RYOBI R18S18G Battery Compressed Air Stapler Instruction Manual

: June 10, 2024
: RYOBI

Table of Contents

R18S18G Battery Compressed Air Stapler
INTENDED USE
STAPLER SAFETY WARNINGS
MAINTENANCE
ENVIRONMENTAL PROTECTION
SYMBOLS
SYMBOLS IN THIS MANUAL
TROUBLESHOOTING
GUARANTEE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

R18S18G
ORIGINAL INSTRUCTIONS

R18S18G Battery Compressed Air Stapler

Important!
It is essential that you read the instructions in this manual before assembling, maintaining and operating the product.

Subject to technical modification

Safety, performance, and dependability have been given top priority in the design of your stapler.

INTENDED USE

The stapler is intended to drive staples in soft materials such as wood. It can be used in the following:

Finish and trim (interior and exterior)
Door and window casing
Door jambs
Baseboard
Crown molding
Cabinetry
Cap and shoe molding
Molding
Wooden staircases
Door and window trim
Chair rail
Brick mold
Hardwood flooring
Paneling
Furniture

The stapler is not suitable for ﬁ xing electric cables.
Do not use the product in any way other than those stated for intended use.
NOTE: Some timbers (such as very dry hardwood) may require shorter staples to fully drive in.

WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

STAPLER SAFETY WARNINGS

Always assume that the tool contains fasteners.
Careless handling of the stapler can result in unexpected firing of fasteners and personal injury.
Do not point the tool towards yourself or anyone nearby. Unexpected triggering will discharge the fastener causing an injury.
Do not actuate the tool unless the tool is placed firmly against the workpiece. If the tool is not in contact with the workpiece, the fastener may be deflected away from your target.
Disconnect the tool from the power source when the fastener jams in the tool. While removing a jammed fastener, the stapler may be accidentally activated if it is plugged in.
Use caution while removing a jammed fastener. The mechanism may be under compression and the fastener may be forcefully discharged while attempting to free a jammed condition.
Do not use this stapler for fastening electrical cables. It is not designed for electric cable installation and may damage the insulation of electric cables thereby causing electric shock or fire hazards.

ADDITIONAL SAFETY WARNINGS

Always be aware that misuse and improper handling of the product can cause injury to yourself and others.
The product is designed for single-hand use. Do not hold the product by the front of the magazine. Do not put hands, head, or other parts of your body near the bottom of the magazine where the fastener exits the product, as serious personal injury could be caused.
Always ensure that the workpiece contact is fully positioned above the workpiece. Positioning the workpiece contact only partially above the workpiece could cause the fastener to miss the workpiece completely and result in serious personal injury.
Do not drive fasteners near edge of material. The workpiece may split causing the fastener to ricochet, injuring you or a coworker. Be aware that the fastener may follow the grain of the wood, causing it to protrude unexpectedly from the side of the work material or deflect, possibly causing injury.
Keep hands and body parts clear of immediate work area. Hold workpiece with clamps when necessary to keep hands and body out of potential harm. Be sure the workpiece is properly secured before pressing the fastener against the material. The workpiece contact may cause the work material to shift unexpectedly.
Keep face and body parts away from back of the tool cap when working in restricted areas. Sudden recoil can result in impact to the body, especially when stapling into hard or dense material.
During normal use the product will recoil immediately after driving a fastener. This is a normal function of the product. Do not attempt to prevent the recoil by holding the product against the work. Restriction to the recoil can result in a second fastener being driven from the product. Grip the handle firmly, let the product do the work and do not place second hand on top of the product or near exhaust at any time. Failure to heed this warning can result in serious personal injury.
Do not drive fasteners on top of other fasteners or with the product at an overly steep angle as this may cause deflection of fasteners which could cause injury.
Always check the work area for hidden wiring, gas lines, water lines, etc., before using the product on such work area.
After using the product in the contact actuation mode, switch it back to the full sequential mode.
The driving depth of the fastener may be adjusted beyond air pressure. It is advisable to test the depth on a scrap workpiece to determine the required depth for the application.
Only fasteners matching the description in the product specifications table can be used with the product. Using incorrect fasteners may lead to jamming or other malfunctions.

