GE APPLIANCES ADYR22 Portable Dehumidifier Owner’s Manual

ADYR22 Portable Dehumidifier
Owner’s Manual
ADYR22 ADYR35 ADYR50
APYR50 AWYR50

ADYR22 Portable Dehumidifier

Before you begin
Record the GE module number and password for wifi setup. To locate this information, see page 10.
GE Module Number #____
Password #____
Write the model and serial numbers here:
Model #
Serial #
You can find them on a label on the back of the dehumidifier.
GE is a trademark of the General Electric Company. Manufactured under trademark license.

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.
Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.
We take pride in the craftsmanship, innovation and design that goes into every GE Appliances product, and we think you will too. Among other things, registration of your  appliance ensures that we can deliver important product information and warranty details when you need them.
Register your GE appliance now online. Helpful websites and phone numbers are available in the Consumer Support section of this Owner’s Manual. You may also mail in  the pre-printed registration card included in the packing material.

SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
WARNING For your safety, the information in this manual must be followed to minimize the risk of fire, electric shock or personal injury.

• Use this appliance only for its intended purpose as described in this Owner’s Manual.
• This dehumidifier must be properly installed and grounded as described in this manual before it is used.
• Never operate this dehumidifier in an area that is likely to accumulate standing water. If this condition develops, for your safety disconnect the power supply before  stepping into the water.
• Never unplug your dehumidifier by pulling on the power cord. Always grip plug firmly and pull straight out from the receptacle.
• Immediately replace all electric service cords that have become frayed or otherwise damaged. A damaged power supply cord must be replaced with a new power supply  cord obtained from the manufacturer and not repaired. Do not use a cord that shows cracks or abrasion damage along its length or at either the plug or connector end.
• If the receptacle does not match the plug, the receptacle must be changed out by a qualified electrician
• If the SUPPLY CORD is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid a hazard.
• The appliance shall be installed in accordance with national wiring regulations.
• Turn the dehumidifier OFF and unplug it before cleaning.
• GE Appliances does not support any servicing of the dehumidifier. We strongly recommend that you do not attempt to service the dehumidifier yourself.
• For your safety, do not store or use combustible materials, gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance.
• All dehumidifiers contain refrigerants, which under federal law must be removed prior to product disposal. If you are getting rid of an old product with refrigerants,  check with the company handling disposal about what to do.
• Do not use outdoors.
• This dehumidifier is intended for indoor residential applications only. This dehumidifier should not be used for commercial or industrial applications.
• This appliance can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or  instruction concerning use of the appliance in a safe way and understand the hazards involved.

WARNING
USE OF EXTENSION CORDS RISK OF FIRE.
Could cause serious injury or death.
DO NOT use surge protectors or multi-outlet adaptors with this Dehumidifier.

HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.
DO NOT use an adapter plug with this appliance.
The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of  electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.
Where a 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
The dehumidifier should always be plugged into its own individual electrical outlet, which has a voltage rating matching the rating plate.
This provides the best performance and also prevents overloading house wiring circuits, which could cause a fire hazard from overheated wires.

WARNING
Risk of Fire or Explosion. This unit contains flammable refrigerant.
Additional safety precautions must be followed.

• Do not use means to accelerate the defrosting process or to clean, other than those recommended by the manufacturer.
• The appliance shall be stored in a room without continuously operating ignition sources (for example: open flames, an operating gas appliance or an operating electric  heater.
• Do not pierce or burn refrigerant tubing. Be aware that refrigerants may not contain an odor.
• Keep ventilation openings clear of obstruction.
• When handling, installing, and operating the appliance, care should be taken to avoid damage to the refrigerant tubing.
• Do not drill holes in the unit.
• Maintenance, cleaning, and service should only be performed by technicians properly trained and qualified in the use of flammable refrigerants.
• GE Appliances does not support any servicing of the sealed system components (i.e. refrigerant containing parts) in the product.
• Dispose of dehumidifier in accordance with Federal and Local Regulations. Flammable refrigerants require special disposal procedures. Contact your local authorities for  the environmentally safe disposal of your dehumidifier.

For appliance recycling information please visit GEAppliances.com/recycling.

OPERATING INSTRUCTIONS

Controls
Appearance may vary by model.

Controls
NOTE: When the bucket is full or removed, the controls cannot be set.

1. Power Pad
   Press to turn the dehumidifier on and off.
   NOTE: Turning off the power by pressing the Power button does NOT disconnect the appliance from power supply.

