KleanseAIR KA-330HO Portable Air Filter System User Manual

KleanseAIR KA-330HO Portable Air Filter System

Product Information

KleanseAIR HO Air Purifier
The KleanseAIR HO Air Purifier is a portable commercial air filtration system designed to improve indoor air quality by removing particulates, microorganisms, and allergens through a 2-stage filtration process. The unit includes a pre-filter to maximize the life of the primary HEPA filter, which captures particles larger than 0.3 microns. The compact size of the unit makes it easily maneuverable and suitable for use in a variety of environments.

Product Features

• Portable commercial air filtration system
• 2-stage filtration process
• Pre-filter to maximize life of primary HEPA filter
• HEPA filter captures particles larger than 0.3 microns (including dust, mites, pollen, mold, spores, fungi, bacteria,  viruses, pet dander, and smoke)
• Compact size for easy maneuverability

Safety Notices/Use/Warranty

Users should read and save all notices, warnings, and safety instructions received with the equipment. The unit should not be operated without proper electrical grounding. If the unit is used in hazardous or potentially hazardous environments (such as mold mitigation job sites), users should wear NIOSH-approved protective gear when changing the HEPA filter and should dispose of used HEPA filters according to local regulations.

Product Usage Instructions

KleanseAIR HO Air Purifier

How It Works
The KleanseAIR HO Air Purifier utilizes a 2-stage filtration process to remove particulates, microorganisms, and allergens from indoor air. Stage 1 includes a pre-filter to clean the air of larger particles and maximize the life of the primary HEPA filter. Stage 2 uses a custom-made HEPA filter to capture harmful dust, allergens, pet dander, microorganisms, and other particulates larger than 0.3 microns.

Recommend Setup

Users should place the KleanseAIR HO Air Purifier in a central location for optimal air filtration. The unit should be plugged in to an electrical outlet and turned on using the control panel. Users can adjust the fan speed as desired to increase or decrease air flow through the unit.

PRODUCT Control Panel

The control panel includes a power button and fan speed settings. Users can press the power button to turn the unit on or off. The fan speed settings allow users to adjust the air flow through the unit and can be adjusted as desired.

Read and save all notices, warnings and safety instructions received with equipment.

Injury to Persons Hazard: If using the unit in a containment work area, turn off all sources of power to open combustion appliances such as fireplaces, boilers, furnaces, water heaters, and HVAC systems to avoid the risk of back drafting deadly carbon monoxide fumes from those appliances. Do not sit or ride on the unit. Do not set any liquids on the top of the unit or store items on top the unit.

Tipping Hazard:  If the unit is used in hazardous or potentially hazardous environments such as mold mitigation job sites:
Wear NIOSH-approved protective gear when changing the HEPA filter as it may contain mold spores and contaminates. Change the KleanseAIR Pre-Filter and HEPA filter after every remediation job. Dispose of used HEPA according to your local regulations.

Warning: Always disconnect power to the equipment and unplug before performing any service or maintenance.
Caution: Do not operate without proper electrical ground.
Danger: On equipment with blowers keep inlet and outlet vents, clean and clear of objects.

HOW IT WORKS

The KleanseAIR HO is your solution to improving your indoor air quality by removing particulates, microorganisms, and allergens, all at once through a 2-stage process. Stage l consists of a pre-filter that is used to maximize the life of the primary HEPA filter. Stage 2 uses a HEPA filter to capture harmful dust, allergens, pet dander, microorganisms, and other particulates larger than .3 microns.

The KleanseAIR utilizes multistage treatment and filtration enhanced to remove airborne particles such as dust and miscellaneous debris, and destroying microorganisms caught in the filter. The small size of the KleanseAIR allows it to be portable and easily maneuverable.

Stage 1: 14” x 14” x 1” MERV 8 Pre-Filter
This filter is used to clean the air of larger particles to keep the primary HEPA filter clean. These are standard filters that can be purchased on-line or a local hardware store.

Stage 2: HEPA Micro Pleated Media Filter
This deep HEPA filter removes particles at 0.3 microns and larger such as atmospheric dust, mites, pollen, mold, spores, fungi, bacteria, viruses, pet dander, smoke, and more. We recommend changing this filter 12-24 months or as needed. This filter is custom made by GallatinAIR, and you will need to contact us for replacements.

RECOMMEND SETUP

Set up the air system in an area where it will provide good air circulation but won’t get in the way. To help circulate air, you may want to set up one or more fans somewhat distant from the KleanseAIR unit(s). Have the fan(s) blow the air towards the air unit(s). This will help exchange the air so that it quickly gets processed through the system. Leaving a system running 24/7 will help clear the air faster. Do not place the air unit directly against a wall, as you want to ensure airflow. Please do not use it with an ozone-producing machine.

CONTROL PANEL

POWER ON AND SETTING FAN SPEED
Airflow from the KleanseAIR is controlled with a three-speed controller. This allows you to set the airflow at any speed you desire. The following provides you an estimated airflow at each position.