DEPTH ADJUSTMENT SAFETY WARNINGS

Always remove the battery before adjusting the depth of drive wheel.
Do not pull back on the adjustment wheel. The wheel is designed to be rotated.
Do not press the trigger while adjusting the depth of drive wheel.
Always select full sequential firing mode before adjusting the depth of drive.
Do not point the product towards yourself or anyone nearby when adjusting the depth of drive.

TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national provisions and regulations.
Follow all special requirements on packaging and labelling when transporting batteries by a third party. Ensure that no batteries can come in contact with other batteries or conductive materials while in transport by protecting exposed connectors with insulating, non-conductive caps or tape. Do not transport batteries that are cracked or leaking. Check with the forwarding company for further advice.

MAINTENANCE

WARNING
The product should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the product is not in use. Disconnecting the product will prevent accidental starting that could cause serious injury.

When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause product damage.
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.
Do not at any time let brake fluids, gasoline, petroleum based products, penetrating oils, etc., come in contact with plastic parts. They contain chemicals that can damage, weaken or destroy plastic.
Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask.
For greater safety and reliability, all repairs should be performed by an authorized service centre.

LUBRICATION
All of the bearings in the product are lubricated with a sufﬁ cient amount of high grade lubricant for the life span of the product under normal operating conditions. Therefore, no further lubrication is required.
Do not use lubricants on staplers, magazine or driving mechanism. Keep clean.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing of as waste. The machine, accessories and packaging should be sorted for environmental-friendly recycling.

SYMBOLS

| Safety alert| | Full sequential actuation
---|---|---|---
| CE conformity| | Contact actuation
| EurAsian Conformity Mark| Ga| Fastener gauge
| Ukrainian mark of conformity| | Diameter
| Please read the instructions carefully
before starting the machine.| | Fastener width
| Depth adjustment| |

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

SYMBOLS IN THIS MANUAL

| Note| | Shallow penetration
---|---|---|---
| Warning| | Connect battery
| Tip| | Torque, maximum
| LED light| | Torque, minimum
| Deep penetration| |

The following signal words and meanings are intended to explain the levels of risk associated with this product:

DANGER
Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.

WARNING
Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.

CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

CAUTION
(Without Safety Alert Symbol) Indicates a situation that may result in property damage.

Product specifications|
---|---
18V Stapler|
Model| R18S18G
Voltage| 18 V
Magazine capacity (number of staples)| 105
Fastener type: Narrow crown staple| 10 – 38 mm (3/8” – 1½”)
Staple size (length)| 5,5 – 6,1 mm (1/5” – 1/4”)
Staple width| 2,42 kg
Weight – excluding battery pack| 2,87 kg
Weight – according to EPTA Procedure 01/2003| Lp = 84,5 dB(A)3 dB
Measured sound values determined according to
EN 60745:| LW= 95,5 dB(A)3 dB
A-weighted sound pressure level
Uncertainty K|
A-weighted sound power level
Uncertainty K|
Wear ear protectors.| ah = 2,0 m/s21,5 m/s2
The vibration total values (triaxial vector sum) determined according to EN 60745:| RB18L13
RB18L15
RB18L20
RB18L25
RB18L40
RB18L50
Vibration emission value Uncertainty K| BCS618
BCL14181H
BCL14183H
RC18150