2. Fan Speed Pad
   Controls the fan speed.
   Press to select either High, Low, or Smart Dry fan speed.
   Set the fan control to High for maximum moisture removal.
   When the humidity has been reduced and quiet operation is preferred, set the fan control to Low. Smart Dry compares the set humidity level with the actual humidity  and adjusts the fan speed automatically.

3. Display
   Shows the set % humidity level while setting, then shows the actual (+/– 5% accuracy) room % humidity level.

4. Humidity Set Control Pads
   The humidity level can be set within a range of 35%
   RH (Relative Humidity) to 80% RH (Relative Humidity) in 5% increments or in Nonstop mode for continuous operation. To set the unit for continuous operation, press  the “–” pad until the “Nonstop” indicator light is illuminated.
   NOTE: If Nonstop is selected, the dehumidifier will operate continuously at its maximum dehumidification settings if attached to a hose to drain or until the bucket is  full. For drier air, press the “–” pad and set to a lower percent value (%). For damper air, press the “+” pad and set to a higher percent value (%). When you first use the  dehumidifier, set the humidity control to 45% or 50%. Allow at least 24 hours for the dehumidifier to achieve the humidity level. If you still have damper air than desired,  set the humidity level to a lower setting or select Nonstop for maximum dehumidification.

5. Filter Reset
   After 250 hours of operation, the Clean the Filter indicator light will glow to remind you to clean the filter. Remove the filter and clean it.
   Press and hold Filter button for 3 seconds to reset the filter reminder. See the Care and Cleaning section.

6. Timer Off
   While the dehumidifier is operating, press the Timer button. Press the “+” / “–” buttons to select the number of hours you want the dehumidifier to continue to operate before turning Off.
   NOTE: After displaying the time, the Display will revert to showing the current humidity after 5 seconds have passed.
   Pressing the Timer button will display the number of hours left on the Timer.
   Timer On
   While the dehumidifier is off, press the Timer button.
   Press the “+” / “–” buttons to select the number of hours you want the dehumidifier to remain off before turning On.
   NOTE: The display will show the number of hours left until the dehumidifier turns on.
   To cancel the Timer:
   Press the Timer button once, the hours remaining on the Timer will appear on the display. Press the Timer button against and the Timer will be cancelled.

7. Pump (on some models)
   Activates the internal pump. Press Timer for 3 seconds to activate the internal pump for automatic removal of condensate. The Pump On light will remain illuminated after 3 seconds. Press Timer again for 3 seconds to deactivate the pump. Before turning on the pump, ensure the included hose is connected.

8. Empty Indicator
   The “Empty” indicator will blink when the bucket is ready to be emptied, or when the bucket is removed and/or not replaced in the proper position.

9. WiFi (on some models)
   Hold the Filter Reset button for 3 seconds to enable connection of the dehumidifier to home WiFi .
   Download Samarths App for details at: GEAppliances.com/connect.

Other Features

Alarm
If the bucket is full or missing, an alarm will sound for about 10 seconds to remind you to empty and replace the bucket.
Auto Shut Off
The Water Level Control Switch shuts off the dehumidifier when the bucket is full, or when the bucket is removed and/or not replaced in the proper position.
NOTE: The fan and compressor will stop running as soon as the bucket is removed. The alarm will sound if the bucket is not replaced in the proper position after 3 minutes.
Auto Defrost
When frost builds up on the evaporator coils, the compressor will cycle off and the fan will continue to run until the frost disappears. When the coil is defrosted, the  compressor or fan will automatically restart and dehumidifying will resume.
Power Outage
In the case of a power outage or interruption, the unit will automatically restart, in the settings last used, after the power is restored.

Using the Dehumidifier

When first using the dehumidifier, operate the unit continuously for 24 hours.

How the Dehumidifier Operates
Moist, humid air is drawn over a cold refrigerated dehumidifying coil. Moisture in the air condenses on this coil and drains into a bucket (or through a hose and drain).
Dry, clean air is drawn through the condenser where it is heated and discharged out the top grille into the room.
It is normal for the surrounding air to become slightly warmer as the dehumidifier operates.

Choosing a Location
A dehumidifier operating in a basement will have little or noeffect in drying an adjacent enclosed storage area, such asa closet, unless there is adequate circulation of air in and
out of the area.

• Do not use outdoors.

• This dehumidifier is intended for indoor residential applications only. This dehumidifier should not be used for commercial or industrial applications.

• Place the dehumidifier on a smooth, level floor strong enough to support the unit with a full bucket of water.

