AUBESS Smart LED Bulb User Manual

AUBESS Smart LED Bulb

Download the APP
Scan the QR code below to download “Magic Home pro” APP in APP Store or Google Play.

Install your smart light

Remove the bulb from its packaging and screw it into your light fixture. Then, turn it on.

Connect your light

1. Turn on Bluetooth.
2. Run the newest App “Magic Home Pro” and Register/ Login your Magic Home account.
3. Click “+” button on top right corner and choose the bulb which you want to connect. (If can’t found, reset your bulb)
4. Connect device to Wi-Fi network. (Choose your router and login your password, ensure the router is 2.4GHZ

Parameters

• 5 Channels: RGB+CCT
• Power: 7W/9W/10W
• Light Luminous Flux: 600LM/800LM
• Color Temperature:  2700k-6500K
• Working Temperature: -20-45°C
• Voltage: AC 100-240V, 50/60HZ / AC 100-130V, 50/60HZ / AC 190-240V, 50/60HZ
• Lamp Socket:  E26/E27 /B22

Restore the factory setting

1. Power on the bulb.
2. Wait 3-5 seconds and then power off the bulb.
3. At the end of the 4th time when you turn on the bulb, it will emit strobe for a few seconds, after that it will become fully bright at which point the reset is complete. Once you have reset the bulb, you should be able to see its wifi IP “LEDnet**” again under your mobile device’s wifi settings. (If not, please restart your wifi, wait for a while and you will see it).

Smart 2.4G remote controller

1. Pair the remote control:
   After the lamp is powered on, press the power button for 5 seconds immediately (within 3 seconds). When the lamp flashes slowly for 3 times, it means the pairing is successful.

2. Remove the remote control:
   After the bulb is powered on, press the power button for 5 seconds immediately (within 3 seconds). When the bulb flashes for 3 times, it means the removing is successful.

3. One-to-many control
   The remote control can be paired with multiple WiFi bulbs at the same time, and multiple WIFI bulbs can be controlled with one key without limitation.
   Note : Please refer to the steps of pairing or removing the remote.

4. Many-to-one control
   A single WIFI bulb can be paired with multiple remote controls, and each remote control can control the same WiFi bulb separately. ( a single bulb can support up to 16 remote controls)
   Note : Please refer to the steps of pairing or removing the remote control.

How do I connect to Google Assistant?

Step 1: Creating your Magic Home cloud account.
In order to control your smart light with the Google Assistant or control them remotely, you need to create a Magic Home cloud account and signed in.

Step 2: Add your light and modify the name.
Make sure there’s at least one smart light in device list, and enabled your lights for remote control. In the “Home” page, long press on the light you wish to rename.

Step 3: Add Home Control Action.
Add device in Home Control of the Home app. Select “Magic Home WiFi”.

Step 4: Login with your app account.
Enter your app account and password to finish the account linking. (Using your Magic Home cloud account you used in step 1 ). Your device should be listed in Home Control device list now.

Step 5: Control your light.
At this point, you’re all setup. You can now control your lights by issuing voice commands.

Supported Commands:

Say “Ok Google ” or “Hey Google”, then .. Turn on

• Dim
• Brighten
• Set to 150%]
• Dim/Brighteln byl50%]
• Turn [color]
• Turn on/off all the lights
• ls on ?

Changing colors on your lights

Color Options for Google Home control of your smart device:

• Blue
• Crimson
• Cyan
• Fuchsia
• Gold
• Green
• Lavender
• Lime
• Magenta
• Orange
• Purple
• Red
• Salmon
• Sky Blue
• Teal
• Turquoise
• Violet
• Yellow

For Scenes
You can activate scenes by following voice commands:

• Hey Google activate {scene name}
• Hey Google turn on {scene name}

How do I connect to Alexa?

Step 1: Creating your Magic Home cloud account.
In order to control your smart light wijh the Amazon Echo or control them remotely, you need to create a Magic Home cloud account and signed in.

Step 2: Add your light and modify the name.
Make sure there’s at least one smart light in device list, and enabled your lights for remote control. In the “Home” page, long press on the light you wish to rename.

Step 3: Enable Alexa Skill.
The next step is to download the Amazon Alexa app. Open the Amazon Alexa app and under the skills section, search for the “Magic Home” skill.

Step 4: Login and Discover Devices.

Enable the skill and sign in using your Magic Home cloud account you used in step 1. The next step is to discover your smart lights from the Alexa app. You can say “Alexa, discover devices” . Once Alexa has completed discovering your smart lights, they will appear in the Smart Home section of the Alexa app.

Step 5: Control your light.
At this point, you’re all setup. You can now control your lights by issuing voice commands.

Supported Commands:
These are some of the currently supported Alexa voice commands for the smart light.

• Alexa, set [light name] to [0-100]%
• Alexa, tum [light name] on/off
• Alexa, dim/brighten [light name]
• Alexa, increase/decrease [light name]
• Alexa, set the [light name] light to red
• Alexa, change the [light name] to the color blue
  For RGBW Light (Change to Warm White) Alexa, set the [light name] to warm white.

For CCT or RGBCW Light (Change to Color temperature)

• Alexa, make the [light name] warm white
• Alexa, change the [light name] to the cool white
• Alexa, set the [light name] to daylight

For Scenes
You can activate scenes by following voice commands:

• Alexa start {scene name}
• Alexa turn on {scene name}

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>