TFA V60.2030.01 Easy-Charge Wireless Instruction Manual
- June 4, 2024
- TFA
Table of Contents
Instruction manual
Kat.Nr.:
60.2030.01
EASY-CHARGE WIRELESS
Digital alarm clock with an induction charger
Cat. No. 60.2030.01
Delivery contents:
- Digital alarm clock
- Power adaptor
- Instruction manual
Range of application and all the benefits of your new instrument at a glance:
- Inductive charging station (Qi certified) and USB charging function for mobile devices
- Colour display with an automatic colour change or direct colour selection with two brightness levels
- Indication of the clock, alarm time and alarm symbol
- Alarm with a rising alarm tone and 2 volume levels
- Snooze function
- Non-slip stand with 4 rubber pads
For your safety:
- This product is exclusively intended for the range of applications described above. This product should only be used as described within these instructions.
- Unauthorized repairs, alterations or changes to the product are prohibited.
Caution! Risk of electrocution!
- Plug the device only into a mains socket installed within your country’s electrical safety regulations and with a correct mains voltage (see nameplate).
- The main socket must be located near the equipment and it must be easily accessible.
- Unplug the device immediately if any fault occurs.
- The device and the power adapter must not come into contact with water or moisture.
- Only suitable for indoor use.
- Do not use the device if the housing or the power adapter are damaged.
- Operate the device out of reach of persons (including children) who cannot fully appreciate the potential risks of handling electrical equipment.
- Only use the supplied power adapter.
- Connect the lead to the device first and then plug the power adapter into the socket.
- Do not pull the plug out of the socket by its cable.
- Route the main cable so it does not come into contact with sharp-edged or hot objects.
WARNING
- Keep this device and the battery out of reach of children.
- Small parts can be swallowed by children (under three years old).
- Batteries contain harmful acids and may be hazardous if swallowed. If a battery is swallowed, this can lead to serious internal burns and death within two hours. If you suspect a battery could have been swallowed or otherwise caught in the body, seek medical help immediately.
- Batteries must not be thrown into a fire, short-circuited, taken apart or recharged. Risk of explosion!
- Low batteries should be changed as soon as possible to prevent damage caused by leaking. Make sure the polarities are correct. Avoid contact with skin, eyes and mucous membranes when handling leaking batteries.
In case of contact, immediately rinse the affected areas with water and consult a doctor.
CAUTION
- Unauthorized repairs, alterations, or changes to the product are prohibited.
- Do not expose the device to extreme temperatures, vibrations or shocks.
- Clean the instrument with a soft damp cloth. Do not use solvents or scouring agents.
- Protect the device from overheating and provide sufficient ventilation during operation. Make sure that the device is placed on a solid, clean surface. Do not place the device on cloth, carpet, paper, or other objects that could obstruct ventilation. Remove dust or other obstacles from the ventilation slots on the bottom of the device.
- Remove in case your metallic phone cover and do not place any metal objects on the charging pad.
- Do not place any other objects on the charging pad.
- Do not apply excessive force when connecting a USB cable. The USB plug fits only one way into the USB port.
- Remove the battery and pull out the plug of the socket if the device will not be used for an extended period of time.
Elements:
Display (Fig.1)
A – AM/PM in 12-hour format
B – Time
C – Snooze symbol
D – Daylight Saving Time (DST) symbol
E – ERROR symbol
F – Charging symbol
K – Alarm time
L – AM/PM in 12-hour format
M – Alarm symbol
Back (Fig.1)
G – DST ON/OFF button
H – Power adaptor jack
J – USB port
Left side (Fig.2)
A – TIME SET / LOCK / ALM SET switch
Right side (Fig.2)
B – ALARM / switch
Top (Fig.3)
A – Charging pad
C – button
D – SNOOZE/DIMMER button
E – button
Bottom (Fig.3)
B – Battery compartment
Getting started
-
Remove the protective film from the display.
-
Connect the attached power adapter to the alarm clock. Insert the power adapter pin into the device jack (Fig.1-H) and connect the plug to a wall socket.
Important! Make sure that your household voltage is no more than 240V!
Otherwise, your device may be damaged. -
The button cell battery will operate as a backup power source in the event of a power failure.
-
The device is ready for use.
Time setting
- Press and hold the SNOOZE/DIMMER button (Fig.3-D) in normal mode to choose between the 12 – or 24-hour system. In the 12-HR system
- AM (before noon) or PM (afternoon) appears on the display (Fig.1-A).
- Slide the switch (Fig.2-A) to the position TIME SET.
- Press the or button (Fig.3-C, E) to set the time.
- Press and hold the or button for fast mode.
- After setting slide the switch to the position LOCK.
- Press the DST ON/OFF button (Fig.1-G) to change the summer time in winter time and vice versa (+/- 1 hr).
In Daylight Saving Time DST (Fig.1-D) is shown on the display.
Note: If the alarm clock is first set up during summertime, please set the clock to wintertime and press the
DST ON/OFF button when setting is complete.
Alarm function
Alarm time setting
- Slide the switch (Fig.2-A) to the position ALM SET.
- Press the or button (Fig.3-C,E) to set the desired alarm time.
- Press and hold the or button for fast mode.
- After setting slide the switch to the position LOCK.
Activate alarm
- Slide the ALARM switch (Fig.2-B) to the position (loud) or (quiet).
