Baolong Huf Shanghai Electronics TMSS6A3 TPMS Sensor User Manual

June 6, 2024
Baolong Huf Shanghai Electronics

Baolong LOGO Huf Shanghai Electronics TMSS6A3 TPMS Sensor
User Manual

OPERATION MANUAL OF TPMS SENSOR
MODEL:
TMSS6A3
Thank you for choosing our TPMS. This guide instructs the technician how to properly mount and dismount a Baolong Huf TPMS snap-in sensor.
Introduction of TMSS6A3
TMSS6A3 is the transmitting module in TPMS. Its working frequency is 315MHz; Receiver Low frequency 125KHz; supply:Battery;Radiofrequency uses the FSK modulation and Machester encoding mode;Antenna type:Monopole antenna,antenna Gain:-3.7dB~-3.4dB;cable loss3.12dB.The communication mode between WARDKS and receiving module is RF wireless communication. The module detects pressure and temperature inner the tire periodically and sends this information via an RF output circuit to the receiving module. One can manually detect data inner tire by LF wake-up tools. Install it on the rim together with the cycle valve.
PART ONE MOUNTING AND DISMOUNTING OF TRANSMITTER

Mounting of Transmitter

  1. Identify Transmitter
    Check whether the prepared sensor is the same as the image below.
    Note: Only plastic or aluminum caps, aluminum valves, and nickel-plated valve cores can be used when replaced.
    Baolong Huf Shanghai Electronics TMSS6A3 TPMS Sensor - Mounting of
Transmitter

  2. Before the transmitter is installed, the rim around the hole must be cleaned with a cloth.
    Baolong Huf Shanghai Electronics TMSS6A3 TPMS Sensor - Mounting of
Transmitter 2

  3. Remove the Self-lock Screw①, insert the valve stem through the rim hole from inside.
    Baolong Huf Shanghai Electronics TMSS6A3 TPMS Sensor - Mounting of
Transmitter 3

  4. Place the Self-lock Screw①on the valve stem, and tighten with 5 Nm (44 inch-pounds) torque.
    Baolong Huf Shanghai Electronics TMSS6A3 TPMS Sensor - Mounting of
Transmitter 4

  5. Lock the rim on the tire changer. (If the mounting head of the tire changer is positioned at 12 o’clock, then the valve should be at the 7 o’clock position.) Apply lubricant on both the tire bead and rim. Mount the lower tire bead on the rim. Ensure that the tire bead does not touch the electronic module during mounting.
    Baolong Huf Shanghai Electronics TMSS6A3 TPMS Sensor - Mounting of
Transmitter 5

  6. Mount the upper tire bead the same way. (If the mounting head of the tire changer is positioned at 12 o’clock, then the valve should be at the 5 o’clock position.) Inflate the tyre to nominal pressure.
    Baolong Huf Shanghai Electronics TMSS6A3 TPMS Sensor - Mounting of
Transmitter 6

  7. Apply soapsuds on the valve tip. If no leakage is found, put on the valve cap○6. If unsuccessful, try again.
    Baolong Huf Shanghai Electronics TMSS6A3 TPMS Sensor - Mounting of
Transmitter 7

  8. Dynamically balance the wheel before it is placed back on the vehicle.
    Baolong Huf Shanghai Electronics TMSS6A3 TPMS Sensor - Mounting of
Transmitter 8

Dismounting of Transmitter

  1. Deflate the tyre and remove the wheel weights from the rim. Push the tyre bead away from the rim. Make sure to always set the bead breaker at least 90 degrees from the valve stem to avoid damaging the electronic module.
    Baolong Huf Shanghai Electronics TMSS6A3 TPMS Sensor - Dismounting of
Transmitter 1

  2. Firmly fix the wheel on the turntable clamps. (If the mounting head of the tyre changer is positioned at 12 o’clock, then the valves stem should be at the 11 o’clock position.) Apply lubricant to both tyre bead and rim, and then remove the upper tyre bead.
    Baolong Huf Shanghai Electronics TMSS6A3 TPMS Sensor - Dismounting of
Transmitter 2

  3. Use the same procedure to dismount the lower tyre bead. (If the mounting head of the tyre changer is at the 12 o’clock position, then the valves stem should also be at the 12 o’clock position.)
    Baolong Huf Shanghai Electronics TMSS6A3 TPMS Sensor - Dismounting of
Transmitter 3

  4. Final inspection: Visually inspect the rim, valve stem, and electronic module to ensure no damage has occurred.

PART TWO FCC’s Authentication Announcements

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

PART THREE IC’s Authentication Announcements

CAN ICES-3(B)/NMB-3(B)

PART FOUR WARRANTY

This warranty covers substantial manufacturer defects in workmanship and materials. It does not cover any unit that is damaged beyond normal use, not properly installed, subject to chemical contact, or other acts not sanctioned by the Owner’s Manual.
All components are covered for one year following the date of purchase. If the warranty period specified in local law exceeds the period provided by Baolong Huf, the former will supersede the latter.
The warranty will be honored by any authorized Baolong Huf dealer. The owner is required to provide the date of proof of purchase. The authorized dealer will determine if there is a warranty condition associated with materials and/or manufacturing workmanship. If a warranty condition exists, the component will be replaced free of charge, and shipping prepaid. The owner is responsible for any labor and installation charges.
The warranty does not include any further obligation whatsoever, including but not limited to the actual installation of the replacement unit on the customer’s vehicle.
All other warranties, expressed or implied, are disclaimed. All collateral agreements, which purport to modify this limited warranty, are of no effect. The absolute limit of liability is the purchase price of the unit.

EU Conformity Statement
This product and – if applicable – the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the RED Directive 2014/53/EU, the RoHS Directive 2011/65/EU.
EU Conformity Statement
This product is marked with “CE” and comply therefore with the applicable harmonized European standards listed under the Radio Equipment Directive 2014/53/EU.

RF Exposure Information
This device has been tested and meets applicable limits for Radio Frequency (RF) exposure.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see:www.recyclethis.info.

Please take attention that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

  1. this device may not cause interference, and
  2. this device must accept any interference, including interference that may cause undesired operation of the device.

IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

  1. this device may not cause interference, and
  2. this device must accept any interference, including interference that may cause undesired operation of the device.

Baolong Huf Shanghai Electronics Co., Ltd. is not liable for any direct, consequential, indirect, or punitive damages of any kind.
Hereby, Baolong Huf Shanghai Electronics Co., Ltd. declares that the radio equipment type
TMSS6A3 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: https://www.intellisens.com/downloads
Frequency band: 315 MHz
Maximum Transmit Power: < 10 mW
Manufacturer:
Baolong Huf Shanghai Electronics Co., Ltd., 1st Floor, Building 5, 5500 Shenzhuan Rd, Songjiang Shanghai, China
Importer:
Huf Baolong Electronics Bretten GmbH
Gewerbestraße 40
D-75015 Bretten
NOTE: Baolong Huf Shanghai Electronics Co., Ltd. reserves the right to change the contents of this manual at any time without notice. The information contained in this manual is proprietary and must not be reproduced without prior written consent from Baolong Huf Shanghai Electronics Co., Ltd.
Company:Baolong Huf Shanghai Electronics Co.,Ltd.
Address:1st Floor,Building 5,5500 Shenzhuan Rd, Songjiang,Shanghai
TEL:+86-21-31273333
Fax:+86-21-31190319
E-mail:sbic@baolong.biz
Web:www.baolong.biz

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals