CENTEK CT-1772 Chest Freezer Instruction Manual

CT-1772 Chest Freezer

Product Information: CT-1772, CT-1773 Chest Freezer

• Model Numbers: CT-1772, CT-1773
• Type: Chest Freezer
• Instruction Manual Included
• Temperature Range: -15 to 0 degrees Celsius
• Refrigerant: R600a (39 or 45 grams)
• Dimensions:
  • CT-1772: 545 x 476 x 835 mm
  • CT-1773: 635 x 556 x 835 mm
• Climate Class: N/SN/ST/T
• Voltage: 220-240V ~50Hz
• Power Consumption:
  • CT-1772: 0.6 kWh/24h
  • CT-1773: 0.7 kWh/24h
• Net Weight:
  • CT-1772: 41 kg
  • CT-1773: 46 kg
• Gross Weight:
  • CT-1772: 46 kg
  • CT-1773: 52 kg

Product Usage Instructions

1. Plug the chest freezer into a grounded electrical outlet.

2. Adjust the temperature control to set the desired temperature.
   The temperature range is -15 to 0 degrees Celsius.

3. Wait for the chest freezer to reach the set temperature before placing food or drinks inside. This may take several hours.

4. Arrange food or drinks inside the chest freezer according to your preference.

5. To defrost the freezer, unplug it and remove all items. Allow the ice to melt naturally or use a soft cloth to speed up the process. Do not use knives, metal scrapers, or other sharp objects to remove ice as this can damage the interior of the freezer.

Note: For further information, please refer to the instruction manual included with the chest freezer.

DEAR CUSTOMER!
Prior to operating the appliance, please carefully read the present manual which contains important information regarding its proper and safe operation. Take care not to lose the present manual. The manufacturer will not be responsible for any damage resulting from improper use of the appliance or from non-observance of the instructions and provisions of the present manual, as well as from attempts by unskilled persons at repairing the appliance. Should You decide to transfer the appliance to another person, please pass the present manual over along with it.
The chest freezer is a home appliance and is not designed for industrial applications!

PURPOSE OF THE APPLIANCE
For food cooling and/or freezing in a heat-insulated chamber at low temperature.

SECURITY MEASURES

In order to avoid situations that are dangerous to life and health, as well as premature failure of the device, it is necessary to strictly observe the following conditions:

• ATTENTION! Non-observance of the following safety instructions can cause accidents.

• Use only 220-240V, 50Hz power supply systems.

• Avoid using socket adapters and extension cables for power connection.

• Do not store volatile, flammable or explosive substances, such as ether, ethanol, gasoline, etc. in the freezer.

• Do not place heavy objects or spill water on the freezer.

• If you notice any unusual noise, smell, smoke or any signs of damage during operation, immediately disconnect the appliance from power supply and contact a maintenance service.

• Avoid damaging the power cable:

• No power cable replacement is allowed.

• Do not place heavy objects on the power cable.

• Keep the power cable at a safe distance from heat sources.

• Disconnect the appliance from power supply by puling the plug and not the cable.

• Do not connect too many appliances to the same power supply circuit as this can become the cause of a fire.

• Wipe the internal surface of the appliance with a soft cloth dampened with warm water.

• Do not touch the internal walls of the appliance and the foods stored inside with wet hands.

• It is necessary to maintain air circulation around the appliance during its operation. The minimum distance between the appliance and adjacent walls should be 10 cm.
  Before connecting the appliance to power supply let it stand up-right for 2 hours. This will reduce the probability of cooling system malfunctions caused by improper transportation.
  The refrigerant used in the appliance is charged into it at the factory using special equipment. Do not allow refrigerant circulation piping to get damaged.

• The refrigerant escaping from the piping can ignite or harm your health. If the refrigerant circuit is damaged, avoid using open flames or any other sources of ignition and ventilate the room where the freezer is installed for several minutes.
  The appliance should not be used by physically, sensory or mentally handicapped persons (including children) or by persons without sufficient experience or knowledge, unless such persons are under supervision, or have been instructed on the use of the appliance, by the persons responsible for their safety.

• Hoarfrost or condensation may appear on the appliance’s walls when the ambient temperature and humidity is very high; wipe them with a dry cloth.