• Allow at least 18 inches of air space on all sides of the unit for good air circulation.

• Place the dehumidifier in an area where the temperature will not fall below 41°F (5°C) or above 90°F (32°C). The coils can become covered with frost at temperatures below 41°F, which may reduce performance.

• The suggested range of relative humidity is between 40% and 50%

• Use the dehumidifier in cooking, laundry and dishwashing areas that have excessive moisture.
  NOTE: Place the dehumidifier away from the clothes dryer.

• Use the dehumidifier to prevent moisture damage anywhere books or valuables are stored.

• Use the dehumidifier in a basement to help prevent moisture damage.

• The dehumidifier must be operated in an enclosed area to be most effective.

• Close all doors, windows and other outside openings to the room.
  NOTE: The dehumidifier has casters to aid placement, but it should only be rolled on smooth, flat surfaces. Do not attempt to roll the dehumidifier on carpet or over objects.

Water Level
The dehumidifier will turn off automatically when the bucket is full, or when the bucket is removed or not replaced in the proper position.
The bucket must be replaced in the proper position for the dehumidifier to work. The empty indiator will blink and the dehumidifier will not run if the bucket is not in the proper position.

Bucket Operation
DO NOT remove the float or magnet in the bucket assembly. If removed the Dehumidifier will not work properly.

Always make sure the water bucket is locked into place on the dehumidifier.
Removing Collected Water
There are 3 ways to remove collected water:
– Use the bucket
– Use a garden hose
– Use the internal pump (on some models)
Use the bucket. When the bucket is removed, the unit will shut off. Empty and replace the bucket.
IMPORTANT: Do not use the hose if using the bucket to collect water. When the hose is connected, water will flow through it onto the floor instead of into the bucket.

Removing Collected Water (cont)
NOTES:

• Do not remove the bucket while the dehumidifier is operating or if it has just stopped operating. This might cause some water to drip from the drain pan.
• The bucket must be in place and securely seated for the dehumidifier to operate.

Use a garden hose. Water can be automatically emptied into a floor drain by attaching a garden water hose (not included).

1. Unscrew the cover to the hose outlet located at the rear of the dehumidifier just under the filter.
2. Thread a garden hose (not supplied) onto the nozzle and ensure it is seated securely. Cut to length and lead it to the floor drain.
3. Thread a garden hose (not supplied) onto the nozzle and ensure it is seated securely. Cut to length and lead it to the floor drain.
4. Replace the bucket in the unit.
   NOTE: The bucket must be in place and securely seated for the dehumidifier to operate. The garden hose must run down from the dehumidifier to the floor drain.

Use the internal pump (on some models)
Water can be automatically emptied into a remote location by attaching the included pump hose.

1. Remove the black rubber drain plug from the garden hose attachment exposing the hose bar.
2. Connect the included hose to the hose barb. Ensuring hose fully covers hose bar to prevent leaks.
3. Lead the hose discharge to desired drain location.
4. Make sure pump is activated. To activate the pump, press and hold the Timer button for 3 seconds. The Pump On indicator will remain illuminated.

IMPORTANT: Make sure the condensate hose is properly connected and is not kinked, bent or cracked as this may cause water to flow onto the floor. Please ensure the  bucket is empty before putting the unit into pump mode. The bucket must also be fully seated for the pump to work properly. Do not operate the machine if the room  temperature is 41°F or below.
NOTE: Maximum lift height is 16ft.

Care and Cleaning

Turn off the dehumidifier and remove the plug from the wall outlet before cleaning.
Grille and Case
To clean the case:
Use water and a mild detergent. Do not use bleach or abrasives.
To clean the rear grille:
Use a vacuum attachment or brush.

Water Bucket To clean:
Every few weeks, clean the bucket to prevent growth of mold, mildew and bacteria. Partially fill the bucket with clean water and add a little mild detergent. Swish it around in  the bucket, empty and rinse.
NOTE: Do not use a dishwasher to clean the water bucket.
To remove:
Remove the bucket and pour out any water.
To replace:
Slide the bucket into the dehumidifier.
NOTE: The bucket must be in place and securely seated for the dehumidifier to operate.

Air Filter
The air filter behind the rear grille should be checked and cleaned at least every 250 hours of operation or more often if necessary.
After 250 hours of operation, the Filter indicator light will glow to remind you to clean the filter. Remove the filter and clean it. Replace the filter and press and hold the filter  button for 3 seconds.
To remove:
Remove the rear grille and the filter will be attached.
To clean:
Clean the filter with warm, soapy water. Rinse and let the filter dry before replacing it.
NOTE: DO NOT put the filter in an automatic dishwasher.
CAUTION DO NOT operate the dehumidifier without a filter because dirt and lint will clog the unit and reduce performance.