TROUBLESHOOTING

PROBLEM	POSSIBLE CAUSE	SOLUTION

Work-contacting element does not depress
fully – product does not operate.| Staples are low.
Work-contacting element is jammed.| Replenish staples.
Remove the battery and clear the debris.
Product operates properly, but fasteners are
not driven fully.| Air pressure is too low.
Depth of drive is not deep enough.
Staple is too long for wood hardness.| Increase the air pressure.
Adjust the depth of drive.
Use staple of the length that is appropriate for the wood.
Product operates properly, but fasteners are
driven too deep.| Air pressure is too high.
Depth of drive is too deep.| Decrease the air pressure.
Adjust the depth of drive.
Product jams frequently.| Staples are incorrect.
Staples are damaged.
Magazine is loose.
Magazine is dirty.| Verify that the size of staples is correct.
Replace the staples.
Tighten the screws.
Clean the magazine.
Product stops and LED work lights flash
rapidly.| Battery is low or has no charge.
Product is hot.| Recharge the battery.
Allow tool to cool.
Product has charged battery and LED work
lights flash slowly or LED work lights do not
turn off after approximately ten seconds of
non-use.| Product has malfunctioned.| Take product to the nearest authorised repair
centre.

WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardized test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may signiﬁcantly increase the exposure level over the total working period. An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may signiﬁcantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organization of work patterns.

GUARANTEE

In addition to any statutory rights resulting from the purchase, this product is covered by a guarantee as stated below.

The guarantee period is 24 months for consumers and commences on the date when the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no guarantee provided in case of professional or commercial use.
There is, in some cases (i.e. promotion, range of tools), a possibility to extend the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of the tool is clearly displayed in stores and/or on packaging. The end user needs to register his/her newly-acquired tools online within 8 days from the date of purchase. The end user may register for the extended warranty in his country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of the data which are required to enter online and they have to accept the terms and conditions. The registration conﬁrmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty. Your statutory rights remain unaffected.
The guarantee covers all defects of the product during the warranty period due to defaults in workmanship or material at the purchase date. The guarantee is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or being incorrectly connected. This guarantee does not apply to:
• any damage to the product that is the result of improper maintenance
• any product that has been altered or modified
• any product where original identification (trade mark, serial number) markings have been defaced, altered or removed
• any damage caused by non-observance of the instruction manual
• any non CE product
• any product which has been attempted to be repaired by an nonqualified professional or without prior authorization by Techtronic Industries
• any product connected to improper power supply (amps, voltage, frequency)
• any damage caused by external influences (chemical, physical, shocks) or foreign substances
• normal wear and tear of spare parts
• inappropriate use, overloading of the tool
• use of non-approved accessories or parts
• carburettor after 6 months, carburettor adjustments after 6 months
• power tool accessories provided with tool or purchased separately. Such exclusions include but is not limited to screw driver bits, drill bits, abrasive discs, sand paper and blades, lateral guide
• components (parts and accessories) subject to natural wear and tear, including but not limited to carbon brushes, chuck, power cord, auxiliary handle, sanding plate, dust bag, dust exhaust tube
For servicing, the product must be sent or presented to a RYOBI authorized service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
A repair/replacement under this guarantee is free of charge. It does not constitute an extension or a new start of the guarantee period. Exchanged parts or tools become our property. In some countries delivery charges or postage will have to be paid by the sender.
This guarantee is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and Russia. Outside these areas, please contact your authorized RYOBI dealer to determine if another warranty applies.

AUTHORISED SERVICE CENTRE
To ﬁnd an authorized service centre near you, visit http://uk.ryobitools.eu/header/service-and-support/service-agents.

EC declaration of conformity
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany

Herewith we declare that the product
18V Stapler
Brand: Ryobi
Model number: R18S18G
Serial number range: 44451101000001 – 44451101999999
is in conformity with the following European Directives and harmonised standards
2006/42/EC, 2004/108/EC(until 19 April 2016), 2014/30/EU (from 20 April 2016), 2011/65/EU,
EN 55014-1:2006+A1:2009+A2:2011, EN 55014-2:1997 + A1:2001 + A2:2008,
EN 60745-1:2009+A11:2010, EN 60745-2-16:2010
RoHS documentation is compiled according to EN 50581:2012

Andrew John Eyre (BEng, CEng, MIET)
Vice President, Regulatory & Safety
Winnenden, Sep. 01, 2015
Authorised to compile the technical file:
Alexander Krug, Managing Director
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany

Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
961152510-02https://tm.by