myWaves HB2 Sleep Headphones With Bluetooth User Manual

myWaves HB2 Sleep Headphones With Bluetooth

Features

Speakers are found inside the headband and can be adjusted over your ears by moving the materials around the speaker.

Description

1. Volume Down/Previous Song
2. Play/Pause
3. Volume Up
4. LED Status Light
5. USB Charging Port
6. Bluetooth Controller Box

Button Functions

• Power on: Hold Down the button for 3 Seconds
• Power off: Hold Down the button for 3 Seconds
• Increase Volume: short press + Button
• Decrease volume: short press – Button
• Previous Music: Hold press the – Button
• Next Music: Hold press the + button
• Play Music: Short press button
• Pause Music: Short press button

How to Charge:

1. Turn the headband inside out and find the charging port #5 in diagram at the opening.
2. Connect USB charging cable provided to the charging port and the other side of the cable to a power source ( Computer or Power Socket ).
3. LED light on the front of the headband will turn red while charging and change to blue when fully charged.

Battery Note:

• It will take approximately 2 hours to be fully charged.
• Charging cannot be done at the same time as listening to sounds.
• Reset for operation can be done while charging if required.
• Battery when fully charged will last approximately up to 9 hours.
• Red light will flash 5 times if the battery is low.

LED Indicator Chart:

Pair with Bluetooth Device:

1. Hold Down the button for 3 Seconds until Status light #4 starts flashing red and blue.
2. Turn the Bluetooth function on the device to be paired.
3. Select, on a paired device, the device name “Musical Eye Mask” from the list of found devices.
4. The passcode is 0000 if asked.
5. Blue light will flash slowly if successfully paired with the headband.

Play Music with Bluetooth Pairing:

1. Hold down the Play button quickly to start music or pause.
2. Adjust Volume by pressing + Up or – Down with a short press of a button.
   Note : After successfully pairing your mobile phone, you will need to open a music player on your phone to play music.

Troubleshooting

1. Ensure the product is fully charged, switched on , paired, or connected to the memory card.
2. If using Bluetooth, make sure your device is 10 meters/33 feed in range and no obstructions between devices.
3. Turn off all past Bluetooth devices that were previously connected to the device.

Washing Guidelines

Please use the inside pouch/opening on the back of the headband to access and remove the electronic parts before hand washing the product.

| Wash with cold water| | DO NOT dry clean
---|---|---|---
| Hand wash ONLY| | DO NOT bleach
| DO NOT tumble dry| | DO NOT iron

Specifications

• Bluetooth Version : V5.2
• Frequency : 2.402 GHZ – 2.480GhZ
• Transmission Range : 20M/66FT
• Rated Power : RMS 10mWx 2
• Speaker Unit : 32Ω x 20mm
• Battery : 3.7V 300mAh Rechargeable Li-Polymer Battery
• Charge Time : 2 Hours
• Battery Length : Approx 35 Hours

Dangers Of Injury

• Keep the product and the package away from children and animals, as they can swallow small parts.
• Supervise children using the product . It is not a toy.
• Always maintain a gap of at least 10 cm between the headphones and a pacemaker or an implantable cardioverter defibrillator (ICD) as the product generates magnetic fields.

Danger of Fire

• Caution! Don’t expose the headphones to any high temperatures over 70 degrees Celsius ( Like hair dryers, heating, prolonged sunlight etc..). The battery inside the headphones may overheat.
• Only charge the headphones in an ambient temperature area from 10 degrees Celsius to 40 degrees Celsius.
• Do not crush or pierce the battery! Do not expose the battery to high pressure, as this may cause an internal short-circuit and overheating.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Customer Support

Please contact info@mywaves.tech if you have further questions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>