I-PRO WV-QEM506 Ceiling Mount Bracket Installation Guide

I-PRO WV-QEM506 Ceiling Mount Bracket Installation Guide

• Before attempting to connect or install this product, please read these instructions carefully and save this manual for future use.
• The external appearance and other parts shown in this manual may differ from the actual product within the scope that will not interfere with normal use due  toimprovement of the product

-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.

used in these documents should be used to search for information on our technical information website (https://i-pro.com/global/en/ surveillance/training support/support/technical information) and will guide you to the right information.

Caution:

• Before attempting to connect or operate this product, please read these instructions carefully.

Notice:

• This product is not suitable for use in locations where children are likely to be present.
• Do not install this product in locations where ordinary persons can easily reach.
• For information about screws and other parts required for installation, refer to the corresponding section of this document.

Precautions

• Do not use this bracket except with suitable cameras.
  Failure to observe this may cause a drop resulting in injury or accidents.

• Refer installation work to the dealer.
  Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury, or damage to the product. Be sure to consult the dealer.

• Take measures of protection against this product falling.
  Failure to observe this may cause a drop resulting in injury or accidents. Be sure to install the safety wire.

• The screws and bolts must be tightened to the specified torque.
  Failure to observe this may cause a drop resulting in injury or accidents.

• Install the product accurately and securely on a ceiling in accordance with the installation instructions.
  Failure to observe this may cause injury or accidents.

• Do not rub the edges of metal parts with your hand.
  Failure to observe this may cause injury

When using this product, also read the “Precautions” described in the operating instructions for the camera to be attached

Preface

This product is a ceiling embedded bracket that is designed to mount the network camera on a ceiling. This bracket can be used for an area with weak pull-out strength such as plasterboard in a double ceiling, and the embedded type makes the visible part of the camera smaller.

The latest information about the supported cameras .

Specifications

inches}*Including decorative cover thickness: 17.5 mm {11/16 inches}
Mass:| Approx. 2.0 kg {4.42 lbs}
Finish:| Main body:
Surface treatment steel sheet
Decorative cover:
ABS resin i-PRO white Black

Precautions for Installation

• In order to prevent injury, the product must be securely mounted to the ceilingaccording to the Installation Guide.

• This product is designed to be used indoors.
  This product is not operable outdoors. Do not expose this product to direct sunlight for hours and do not install the product near a heater or an air conditioner. Otherwise, it may cause deformation, discoloration and malfunction. Keep this product away from water and moisture.

• Installation area for this product
  Make sure that the installation area is strong enough to hold the total weight of the camera assembly before installation.
  The installation area shall have 165 mm {6-1/2 inches} or more space behind the ceiling.
  The thickness of the ceiling board for installation can range between 9 mm {11/32 inches} and 40 mm {1-9/16 inches}.

• Make sure to remove this product if it will no longer be used.
  
  Ceiling board: between 9 mm {11/32 inches} and 40 mm {1-9/16 inches}
  

Standard Accessories

Safety wire …………………………………… 1 pc.
Safety wire angle…………………………… 1 pc.

Fixing screw for attachment plate (M4 × 8 mm {5/16 inches}) ……..5 pcs. (of them, 1 for spare)

Template……………………………………….. 1 pc.
Decorative cover…………………………….. 1 pc

The product is shipped in a state where the safety wire is attached to the safety wire angle.

Other items that are needed (not included)

Anchor bolt (M10)*………………………… 2 pcs.
Nut (M10) …………………………………… 6 pcs.

One anchor is used for securing the mounting chassis, and the other anchor is used for connecting the safety wire. (See Step2)

IMPORTANT

• Prepare anchor bolts according to the material and strength of the area where the product is to be installed. The pull-out strength of the anchor bolt shall be more than 5 times of the total weight of the installed devices (including the camera body, ceiling mount bracket, anchor bolts, and all other parts).

Installation

Refer to the operating instructions of the camera for details on the camera installation (including the camera mounting, cable connection and adjustment).

Step 1
Create a ø300 mm {11-13/16 inches} hole.
Ceiling surface

Step 2
Install two anchor bolts (M10: locally procured) into the ceiling.

1. Determine the anchor bolt length (for securing the mounting chassis) by use of Template (accessory).
2. Position the nut (locally procured) by use of Template and mount the nut. (The distance between the bottom surfaces of the ceiling board and nut shall be 136 mm {5-11/32 inches}.)
   

IMPORTANT:

• When the existing anchor bolt is used as an anchor bolt for connecting the safety wire, make sure that the distance between the anchor bolt and camera mounting position is 1 m {3.28 feet} or less.

Step 3
Secure the safety wire angle (accessory) to the anchor bolt (for connecting the safety wire), and connect the safety wire (accessory).

1. Mount a nut so that the safety wire angle is secured on the anchor bolt.
2. Remove the safety wire from the safety wire angle.
3. Insert the groove of the portion ❶ of the safety wire angle into the anchor bolt.
4. Close the safety wire angle while inserting the groove of the portion ❷ of the safety wire angle into the anchor bolt.
5. Connect the safety wire to the safety wire angle again.
6. Engage the nut from beneath, and secure the safety wire angle with top and bottom nuts.
7. Engage another nut from beneath to tighten and secure the nut that was engaged from beneath in ⑥ in a double nut fashion.
   Image of safety wire connection
   

Note:

• When the existing anchor bolt that has been installed is used for connecting the safety wire, the use of 2 spacer nuts is helpful.
  

Step 4
Attach the safety wire.

Attach the safety wire to the mounting chassis as shown in the illustration below

Installation onward for the descriptions of the cable and the safety wire may be omitted.

Step 5
Check the orientation for inserting the mounting chassis into the ceiling.

To align the i-PRO logo on the decorative cover, align the direction of the mounting chassis before inserting the mounting chassis into the mounting hole on the ceiling board.

Step 6
Secure the mounting chassis

Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}

Step 7
Pull out the camera mounting stage

Step 8
Install the attachment plate

• Camera mounting method
  
  Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}

Step 9

For Step 9, follow the installation procedure in the camera installation section or the installation procedure leaflet.

  Recommended tightening torque: 1.2 N·m {0.89 lbf·ft}

Step 10
Mount the decorative cover.

Recommended tightening torque: 0.4 N·m {0.3 lbf·ft}

• **** Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}
• There are two places where the decorative cover fixing screw can be fixed: the position shown in the illustration and the opposite side

Support

https://www.i-pro.com/
© i-PRO Co., Ltd. 2023

References

• i-PRO
• i-pro.com/jp/ja/support_portal
• i-pro.com/jp/ja/support_portal/technical_information
• i-PRO

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>