HAVIT Lighting HV1831W-12V Klip Inground Light Instruction Manual

Klip Inground Light Installation Instructions

Product Specifications

Model No.| HV1831W-12V| HV1831C-12V| HV1831W-240V| I HV1831C-240V
Name| Klip
Material| 316 Stainless Steel cover + Aluminium body
Colour| Cover – Stainless Steel I Body – Black
IP Rating| IP67
Input Voltage| 12v DC| 240V
Protection Class| (Low Voltage)| (Requires Earth)
Lamp Base| Built-In LED
Lamp Wattage| 1 x 7w| lx 7w
Colour Temp| 3000k| 5500k| 3000k| 5500k
Lumens| 5601m| 6301m| 5601m| 6301m
CRI| > 80
Wiring| Parallel
Dimmable| No
Warranty.| 3 Years Replacement*

Dimensions

Important Safety Issues:

• This product must be installed by a qualified electrician according to AS/NZS 3000.
• Ensure all electrical mains are disconnected before any installation.
• Modification of this product will void any warranty.
• Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
• When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required, if not within this allowance warranty \Ail be voided.
• Aluminum and 304SS fittings must not be installed within 5km of any saltwater environments.
• All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on the fitting. (Warranty does not cover Tea Staining)
• All o-rings and seals must be in place correctly to maintain a warranty
• When installing inground light fittings, Adequate drainage must be allowed to prevent fittings from sitting in water for a long period of time, if no drainage is allowed, the Warranty will be voided, See sample adequate drainage diagram for correct installation method.
• This form may be updated at any time due to product improvements, please check the online installation form for the most current version.

Adequate drainage

Steps for Installation:

HV1831-240V

1. Make sure that the electrical circuit is free of voltage (master switch off)
2. Make a hole where the fitting is to be placed using dimensions provided on line drawings, making sure adequate drainage is allowed.
3. Insert the canister, and ensure that the top is level with the ground or floor. Failure to do so will void the warranty.
4. To connect the cable, strip back cable on both fitting and cable run and twist the earths together first, then positive cables from fitting to positive on the cable run. Then connect neutral cables from fitting to neutral on cable run.
5. Solder all joins using solder and either a heat gun or butane gas torch.
6. Cover connections using an adhesive-lined heat shrink or gel cap to make the connection watertight. Failure to do this will void the warranty.
7. Heat the heat shrink or crimp the gel cap making sure all connections are covered.
8. Make sure the seals are still in place and screws are tight to avoid any water penetration.
9. Insert fitting into the canister. Apply silicon around the edge of the fitting to prevent any water from getting inside to electrical connections.
10. All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Steps for Installation: HV1831-12V

1. Make sure that the electrical circuit is free of voltage (master switch off)
2. Make a hole where the fitting is to be placed using dimensions provided on line drawings, making sure adequate drainage is allowed.
3. Insert the canister, and ensure that the top is level with the ground or floor. Failure to do so will void the warranty.
4. Using an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
5. Connect the cable – If more than one fitting is installed, wiring must be done in parallel.
6. Strip back the cable on both fitting and cable run and twist the positive cables together. Then connect neutral cables together
7. Solder all joins using solder and either a heat gun or butane gas torch.
8. Cover connections using an adhesive-lined heat shrink or gel cap to make the connection watertight. Failure to do this will void the warranty.
9. Heat the heat shrink or crimp the gel cap making sure all connections are covered.
10.  Make sure the seals are still in place and screws are tight to avoid any water penetration.
11.  Insert fitting into canister. Apply silicon around edge of fitting to prevent any water from getting inside to electrical connections.
12. All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Steps for Installation: HV1831-F-SH

1. Remove nuts on back of fitting and set aside
2. Remove cover and replace with security face
3. Reattach nuts and tighten making sure seals are still in place
4. Insert fitting into the canister
5. Insert screws and tighten

Steps for Installation: HV1831-HC

1. Remove nuts on back of fitting and set aside
2. Remove cover and glass and set aside
3. Insert Honeycomb lens on the inside of the glass
4. Reinsert glass onto fitting and place cover over glass
5. Reattach nuts and tighten making sure seals are still in place

Must be installed by a licensed electrician
Contact Details:
143 Beauchamp Road Tel: 02 9381 8300
Matraville NSW 2036 Fax: 02 9666 8881
Australia Email: sales@havit.com.au
Web:www.havit.com.au
*Warranty Terms & Conditions

https://havit.com.au/pages/warranty-terms-and-conditions
Additional Information**https://havit.com.au/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>