 30″.

2. Restore the current
   Past 30″ re-establish the current.

3. Synchronize the remote control A
   Within 10 seconds, press the synchronization button c during 3 seconds until you hear the signal. Control range: 8-l0m.
   

4. Cut the current
   Be sure to cut off the current until the fan stop and wait 30″.

5. Restore the current
   Past 30″ re-establish the current.

6. Synchronize the remote control B
   Within 10 seconds, press the synchronization button c during 3 seconds until you hear the signal. Control range: 8-l0m.

*It is not possible to synchronise more than two controllers to one fan.

GENERAL GUIDE

PARTS OF A FAN

SCREW GUIDE

SCREWS FOR THE OOF

Screws for the roof
Ceiling screw plugs
Washer for ceiling screw

SCREWS FOR BLADES

• Screw for wood blades

• Screw for blades with washer

• Screw for blades

• Paper washer for blade screw

INSTALLATION INSTRUCTION

| Light cover| PLAGALA
| LED module| LEDGALA
| Remote control| tv1ANGALAONLY
| Driver| CONGALAONLY

GALA

CONTROL MED/ANTE APP
CONTROL BY APP
CONTROLE VIA APPs

1. DOWNLOAD APP
   You will need to download the “Fan Lamp Pro” app to your mobile device (smartphone) from the mobile application distribution platform corresponding to the operating system of your mobile device.

   
   
   

2. SYNCHRONISATION OF FAN LAMP PRO APP
   I. Open application after installation Open the application once it has been installed on the smartphone.
   2. Activate Bluetooth Activate Bluetooth from the APP or from your mobile phone’s settings.
   3, Add device On the main screen of the application, press the button with the “+· symbol to add a new device.
   4, Name the device Enter the desired name of the new device to be added.
   5. Synchronise device
   Once the device has been created, access its features and link it using the “Synchronise button·.
   To synchronise the device, turn the fan power off and back on again. Press this button within 5 seconds after the device is connected to the power. If the device flashes or beeps, the mobile has been successfully paired.
   

3. SYNCHRONISINGMULTIPLE MOBILE PHONES If you want to synchronise two or more smartphones to one ventilator, follow the steps below:
   SMARTPHONE A
   Open application
   Open the application once it has been installed on the smartphone and synchronised the fan.
   Activate Bluetooth
   Activate Bluetooth from the APP or from your mobile phone settings.
   Synchronisation
   Select “My QR code” from the dropdown menu to display the QR code to be scanned by smartphone B.
   SMARTPHONE B
   Open application
   Open the application once it has been installed on the smartphone.
   Activate Bluetooth
   Activate Bluetooth from the APP or from your mobile phone settings.
   Synchronisation
   Select “Scan QR code” from the dropdown menu and scan the QR code on smartphone A.
   Repeat these steps to synchronise more smartphones.

When copying the data, the previous fan profile will be deleted.

4. BUTTONS
   I.Cold light
   When clicked, the cold light will be switched on, with maximum brightness.
   2. Warm light
   When clicked, the warm light is switched on at maximum brightness.
   3. Neutral light
   Clicking switches on the neutral light at maximum brightness.
   4. Night mode light
   Neutral light at 10% of maximum brightness.
   5. Direct direction
   Summer mode, the blades rotate clockwise.
   6. Synchronisation
   To ensure that the application controls the device correctly.
   7. Timer
   You can time the operation of the fan.
   8. Breeze mode
   Emits wind in a more natural way.
   9. Reverse direction Winter mode, the blades rotate counterclockwise.
   10. ON/OFF light
   11. OFF fan and light
   12. ON/OFF fan ,. l 9 ·2 ,.
   

5. DESYNCHRONISATION
   To de-synchronise the device, turn off and on again the power to the fan. Within 5 seconds, press the “Desynchronise button” on the main screen.
   

www.arteconfort.com
ARTECONFROT HOTEL S.L.
Ctra. Andalusia, 6
45224 Sensna Nuevo Toledo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>