• In case of power cable damage it should be replaced, to avoid dangerous situations, by the Manufacturer, a service center or similar skilled personnel.

• Never turn the appliance on if it shows any signs of damage. If you are in doubt about the functionality of the appliance, contact a maintenance service.

TECHNICAL SPECIFICATION

• 12 … -24 °С
• 5 … 5 °С

Operating voltage| 160-260 W ~50 Hz
Rated voltage| 220-240 W ~50 Hz
Current, А| 0,6| 0,7
Noise level, dB| 41| 41
Power consumption, kW/24 h| 0,46| 0,52
Power consumption class| А+
Refrigerant| R600a (39 g)| R600a (45 g)
Net weight, kg| 21| 25
Size (w/d/h), mm| 545
476
835| 635
556
835

SCOPE OF SUPPLY

• Chest freezer – 1 pc.
• Food storage bin – 2 pcs.
• Ice scraper – 1 pc.
• Ice form – 1 pc.
• User Manual – 1 pc.

APPLIANCE DESCRIPTION

1. Lid handle
2. Food storage bin
3. Power cable
4. Grille
5. Control panel
6. Freezer housing
7. Drainage opening

APPLIANCE INSTALLATION

• The appliance should be transported in an upright position. Do not turn the appliance over. Tilting the appliance by more than 450 is not allowed.
  This appliance should not be built into furniture or operated in niches.

• Do not install the appliance in facilities with very high temperature and humidity.

• A minimum space of 10 cm shall be left between the rear and side walls of the freezer and adjacent walls to provide for proper air circulation.

• Install the appliance in a place protected from direct sunlight and heat sources. Direct sunlight can impact the acrylic coating and heat sources cause increase power consumption. Very low ambient temperatures can also cause improper operation of the appliance.

• After connecting the appliance to power supply, it should operate empty for 2 to 3 hours to cool down sufficiently before placing food in it.

ATTENTION! The device can be used in an unheated room at a temperature of -15 0C.

OPERATING PROCEDURE
SETTING THE TEMPERATURE

• The temperature in the freezer is adjusted using the control panel (5) located in its lower right corner.
• There is a green indicator light on the control panel.
• The temperature is set with the thermostat control knob.
• The Refrigerator setting means that the freezer will operate as a refrigerator.
  The Freezer setting means freezing. The appliance will freeze its contents.

ATTENTION!

• Pull the plug from the electric socket to disconnect the freezer from power supply.
• If the appliance has been turned off, You should wait for 3 to 5 minutes before turning it on again. Attempts to turn the appliance on before the abovementioned time elapses may result in damage to the electrical components and the compressor.
• If the freezer is overloaded with food the cooling may not be sufficient.

STORING FOODS

• Operate the freezer with the thermostat control knob set to the maximum position for 2 to 3 hours before placing food into the freezer to obtain the lowest possible temperature in the freezer chamber.

• After that time the thermostat control knob should be set to the medium position.

• It is not recommended to open the lid of the freezer too often or to leave it open for a prolonged time.

• The freezer chamber is designed for long-term storage of frozen foods. Foods can be stored for up to three months.

• Different foods have different storage lives which should not be exceeded. Follow the frozen food storage guidelines when defrosting the freezer chamber.
  Commercially packed frozen food should be stored in accordance with the manufacturer’s instructions provided on the packaging.

• Frozen foods should be placed in the freezer chamber immediately after buying. Follow the manufacturer’s storage instructions pro-vided on the packaging.

• The storage bin is designed for storing foods of irregular shape. In order to reach the other foods in the chamber the bin can be slid aside or lifted off.

• It is not allowed to place warm or hot foods, as well as liquids in glass containers and carbonated beverages and liquids in bottles and cans in the freezer.

DEFROSTING
For the most efficient operation and lower power consumption it is recommended to defrost the freezer every time the thickness of the ice coat reaches 5 to 10 mm. Choose the time for defrosting when the stock of food in the freezer is not large.

Do not use hot water to remove the ice as this can damage the plastic parts.
Do not use sharp objects to remove the ice as this can damage the appliance.
Do not use chlorine chemicals or acids during the cleaning process.

