SEALEY SGL01 5W SMD LED Rechargeable Spray Gun Light Instructions

RECHARGEABLE SPRAY GUN LIGHT 5W SMDLED
MODEL NO: SGL01

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Refer to instructions

SAFETY

** Inspect the cable and connector for wear and damage to ensure items are safe before connecting to the power supply. If worn or damaged DO NOT use.
** Ensure the light is fully charged before initial use.
DO NOT charge in damp conditions.
DO NOT turn the light on when it is being charged.
DO NOT shine directly into your, another person’s, or an animal’s eyes.
DO NOT allow children to use the light.
DO NOT handle or move the light whilst it is being charged.
DO NOT use the light if you suspect that the battery or the light casing is damaged.
DO NOT leave the battery in a discharged state, recharge the battery immediately. Before storage, fully recharge the battery, and subsequently recharge the battery at least once every six months of non-use.
DO NOT attempt to open, disassemble, modify or service the battery pack.
DO NOT crush, puncture, short external contacts or dispose of in fire or water.
Replace only with the battery pack designated for this product.
Recycle or dispose of used batteries as stipulated by local regulation.
**** If the electrolyte in the cells gets on your skin, thoroughly rinse with water. If it gets in your eyes, rinse thoroughly with cool water and seek immediate medical attention.

INTRODUCTION

Rechargeable 100lm spray gun light with 25-45mm clamp. Suitable for home or Bodyshop use. Manufactured to fit most guns. Ideal for low light areas such as vehicle chassis and interior where traditional booth lights do not reach adequately. Supplied with Type-C USB charging cable.

SPECIFICATION

Model No:………………………………………………………….SGL01
Battery: ……………………………………………..3.7V 0.75Ah Li-Ion
Charging Time: ………………………………………………………2.5hr
Clamp Size: …………………………………………………… 25-45mm
CRI Rating: ……………………………………………………………… 90
IP Rating: ………………………………………………………………IP65
LED Type: ……………………………………………….. 5W SMD LED
Lumen Output: ………………………………….High/Low: 100/30lm
Operating Time: …………………………………… High/Low: 4/11hr

OPERATION

4.1. Fit the light to the spray gun by adjusting the length of the lower clamp section. Squeeze the release tabs and withdraw the clamp band to the required length.
4.2. Locate the locking screw into the receptacle on the clamp band and tighten it.
4.3. Adjust the orientation of the light to suit by rotating the housing using the knob on the side of the light.
4.4. Pressing the power button once will turn the light on to low power, pressing it again will increase the light, and pressing it a third time will turn the light off.

4.5. CHARGING
4.5.1. Connect the USB lead to the port on the end of the battery pack and the other end to a USB power socket. Turn on the power supply.
4.5.2. Switch off the power supply, remove the charging lead and replace the socket cover.

ENVIRONMENT PROTECTION
**** Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling center, and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.

BATTERY REMOVAL
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications, and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: The guarantee is 12 months from the purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

© Jack Sealey Limited
Original Language Version
SGL01 Issue 2 20/07/2022

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>