• Off Position
  In this position, the power to the fan is turned off.

• Low Position
  This is the medium fan speed and will provide approximately 150-200 cfm. This is its most quiet setting and will provide 3-4 air turns per hour*.

• Medium Position
  This is the medium fan speed and will provide approximately 200-250 cfm. This setting will provide 5-6 air turns per hour*.

• High Position
  This is the maximum fan speed and will provide approximately 300 cfm. This setting will provide 6 air turns per hour*.

Estimated upon 3600 cubic feet of airspace — a room that is 400 sqft with a ceiling height of eight feet.

TROUBLESHOOTING

Odor/pollutant is not eliminated| Remove source(s) from the area.

Remove contaminated item(s) from the area. Locate source and treat with Odor Eliminator.

Rep lace HEPA filter. Adjust the airspeed of the unit.

---|---
Odor returns after a few days| The site may have become re-contaminated, take steps to prevent recontamination and repeat the process above

Treat source odor with Odor Eliminator

Portable Air System will not turn on| Make sure the Mobile Air System is plugged in

Make sure the back panel is in place. Check power at the

outlet. Test the on/off switch.

The fan is not turning| Check for obstruction(s).

REPLACING FILTERS

• MAIN HEPA FILTER: These filters are designed explicitly for GallatinAIR KleanseAIR units to maximize the effectiveness of the air filtration process. We advise replacing the filter every 12-24 months depending on the air you are filtering. When you need a new filter(s), please contact us directly at 855-250-2400. When this manual was printed, the replacement filters are $109 each (with free shipping). If you want to order several filters, we would be happy to extend you a discount depending on the number you purchase.
• PRE-FILTER (14″ x 14″ x 1″): We recommend purchasing a MERV 8 filter from an on-line provider such as Amazon as they are relatively inexpensive. You can also buy these filters at most local hardware stores.
• AUTO REFILL PROGRAM: For those who are busy and don’t want to worry about ordering new filters  on time, GallatinAIR offers an automatic refill program. The yearly refill contains one (1) HEPA FILTER, (2) PRE-FILTERS, and (2) UVC LIGHTS. If you would like to sign up for yearly, please contact us at 855-250-2400.

Lifetime Limited WARRANTY

At GallatinAIR, we stand behind our products with a lifetime limited on the enclosure and a 1-Year warranty on major electrical components. Enclosure: Should you experience any defects in materials or workmanship with the enclosure over the unit’s lifetime, we will repair or replace the unit for free. Main Centrifugal Fan: If, within 12 months from the date of purchase, the primary fan fails, GallatinAIR will repair or replace the defective fan. All other electrical components: If within 12 months from date of purchase, any other electrical part fails (e.g., indicator lights, ballasts), GallatinAIR will repair or replace the unit for free.

The above is subject to the following conditions:

• Any claim made under this warranty must include a copy of a valid proof of purchase showing the date and place of purchase.
• Our obligation under this warranty is to the original purchaser only and may not be transferred.
• Product replacement does not include shipping costs or labor installation costs.
• GallatinAIR reserves the right to examine the product in question and its installation environment before replacement.
• If an identical replacement product is not available, GallatinAIR reserves the right to replace the defective product with a similar product.

This warranty relates to defects in manufacture, materials, or workmanship in a GallatinAIR KleanseAIR product supplied for use into commercial premises in the United States. It does not extend to:

• Damage resulting from failure to maintain the product in accordance with the Care and Maintenance instructions provided with the product.
• Normal wear and tear, scratches, or accidental damage
• Faults arising from improper use and/or installation.

All incidental or consequential damages are expressly excluded. No additional warranties, express or implied, are given, including but not limited to, any implied warranty of merchantability or fitness for a particular purpose.

When requesting warranty service, you will need to provide:

• an approved Return Merchandise Authorization number (RMA) issued by Customer Service
• a dated, valid proof of purchase (payment receipt from an authorized GallatinAIR reseller)
• a description of the problem

Shipping Your Unit to GallatinAIR: Items must be safely and adequately packed in such a manner to prevent damage to the part or product during shipment. For your safety, please ship via an insured carrier, which employs package tracking. GallatinAIR will provide a shipping label to the customer along with an RMA number.
Shipping Unit from GallatinAIR: After the warranty service is completed, any repaired or replacement parts/products will be return-shipped via Standard Ground Service paid for by the customer. Upgraded expedited shipment is available for a fee.

GallatinAIR will not service received items when:

1. The item is inspected and found to be not covered by the warranty.
2. The item is inspected and found to be damaged during shipment due to lack of proper packaging.

Return shipment of such products will be at the expense of the customer.
For products that are discontinued and no longer serviceable and/or replaceable, a pro-rated credit towards a purchase of another similar GallatinAIR brand product will be issued. For Warranty Services, please contact for instructions: GallatinAIR, LLC. 1-855-250-2400 www.gallatinair.com

CONTACTING US

To contact us with questions of any kind, please call us at 855.250.2400 or email us at info@gallatinair.com

References

• gallatinair.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>