OLIGHT WARRIOR 3 Upgraded Dual Switch Tactical Torch User Manual
- June 9, 2024
- OLIGHT
Table of Contents
OLIGHT WARRIOR 3 Upgraded Dual Switch Tactical Torch
Thank you for purchasing this Olight Product. Please read this manual carefully before use and keep it for future reference!
IN THE BOX
SPECIFICATIONS
All above specifications are test results based on ANSI/NEMA FL1-2009 Standard. The tests are performed using the battery included in the flashlight. Note: The maximum output brightness will decrease as the battery voltage decreases.
BATTERY INSTALLATION
Before first use, please unscrew the tailcap and remove the insulating film. If the battery needs to be replaced, make sure that the positive end of the new battery faces the flashlight head when you put it in.
AVAILABLE BATTERIES
- 1 x customized 5000mAh 21700 rechargeable lithium battery
INDICATORS ON BOTH SIDES
NOTE:
While the light is on, if the battery power is less than 10%, the lowest
indicator on the right side will glow red.
USB MAGNETIC CHARGING CABLE — MCC3
Parameter/Specification
-
Charging cable USB type A – magnetic charging connector, length: 0.5m
-
Input USB A – Type DC 5V 2A
-
Charging pattern CC&CV
-
Maximum charging current 2A
-
The voltage of a fully charged battery is 4.2V±0.05V
-
Time to fully charge
5.5 hours (For reference only. When the USB power source is insufficient to provide 5V 2A power capacity, the charging time will be longer) -
Charge indication
- Red: charging
- Green: full (over 95%) or disconnected with a flashlight
CHARGING
- Before the first use please fully charge the product.
- Connect the USB end of the magnetic charging cable to an external USB power source, then attach the other end of the cable to the charging port of the light (best charging efficiency with a 10W (5V 2A) USB power source). The red indicator means charging, while the green indicator means charging completed (battery level＞95%).
- Only charge with standard MCC3, not compatible with other MCC.
DANGER
- Do not shine the light directly into human eyes. This may cause temporary blindness or permanent damage to the eyes.
- Do not cover the flashlight’s head or place the head on the ground when the flashlight is on. The radiation energy may cause damage to the flashlight itself, or even result in the burning of flammable objects nearby.
- The battery can only be charged while installed in the flashlight.
WARNING
- Do not activate turbo mode repeatedly under high temperatures to prevent the flashlight body from overheating and hurting the user’s hand.
- The tail switch may not work while immersed in sea water or other conductive media. Please try to keep it clean and dry.
- Do not use non-protected rechargeable batteries.
- Please lock out the switches if the flashlight is left unused, carried, or transported. The heat built-up due to accidental activation may melt the lens of the flashlight, cause close objects to burn, or even result in unexpected disasters.
- Store the battery with care. If the battery needs to be changed, please take good care of the battery taken out. Do not mix it with conductive metals.
NOTICE
- When the flashlight is turned off, the current mode will be memorized. The modes that can be memorized are: moonlight, low, medium, and high mode ( after the light is turned off, high mode will be memorized for 1 minute before reverting to medium mode ). Turbo mode can not be memorized.
- Do not short-circuit the tail switch cap with the surrounding ring. A short circuit in this case will result in a weak electric discharge between them and may lead to a complete battery drain if it is in this state for too long.
EXCLUSION CLAUSE
Olight is not liable for damages or injuries sustained resulting from the
usage of the product inconsistent with the warnings in the manual, including
but not limited to using the product inconsistent with the recommended lockout
mode.
HOW TO OPERATE
SIDE SWITCH
- ON/OFF: Single click the side switch to turn the light ON/OFF. When the light is turned on again, it will return to the previously memorized mode.
- CHANGE BRIGHTNESS LEVEL: When the flashlight is on, press and hold the side switch and it will, starting from the present brightness level, automatically cycle through Low, Medium, and High mode. The mode is selected when the side switch has been released. ( Please note: moonlight and turbo are not in the automatic cycle ).
- MOONLIGHT MODE: When the flashlight is off, press and hold the side switch for over one second to access the moonlight mode. If the memorized mode is moonlight, simply click the switch to access it.
- TURBO AND RETURN: Fast double-click on side switch to enter into Turbo, and double-click again to return. If memory mode were High or Medium, the output is Medium; if memory mode were Low or Moonlight, the output is memory mode.
- STROBE: Quickly triple-click the side switch to enter the strobe mode. To quit this mode, single click or press and hold the side switch.
- LOCK/UNLOCK: When the flashlight is off, press and hold the side switch (for about 2 seconds) to access the button lockout mode (the flashlight will enter the moonlight mode first and then switch off to signal the lockout mode). In lockout mode, if you press and hold the side switch for less than one second or use the tail switch, the indicator to the right of the side switch will light up red at the lowest level for two seconds to signal that the light is still in lockout mode. To unlock it, keep holding the side switch for over one a second until the moonlight mode is on again.
TAIL SWITCH
The flashlight produces different output settings by pressing lightly or
hard on the tail switch (please refer to the following program
configurations).
TWO DIFFERENT PROGRAM CONFIGURATIONS CONFIGURATION 1 (FACTORY DEFAULT SETTING):
- Half-press for Medium, hard press for Turbo; Single press the tail switch (press and release quickly) to turn the flashlight on or off;
- Press and hold the tail switch for momentary on. Release to turn off.
- CONFIGURATION 2: Half-press for Turbo, hard press for Strobe, release switch to turn the flashlight off.
SWITCH BETWEEN DIFFERENT PROGRAM CONFIGURATIONS
Switch between configuration 1 and configuration 2 by pressing hard then
holding the tail switch and single press on the side switch at the same time;
when you release the tail switch, the Configuration will be selected.
WARRANTY
- Within 30 days of purchase: Contact the original seller for repair or replacement.
- Within 5 years of purchase: Contact Olight for repair or replacement.
- Battery warranty: Olight offers a one-year warranty for all rechargeable batteries.
- MCC USB magnetic charging cable: One year.
For any of the fragile or low-value fittings not covered above, like lanyards and clips, you can contact the post-sale within 30 days of the purchase, if it has any quality drawback or damage under normal use conditions. If such drawback or damage occurs after 30 days of the purchase or under abnormal use conditions, we will only offer conditional quality assurance as appropriate.
EU-DECLARATION OF CONFORMITY
EU-Declaration of Conformity can be found here:
https://olightworld.com/ec-declaration.
USA Customer Support
cs@olightstore.com
Global Customer Support
Customer-service@olightworld.com
Visit www.olightworld.com to see our complete product line of portable illumination tools.
Dongguan Olight E-Commerce Technology Co., Ltd
4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town,
Dongguan City, Guangdong, China.
Made in China.
References
- Olight | Illuminate Your World.
- Flashlights, Tactical Light, Outdoor Tools - Olight Official Store- Olight
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>