• Disconnect the freezer from power supply.
• Remove all foods from the freezer.
• Remove the drain plug located at the bottom of the freezer chamber. Place a suitable container for collecting the thawed water under the drain opening.
• Leave the freezer lid open.
• Remove the coat of ice when it starts to melt. This will reduce the defrosting time
• After defrosting wipe the internal surfaces of the freezer with a cloth damped in warm soapy water, then wipe with a dry cloth.

NOTE: Usually the defrosting takes several hours.
Pour slightly warm (not hot!) water on the ice so that it melts faster.

CLEANING

• It is recommended to clean the appliance immediately after installation.
• Disconnect the appliance from power supply, remove all foods and the storage bin.
• Wipe the internal surfaces with a cloth moistened with a warm baking soda solution. Use a ratio of 2 tablespoons of baking soda per 1 l of water.
• Wash the storage bin with a mild detergent.
• Keep the lid seals (rubber gaskets) clean for efficient operation.
• Clean the housing of the freezer with a mild detergent and warm water.
• Wipe the appliance dry with a soft cloth.
• Clean the condenser heat exchanger using a vacuum cleaner if it is contaminated with dust or dirt.
  It is recommended to clean the freezer during defrosting. This will allow to prevent the development of unpleasant odors and make operation of the appliance more efficient.

SUSPENDING APPLIANCE OPERATION

• Remove the frozen foods from the appliance.
• Disconnect the appliance from power supply.
• Perform appliance cleaning as described above.
• Leave the lid slightly open to prevent the possible development of condensate, mold or unpleasant odors.
• Do not leave children without supervision. The appliance should be kept out of reach of children.
• If you intend to suspend operation of the appliance for less than three months, you may leave it connected to power supply.

TRANSPORTATION

• The appliance should be transported in its packaging in a normal upright position by any type of enclosed vehicle. Securely fasten the appliance to prevent shocks and displacement inside the vehicle.
• It is not allowed to tilt the freezer by more than 45° during handling operations, as this can cause damage to the compressor and refrigerant system.

TROUBLESHOOTING

supply. The automatic circuit breaker or safety device has tripped. The thermostat is in the OFF position
The freezer turns on and  off too often| Room temperature is too high. The freezer is overloaded with  food. The lid is being opened too often. The lid is not fully closed. Wrong temperature setting. Lid seals are uptight. The freezer is installed too close to a wall. The freezer has been turned off for a prolonged time and requires 2-3 hours to fully cool down
The temperature  in  the freezer chamber is not low enough| Temperature setting  is  too high. Set a lower temperature. The temperature will stabilize within a few hours. The lid is being opened too often or for  tool  long. The lid is  not  fully closed. Lid seals are uptight.   A   large quantity of hot or warm food has been stored in the  freezer.  Wait   for the freezer to reach the set temperature. The freezer has been turned off for a prolonged time and requires  2-3 hours to fully cool down
The temperature  in  the freezer chamber is too low| Temperature setting is too low. Set a higher temperature. The temperature will stabilize within a few hours
Crackling sounds during  freezer operation| Metal parts are expanding or contracting like in heating piping. This is normal. The  sound appear  and disappear as long as the freezer continues operating
Bubbling sounds like boiling water during operation| Refrigerant  (used  for cooling the freezer chamber) is circulating in the system. This is normal
The freezer is vibrating| Check  if  the  freezer  is  installed level. Warped or saggy floor. The freezer is installed on a floor  that is unstable or moving. Ensure that the floor can support the weight of the freezer. Level out the freezer using wooden or metal shims under the corner supports. The freezer is touching  a wall. Reinstall  the freezer or move it away from the wall
The freezer lid will not   close properly| The freezer is not level. The lid gasket is contaminated. Storage bin installed improperly
Compressor surface becomes hot| This is normal. Do not  touch  the compressor

DISPOSAL
Upon expiry of its service life the appliance can be disposed of separately from ordinary domestic waste. You can turn it over to a special-ized electric and electronic appliance disposal and recycling centre.

