nVent RAYCHEM E-100-LBTV2 High-Profile End Seal Instruction Manual
- June 10, 2024
- nVent RAYCHEM
Table of Contents
RAYCHEM
E-100-LBTV2
High-Profile End Seal Installation Instructions
APPROVALS
Hazardous Locations
| Class I, Div. 2, Groups A, B, C, D Class II, Groups F, G
Class III CLI, ZN1, AEx e II T6 (1)
---|---
(1)
FM only
| CL I ZN 1 AEx eb IIC T6 Gb
Ex eb IIC T6 Gb
KIT CONTENTS
| Item | Qty | Description |
|---|---|---|
| A | 1 | End seal assembly |
| B | 1 | Cable tie |
| C | 1 | End seal label |
| D | 1 | Cable lubricant |
DESCRIPTION
The nVent RAYCHEM E-100-LBTV2 is a NEMA 4X-rated end seal kit for use with
nVent RAYCHEM LBTV2-CT heating cables. Once installed, the end seal is easily
re-entered for maintenance; the heating cable can be accessed without removing
the end seal. This kit may be installed at temperatures as low as –40°F
(–40°C).
For easier installation store above freezing until just before installation.
For technical support call nVent at
800-545-6258.
TOOLS REQUIRED
- Wire cutters
- Slotted screwdriver or nut driver
- Utility knife
- Adjustable pliers (two required)
MATERIALS REQUIRED
- Pipe strap
- GT–66 or GS–54 glass cloth tape
OPTIONAL MATERIALS
- For boot replacement order E–100–LBTV2–BOOT–5/PACK P/N 335089–000
WARNING: This component is an electrical device that must be installed correctly to ensure proper operation and to prevent shock or fire. Read these important warnings and carefully follow all of the installation instructions.
- To minimize the danger of fire from sustained electrical arcing if the heating cable is damaged or improperly installed, and to comply with the requirements of nVent, agency certifications, and national electrical codes, ground-fault equipment protection must be used. Arcing may not be stopped by conventional circuit breakers.
- Component approvals and performance are based on the use of nVent-specified parts only. Do not substitute parts or vinyl electrical tape.
- The black heating cable core is conductive and can short. It must be properly insulated and kept dry.
- Keep components and heating cable ends dry before and during installation.
- Bus wires will short if they contact each other. Keep bus wires separated.
- Use only fire-resistant insulation materials such as fiberglass wrap.
- Leave these installation instructions with the user for future reference.
CAUTION: Health Hazard: Prolonged or repeated contact with the sealant
in the end seal boot maycause skin irritation. Wash hands thoroughly.
Overheating or burning the sealant will produce fumes that may cause polymer
fume fever. Avoid contamination of cigarettes or tobacco. Consult MSDS VEN
0058 for further information. CHEMTREC 24-hour emergency telephone:
800-424-9300 Non-emergency health and
safety information:
800-545-6258.
E-100-LBTV2 RE-ENTRY’
©2021 nVent. All nVent marks and logos are owned or licensed by nVent Services
GmbH or its affiliates. All other trademarks are the property orespective
owners. nVent reserves the right to change specifications without notice.
RAYCHEM-IM-H56528-E100LBTV2-EN-2111
North America
Tel +1.800.545.6258
Fax +1.800.527.5703
thermal.info@nVent.com
Europe, Middle East, Africa
Tel +32.16.213.511
Fax +32.16.213.604
thermal.info@nVent.com
Asia Pacific
Tel +86.21.2412.1688
Fax +86.21.5426.3167
cn.thermal.info@nVent.com
Latin America
Tel +1.713.868.4800
Fax +1.713.868.2333
thermal.info@nVent.com
nVent.com/RAYCHEM
PN 689529–000
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>