- The alarm is activated. The alarm symbol (Fig.1-M) appears on the display.
Alarm clock function
-
When the set alarm time (Fig.1-K) is reached, the alarm clock will wake you up with the selected volume.
The alarm symbol (Fig.1-M) flashes. -
If the alarm is not stopped manually, the ascending alarm tone automatically turns off after three minutes and the alarm will be reactivated at the same set time on the following day.
The alarm symbol remains on the display. -
Press any button to turn off the alarm sound or press the SNOOZE/DIMMER button (Fig.3-D)to activate the snooze function.
-
The snooze symbol (Fig.1-C) will be flashing and the alarm will be interrupted for 5 minutes.
-
You can activate the snooze function up to 7 times.
-
Press any button to stop the snooze function.
Deactivate alarm
- Slide the ALARM switch (Fig.2-B) to the position.
- The alarm function is deactivated. The alarm symbol (Fig.1-M) disappears.
Display light
- Press the SNOOZE/DIMMER button (Fig.3-D) to adjust the brightness in 2 levels or to switch it off.
- Briefly press the or button (Fig.3-C,E) several times to choose the desired color.
- Press and hold the or button to choose a continuous color change.
- Press the or button to stop the continuous color change.
Charging function
Inductive charging of your mobile phone
- Put your mobile phone on the platform. Your phone should sit centred on the charging pad.
- The charging symbol appears and (Fig.1-F) and the symbol flashes when your phone is successful- fully charging.
- The charging symbol does not appear or ERROR (Fig.1-E) flashes on the display if your device is not positioned properly or if your device is not compatible with the Qi standard.
- You may need to remove your phone cover.
- Compatibility may vary based on phone model. Please check your phone’s manual for details.
Charging via USB
- This product also provides a USB charging port for devices that do not support wireless charging.
- Plug the USB cable (not included) into the USB port (Fig.1-J) port on the alarm clock and connect the other end to your mobile device. Make sure that the charging rate is suitable for your mobile device.
Troubleshooting
| Problem: | Solution: |
|---|---|
| No display | Connect the device to the power adapter Check the power adapter |
Press the SNOOZE/DIMMER button to activate the backlight
No charging function (wireless) Display ERROR| The mobile device is not Qi-
compatible Position the mobile device properly Remove metallic objects Remove
the cover Use a USB port
No charging function (USB)| Check the USB port connection
If your device fails to work despite these measures, contact the retailer where you purchased the product.
Specifications
Power consumption:| Power supply (included)
Input: 100-240V AC 50/60Hz 1,3A Max
Output: 9,0 V DC 3A, 27W
---|---
Average active efficiency:| ≥86,62%
No-load power consumption:| ≤0,10 W
Back-up battery:| CR2032 (included)
Charging output:| USB port (2A)
Wireless charger power output:| 10W
Housing dimension:| 114 x 110 x 34 mm
Weight:| 203 g (device only)
Waste disposal
This product and its packaging have been manufactured using high-grade
materials and components which can be recycled and reused. This reduces waste
and protects the environment. Dispose of the packaging in an environmentally
friendly manner using the collection systems that have been set up.
Disposal of the electrical device
Remove non-permanently installed batteries and rechargeable batteries from
the device and dispose of them separately. This product is labeled in
accordance with the EU Waste Electrical and Electronic Equipment Directive
(WEEE). Please do not dispose of this product in ordinary household waste. As
a consumer, you are required to take end-of-life devices to a designated
collection point for the disposal of electrical and electronic equipment, in
order to ensure environmentally-compatible disposal. Observe the current
regulations in place!
Disposal of the batteries
Never dispose of empty batteries and rechargeable batteries with ordinary
household waste. They contain pollutants which, if improperly disposed of, can
harm the environment and human health. As a consumer, you are required by law
to take them to your retail store or to an appropriate collection site
depending on national or local regulations in order to protect the
environment. The symbols for the contained heavy metals are: Cd = cadmium, Hg
= mercury, Pb = lead.
WARNING! Batteries containing lithium can explode
Batteries and rechargeable batteries containing lithium (Li=lithium) present a
high risk of fire and explosion due to heat or mechanical damage with
potentially serious consequences for people and the environment.
Pay particular attention to correct disposal.
No part of this manual may be reproduced without written consent of TFA
Dostmann. The technical data are correct at the time of going to print and may
change without prior notice.
The latest technical data and information about this product can be found in
our homepage by simply entering the product number in the search box.
www.tfa-dostmann.de
E-Mail: info@tfa-dostmann.de
TFA Dostmann GmbH & Co.KG
Zum Ottersberg 12
97877 Wertheim, Germany
Handelsregister-Nummer: Reg. Gericht Mannheim HRA 570186
10/21
Thank you for choosing this instrument from TFA.
Before you use this product: Please make sure you read the instruction manual
carefully.
The operating instructions are enclosed with the device or can be downloaded
at www.tfa-dostmann.de/en/service/downloads/instruction-manuals
This product should only be used as described within these instructions.
Following and respecting the instructions in your manual will prevent damage
to your instrument and loss of your statutory rights arising from defects due
to incorrect use. We shall not be liable for any damage occurring as a result
of the non-following of these instructions.
Please take particular note of the safety advice! Please keep this instruction
manual safe for future reference.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>