Troubleshooting Tips

Before you call for service
Save time and money! Review the charts on the following pages first and you may not need to call for service.

&humidifiers plug is push. completely into the outlet.
The fuse is blown/circuit breaker is tripped.| Check the hou. fuse/circuit breaker box and replace the fuse or reset the breaker.
Dehumidifier has reached i. set humidity level or bucket is full.| The &humidifier automatically turns off when either condition occurs. Change to a lower setting or empty the bucket and replace properly.
Bucket is not in the proper position.| The bucket must be in place and securely seat. for the &humidifier to operate.
Power Failure.| There is a protective tirne delay (up to 3 minute.) to prevent tripping of the compressor overload. For this reason, the unit rmendoit Zorn, formal &humidification for 3 minut. after it
Dehumidifier does not dry the air as it should| Did not allow enough time to remove the moisture.| When first installed, allow at I.st 24 hours to maintain the &sir. dryness.
Airflow is restricted.| Make sure there are no curtains, blinds or furniture blocking the top or back of the &humidifier. See the Choosing a Location section.
Dirty Filter| See the Care and Cleaning section.
The Humidity Control may not be .t low enough.| For drier air, pre. the V pad and set to a lower percent value (%) or at the Nonstop setting for maximum dehumidification.
Doors and windows may not be dos. tightly.| Check that all doors, windows and other openings are securely dosed.
Clothes dryer may be blowing moisture-laden air into the room.| Install the dehumidifier away from the dyer. The dryer should be vented to the outski&.
Room temperature is too low.| Moisture removal is best at higher room temperatures. Lower
1:1:rdneltnirPeerdtgensZtiol rbeeu:pee threated Tttleirri;ererr:t unreels Trove 41°F (5°C).
Dehumidifier runs too much| Area to be dehumidify. is too large.| The capadty of your &humidifier may not be adequate
Doors and windows are open.| Close all doors and windows to the outside.
Frost appears on the coils| Room temperature is below 41°F (5°C)| Please operate unit at temperatures above 41 F (5 C). Frog will usually disappear within 60 minutes. Under certain conditions, frost may appear on the coils of your &humidifier at temperatures above 41°F (5°C). This is 41114 514 frost will usually disappear within 60 minutes. See the Automatic Defrost section.
Fan noise| Air is moving through the dehumidifier| This is normal.
Water on floor| Hose connection may be loose.| Check the hose connection. See the Removing Collected Water section.
Intended to use the bucket to collect water, but a hose was attach.| Disconnect the hose if using a bucket to collect water. See the Removing Collected Water section.
Bucket Full LED light flashing and alarm sounds while drain hose is connected| Drain hose not tight on fitting.| Check drain hose connection.
Drain hos. is kinked.| Ensure the drain hose is pointed straight &wn to the floor and is not kink. in anyway.
Bucket fills up when using Um, Pump (on some models)| Unit not in pump mode| Ensure pump is turned on and pump light is illuminat.
pump hose not ins…,| Ensure pump hose is properly installed on back of unit
Water level sensor issue| This may be caused by very humid conditions or error with &at sensor. Check unit for a P1 error code on display. If this is present – turn off the unit, unplug unit for a few seconds, plug back in and turn on the unit to r.et sensor. If this error continu. to occur refer to warranty section for exchange options.

WiFi Setup

GE Appliances SmartHQ (for customers in the United States)
GE Appliances Smart HQ Enabled*. If your Dehumidifier has a Connected Appliance Information label located on the outside as shown below, your dehumidifier is GE  Appliances Samarths Enabled. A WiFi communication card is built into the product allowing it to communicate with your smart phone for remote monitoring, control and notifications. Please visit www.GEAppliances.com/connect to learn more about connected appliance features, and to learn what connected appliance apps will work with your smart phone.

WiFi Connectivity:
For assistance with the appliance or the Connect Plus network connectivity (for models that are WiFi enabled or WiFi optional), please call 1-800-220-6899.

Getting Started

Appliances App. The app will walk you through the connection process. Download the app from iTunes or Google Play.

All connected appliace data is held in strict accordance with the GE Appliances Connected Data Privacy Policy.
Visit geappliances.com/privacy/privacy_policy connected to view this policy.