CERTIFICATION DATA, GUARANTEE
The service life of this item is 10 years since the date of sale to the end user, provided the item will be used in strict accordance with the present manual and the applicable technical standards. Upon expiry of the service life please contact the nearest authorized service center for suggestions as to further operation of the appliance. The manufacturing date of the appliance is integrated into the serial number (digits 2 and 3 – year, digits 4 and 5 – month of manufacture). If any questions related to appliance maintenance should arise, or if the appliance has malfunctions, apply to the CENTEK TM Authorized Service Center. The address of the service center can be found on the website https://centek.ru/servis. Service support contacts: Phone: +7 (988) 24-00-178, VK: vk.com/centek_krd. General Service Center: OOO “Larina- Servis”, Krasnodar, Phone: +7 (861) 991-05-42.
The product has the Certificate of Conformity No ЕАЭС RU С-CN.НА46.В.03730/22 of 27.05.2022.

INFORMATION ABOUT THE MANUFACTURER, IMPORTER

Imported to EAEU by: OOO “Larina-Elektroniks”. Address: Russia, 350080 Krasnodar, ul. Demusa, 14. Phone: +7 (861) 2-600-900.

DEAR CONSUMER!
The guarantee period for all appliances amounts to 24 months from the date of sale to the end consumer. With this Warranty Card the Manufacturer confirms the proper condition of the appliance and undertakes to repair, free of charge, all defects caused by the Manufacturer’s default.

GUARANTEE MAINTENANCE TERMS

1. The guarantee shall be valid if the following documentation conditions are observed:
   The original Warranty Card shall be filled out correctly and clearly, indicating the of appliance model, serial number and sale date, the stamp of the seller company and signature of its representative shall be available, as well as the stamps on each coupon and the buyer’s signature in the Warranty Card.
   The Manufacturer reserves the right to reject guarantee maintenance if the buyer fails to provide the abovementioned documents or if the information contained therein is incomplete, illegible or ambiguous. 2. The guarantee shall be valid if the following operation conditions are observed:

   • The appliance is used in strict accordance with the present manual;
   • The safety rules and requirements are observed.

2. The guarantee does not apply to regular maintenance, cleaning, installation and setup of the appliance at the owner’s location.

3. The guarantee does not apply in the following cases:

   • mechanical damage;
   • normal wear of the appliance;
   • non-observance of operation requirements or erroneous actions on the part of the user;
   • improper installation or transportation;
   • natural disasters (lightning, fire, flood, etc.), as well as any other causes beyond the Manufacturer’s or Seller’s control;
   • ingress of foreign objects, liquids or insects into the inside of the appliance;
   • repairs or modifications to the appliance by unauthorized persons;
   • use of the appliance for commercial purposes (loads exceeding normal domestic application), connection of the appliance to utility and telecommunication networks incompliant with national technical standards;
   • failure of the following accessories, if replacement of these is al- lowed by design and does not involve disassembly of the appliance:
   • remote control units, rechargeable batteries, replaceable batteries (power cells), external power supply units and chargers;
   • consumables and accessories (packaging, covers, slings, carry bags, mesh screens, blades, flasks, plates, supports, grilles, spits, hos-es, tubes, brushes, nozzles, dust collectors, filters, smell absorbers);
   • for battery-powered appliances – operation with inappropriate or depleted batteries;
   • for rechargeable battery-powered appliances – any damage caused by improper battery charging and recharging.

4. The present guarantee is provided by the Manufacturer in addition to the consumer rights determined by the applicable legislation and does not limit these rights in any way.

5. The Manufacturer shall not be made liable for possible damage, directly or indirectly inflicted by CENTEK brand products on people, domestic animals, the consumer’s or third persons’ property if such damage is inflicted as the result of non-observance of appliance installation and operation requirements, deliberate or negligent ac-tions (omission) by the consumer or third persons, as well as of force majeure circumstances.
   Service centers will only accept appliances in a clean state (there should be no food residues, dust and other contamination on the appliance).

The Manufacturer reserves the right to change the design and specifications of the appliance without prior notice.

Email: WWW.CENTEK.RU

References

• Сервис - Официальный сайт Centek
• VK.com | VK
• Сервис - Официальный сайт Centek

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>