Baolong Huf Electronics TMSS5C5 TPMS Sensor User Manual
- June 10, 2024
- Baolong Huf Electronics
Table of Contents
Baolong Huf Electronics TMSS5C5 TPMS Sensor
TPMS Sensor TMSS5C5
The TPMS Sensor TMSS5C5 is a Baolong Huf clamp-in sensor designed to
monitor tire pressure and temperature. It is easy to install and dismount, and
it comes with a warranty for one year.
Mounting and Dismounting Instructions
-
Mounting of Transmitter
-
Identify Transmitter – Make sure the prepared sensor is the same as the image provided in the instruction manual. Only plastic or aluminum caps, aluminum valves, and nickel-plated valve cores can be used when replaced.
-
Clean the rim – Before installing the transmitter, clean the rim around the hole with a cloth.
-
Insert the valve stem – Take off the nut, insert the valve stem through the rim hole from inside, and place the nut on the valve stem.
-
Tighten the nut – Tighten the nut with 5 Nm (44 inch pounds) torque.
-
Lock the rim – Lock the rim on the tire changer, ensuring that if the mounting head of the tire changer is positioned at 12 o’clock, then the valve should be at the 7 o’clock position. Apply lubricant on both the tire bead and rim. Mount the lower tire bead on the rim, ensuring that it does not touch the electronic module
during mounting. -
Mount the upper tire bead – Mount the upper tire bead following the same procedure as in step 5. If the mounting head of the tire changer is positioned at 12 o’clock, then the valve should be at the 5 o’clock position.
-
Inflate the tire – Inflate the tire to nominal pressure.
-
Check for leakage – Apply soapsuds on the valve tip. If no leakage is found, put on the valve cap. If unsuccessful, try again.
-
Balance the wheel – Dynamically balance the wheel before placing it back on the vehicle.
-
Dismounting of Transmitter
-
Deflate the tire – Deflate the tire and remove the wheel weights from the rim.
-
Push the tire bead away from the rim – Make sure to always set the bead breaker at least 90 degrees from the valve stem to avoid damaging the electronic module.
-
Firmly fix the wheel – Firmly fix the wheel on the turntable clamps, ensuring that if the mounting head of the tire changer is positioned at 12 o’clock, then the valve stem should be at the 11 o’clock position. Apply lubricant to both tire bead and rim, and then remove the upper tire bead.
-
Remove the lower tire bead – Use the same procedure as in step 3 to remove the lower tire bead. If the mounting head of the tire changer is at the 12 o’clock position, then the valve stem should also be at the 12 o’clock position.
-
Final inspection – Visually inspect the rim, valve stem, and electronic module to ensure no damage has occurred.
Authentication Announcements
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body. Additionally,
it is compliant with CAN ICES-3(B)/NMB-3(B) standards.
Warranty
This warranty covers substantial manufacturer’s defects in workmanship and materials. All components are covered for one year following the date of purchase. However, it does not cover any unit that is damaged beyond normal use, not properly installed, subject to chemical contact, or other acts not sanctioned by the Owner’s Manual. If the warranty period specified in local law exceeds the period provided by Baolong Huf, the former will supersede the latter.
Introduction of TMSS5C5
TMSS5C5 is the transmitting module in TPMS. Its working frequency is 2.4GHz;
Establish information communication via Bluetooth; 5dBm≥ EIRP. supply:
Battery. The
communication mode between WARDKS and receiving module is RF wireless
communication. The module detects pressure and temperature inner the tire
periodically and sends these information via RF output circuit to the
receiving module. One can manually detect data inner tire by LF wake-up tools.
Install it on the rim together with cycle valve.
PART ONE MOUNTING AND DISMOUNTING OF TRANSMITTER
Mounting of Transmitter
Identify Transmitter
Check whether the prepared sensor is the same with the image below.
Note: Only plastic or aluminum caps, aluminum valves and nickel plated valve
cores can be used when replaced.