Questions about SmartHQ
Get answers you need about setting up WiFi appliances and connecting to your home network in our support articles.
Visit products.geappliances.com/appliance/geasupport-search- content to view wifi connect support articles.

REGULATORY INFORMATION

FCC/IC Compliance Statement:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and  used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a  particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.

Labelling: Changes or modifications to this unit not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
*Select Models Only
This product has Wi-Fi capability and requires Internet connectivity and a wireless router to enable interconnection with an Energy Management System, and/or with other  external devices, systems or applications.

GE Appliances Dehumidifier Limited Warranty

One Year
From the date of the original purchase| Replacement, repair, or refund of the original retail price for any product which fails due to a  defect in materials or workmanship. If the unit is exchanged, the replacement unit is warranted  for the remainder of your product’s original one-year warranty period. GE Appliances will, at  its sole discretion, replace the product with a product of the same or comparable functionality and quality or refund the original retail price.

In Order to Make a Warranty Claim During Your Retailer’s Allowable Return Period:

• Properly pack your unit. We recommend using the original carton and packing materials.
• Return the product to the retail location where it was purchased.
• Include in the package a copy of the sales receipt or other evidence of date of original purchase. Also print your name and address and a description of the defect.

In Order to Make a Warranty Claim During the Remainder of the One-Year Warranty:

• Locate your original sales receipt and make a note of your model and serial number.
• Call 866.907.1655 (in the United States) to initiate a warranty claim.
• You will be asked to provide your name, address, date of purchase, model and serial number.
• Warrant claims may require electronic or mailed-in evidence of purchase.

What Will Not Cover:

• Customer instruction. This owner’s manual provides information regarding operating instructions and user controls.
• Improper installation. If you have an installation problem, or if the product is of improper capacity, contact your dealer or installer. You are responsible for providing  adequate electrical connecting facilities.
• Failure of the product resulting from modifications to the product or due to unreasonable use including failure to provide reasonable and necessary maintenance.
• Replacement of house fuses or resetting of circuit breakers.
• Failure due to corrosion.
• Damage to the product caused by improper power supply voltage, accident, fire, floods or acts of God.
• Incidental or consequential damage caused by possible defects with this product.
• Damage caused after delivery.

EXCLUSION OF IMPLIED WARRANTIES –
Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties, including the  implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law.
For US Customers: This limited warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. If the  product is located in an area where service by a GE Appliances Authorized Servicer is not available, you may be responsible for a trip charge or you may be required to bring  the product to an Authorized GE Appliances Service location for service. In Alaska, the limited warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty gives you specific legal rights, and you may also have other  rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Staple your receipt here. Proof of the original purchase date is needed to obtain service under the warranty.

Warrantor US:
GE Appliances, a Haier company
Louisville, KY 40225

Consumer Support

GE Appliances Website
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day of the year! You can also shop for more great GE Appliances products and take advantage of all our on-line support services designed for your convenience. In the US: GEAppliances.com

Register Your Appliance
Register your new appliance on-line at your convenience! Timely product registration will allow for enhanced communication and prompt service under the terms of your  warranty, should the need arise. You may also mail in the pre-printed registration card included in the packing material. In the US: GEAppliances.com/register

Extended Warranties
Purchase a GE Appliances extended warranty and learn about special discounts that are available while your warranty is still in effect. You can purchase it on-line anytime.  GE Appliances Services will still be there after your warranty expires. In the US: GEAppliances.com/extended- warranty or call 800.626.2224 during normal business hours.

Remote Connectivity
For assistance with wireless network connectivity (for models with remote enable),visit our website at GEAppliances.com/connect or call 800.220.6899 in the US.

Parts and Accessories
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes (VISA, MasterCard and Discover cards are accepted). Order on- line today 24 hours every day.
In the US: GEApplianceparts.com or by phone at 877.959.8688 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause unsafe operation.

Contact Us
If you are not satisfied with the service you receive from GE Appliances, contact us on our Website with all the details including your phone number, or write to:
In the US: General Manager, Customer Relations | GE Appliances, Appliance Park | Louisville, KY 40225 GEAppliances.com/contact

References

• Appliance Parts, Accessories & Water Filters | GE Appliances
• Connect Your Smart Appliances
• Contact Us or Get Help with Questions | GE Appliances
• Bodewell Care Protection Plans
• Privacy Statement
• Recycling | GE Appliances
• GEAppliances.com/register
• Connect Your Smart Appliances

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>