KOHLER 26305T-2MB Vibrant Brushed Moderne Brass Installation Guide
- June 10, 2024
- Kohler
Table of Contents
KOHLER 26305T-2MB Vibrant Brushed Moderne Brass
Product Information
The product model number is 1430516-T2. It is a showerhead produced by Kohler
Co. The showerhead has three different spray patterns – Boost, Sweep, and
Cloud Spray. It comes with adapters and screen washers and can be installed in
compliance with local plumbing and building codes. The product should be kept
away from a heater to prevent damage or personal injury.
Product Usage Instructions
-
Record the product model number: 1430516-T2.
-
Ensure compliance with local plumbing and building codes when installing the product.
-
Use an 8 mm drill bit to cut away the concrete and/or brick 1-3/4 (44 mm) to 3-3/4 (95 mm) above the finished ceiling.
-
Install G1/2 supply pipes.
-
Install the adapters and screen washers, and flush debris.
Reinstall the screen washers and adapters using an 8 mm hex wrench if necessary. -
Install the finished ceiling.
-
Ensure that the end of the adapters extends 1-1/4 (32 mm) to 2-11/16 (68 mm) from the finished ceiling.
-
Slide the dual arm onto the adapters and secure it with four setscrews.
-
Run water to flush debris from the nozzles.
-
If necessary, install the flow restrictor.
-
Rub debris from the nozzles periodically while water is running.
-
Rinse debris from the screen washer periodically.
WARNING: Risk of scalding. High water temperature can cause severe burns. Set the valve water temperature at or below 120°F (49°C). Refer to the temperature adjustment instructions for the valve.
CAUTION: Risk of product damage and personal injury. Keep the product away from a heater.
INSTALLATION
Follow all local plumbing and building codes
- 1A. 8 mm Drill Bit
- 1B. Sealant Tape
- 1C. 8 mm Hex Wrench
- 2A. Cut away the concrete and/or brick 1-3/4″ (44 mm) to 3-3/4″ (95 mm) above the finished ceiling.
- 3A. 8 mm Drill Bit
- 6A. Install G1/2 supply pipes.
- 7A. Using an 8 mm hex wrench, remove the adapters and screen washers. Flush debris. Reinstall the screen washers and adapters.
- 9A. Install the finished ceiling.
- 10A. The end of the adapters should extend 1-1/4″ (32 mm) to 2-11/16″ (68 mm) from the finished ceiling.
- 11A. Slide the dual arm onto the adapters. Secure with the four setscrews. 13A. Run water to flush debris.
- 14A. If needed, install the flow restrictor.
- 17A. If needed, install the flow restrictor.
- 18A. Boost
- 18B. Sweep
- 18C. Cloud Spray
- 19A. Periodically rub debris from the nozzles while water is running. 20A. Periodically rinse debris from the screen washer.
Need help? Contact our Customer Care Center.
- Thailand: callcenterthailand@kohler.com, +(66) 2700-9299
- Australia: 1800 KOHLER (1800-564-537)
- New Zealand: 0800-564-537
- Mainland China: +(86) 800-820-2628, +(86) 400-820-2628
- Hong Kong (China), Macau (China), Taiwan (China): +(852) 3125-7728
- Brunei, Guam, Indonesia, Japan, Malaysia, Mongolia, Philippines, Singapore, South Korea, Vietnam: +(86) 21-2606-2572
This product is covered under the Five-Year Limited Warranty for KOHLER® Faucets, found in the packed Compliance Certification.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>