- Before the transmitter is installed, the rim around the hole must be cleaned with a cloth.
- Take off the nut④, insert the valve stem through the rim hole from inside.
- Place nut④ on the valve stem, and tighten with 5 Nm (44 inch pounds) torque.
-
Lock the rim on the tyre changer. (If the mounting head of the tyre changer is positioned at 12 o’clock, then the valve should be at the 7 o’clock position.) Apply lubricant on both the tyre bead and rim. Mount the lower tyre bead on the rim. Ensure that the tyre bead does not touch the electronic module during mounting.
-
Mount the upper tyre bead the same way. (If the mounting head of the tyre changer is positioned at 12 o’clock, then the valve should be at the 5 o’clock position.) Inflate the tyre to nominal pressure.
-
Apply soapsuds on the valve tip. If no leakage is found, put on the valve cap6○. If unsuccessful, try again.
-
Dynamically balance the wheel before it is placed back on the vehicle.
Dismounting of Transmitter
- Deflate the tyre and remove the wheel weights from the rim. Push the tyre bead away from the rim. Make sure to always set the bead breaker at least 90 degrees from the valve stem to avoid damaging the electronic module.
- Firmly fix the wheel on the turntable clamps. (If the mounting head of the tyre changer is positioned at 12 o’clock, then the valves stem should be at the 11 o’clock position.) Apply lubricant to both tyre bead and rim, and then remove the upper tyre bead.
- Use the same procedure to dismount the lower tyre bead. (If the mounting head of the tyre changer is at the 12 o’clock position, then the valves stem should also be at the 12 o’clock position.)
- inal inspection: Visually inspect the rim, valve stem and electronic module to ensure no damage has occurred.
PART TWO FCC’s Authentication Announcements
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver s connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
PART THREE IC’s Authentication Announcements
CAN ICES-3(B)/NMB-3(B)
PART FOUR WARRANTY
This warranty covers substantial manufacturer’s defects in workmanship and
materials. It does not cover any unit that is damaged beyond normal use, not
properly installed, subject to chemical contact, or other acts not sanctioned
by the Owner’s Manual.
All components are covered for one year following the date of purchase. If the
warranty period specified in local law exceeds the period provided by Baolong
Huf, the former will supersede the latteThe warranty will be honored by any
authorized Baolong Huf dealer. The owner is required to provide date of proof
of purchase. The authorized dealer will determine if there is a warranty
condition associated with materials and/or manufacturing workmanship. If a
warranty condition exists, the component will be replaced free of charge and
shipping prepaid. The owner is responsible for any labor and installation
charges.
The warranty does not include any further obligation whatsoever, including but
not limited to actual installation of the replacement unit on the customer’s
vehicle.
All other Warranties, expressed or implied, are disclaimed. All collateral
agreements, which purport to modify this limited warranty, are of no effect.
The absolute limit of liability is the purchase price of the unit.
EU Conformity Statement
- This product and – if applicable – the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.
- 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see:www.recyclethis.info.
Please take attention that changes or modification not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may causeundesired operation of the device.
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Baolong Huf Shanghai Electronics Co.,Ltd. is not liable for any direct,
consequential, indirect or punitive damages of any kind.
Importer：
Huf Baolong Electronics Bretten GmbH
Gewerbestraße 40
D-75015 Bretten
NOTE: Baolong Huf Shanghai Electronics Co.,Ltd. reserves the right to change the contents of this manual at any time without notice. The information contained in this manual is proprietary and must not be reproduced without prior written consent from Baolong Huf Shanghai Electronics Co.,Ltd.
Company:Baolong Huf Shanghai Electronics Co.,Ltd.
Address: 1st Floor,Building 5,5500 Shenzhuan Rd,Songjiang,Shanghai
TEL:+86-21-31273333
Fax:+86-21-31190319
E-mail:sbic@baolong.biz
Web: www.baolong.biz
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>