LEVITON SQL3 Series Indoor Square Cylinders Instruction Manual
- June 9, 2024
- Leviton
Table of Contents
LEVITON SQL3 Series Indoor Square Cylinders
The important safeguards and instructions in this manual are not meant to cover all possible conditions and situations that may occur.
Note:
Before attempting installation, please refer to your local electrical code.
IMPORTANT SAFETY INSTRUCTIONS
- Read all the instructions before installation. SAVE THESE INSTRUCTIONS FOR LATER USE.
- Product should be installed by a Qualified Electrician.
- All electrical connections must be in accordance with local and National Electrical Code (NEC) standards. If you are unfamiliar with proper electrical wiring connections, obtain the services of a qualified electrician.
- Before starting the installation, make sure all electricity has been turned off and electrical breaker has been locked out and tagged out. Turning the power off at the light switch is not sufficient to prevent electrical shock.
- Product must be grounded to avoid potential electric shock and any other potential hazards.
- Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in compliance with National Electrical Code and local codes. Use of accessory equipment is not recommended.
- Do not mount near gas or electric heaters.
- Equipment should be mounted in locations and at heights where it will not readily be subject to tampering by unauthorized personnel.
- WARNING: RISK OF SHOCK
- Turn off the power at the fuse or circuit breaker box before installation or maintenance work.
- Wear rubber-soled shoes and work on a sturdy wooden or non-conductive ladder.
- Ground the fixture to avoid potential electric shocks and to ensure reliable starting.
- Double-check all connections, making sure they are tight and correct.
- WARNING: RISK OF FIRE
- Most dwellings built before 1985 have supply wire rated at 60°C
- Supply conductors (power wires) connecting the fixture must be rated at a minimum of 90°C
- Consult a qualified electrician before installation
- Installing contrary to instructions may cause unsafe conditions.
- If the product has any visible damage do not install it.
- To avoid hazards to children, account for all parts and properly dispose of all packing materials.
- Call the Technical Support department at ConTech Lighting with any installation questions: 847.559.5500.
INSTALLATION
FIGURE 1
Remove Conduit Feed Box from the Cylinder base and install it in the
desired location; hardware is not provided.
FIGURE 2
Loosen Conduit Strap Screws to remove Knockout Plug for desired entry points.
FIGURE 3
- Ensure 3/4 inch EMT Conduit is completely deburred and inserted into desired entry points. EMT Conduit should be fully seated against the built-in Stop Block.
- Tighten Outer Conduit Strap Screws, alternating to maintain even pressure.
- Tighten Center Set Screw to fully secure Conduit.
FIGURE 4
-
Clip Cylinder Tether to Conduit Feed Box Tether to assist in wiring.
-
Attach Black Line/Hot Wire to Black Wire, White/Neutral Wire to White Wire, and Green/Ground Wire to Green Wire with Wire Nuts FOR 0-10V DIMMING:
Attach the Purple Wire of the LED Driver to DIM (+) with a Wire Nut and the Pink/Gray Wire of the LED Driver to DIM (–) with Wire Nuts. If not dimming, use wire connectors to cap these wires individually. -
Carefully feed any excess wire into Conduit Feed Box to avoid pinching wires.
Electrical Connections:
- Green/Ground
- White/Neutral
- Black (Line)/Hot
0-10V Dimming Wires:
- Purple/Positive (+)
- Pink or Gray/Negative (–)
CONTECH LIGHTING | 725 LANDWEHR ROAD | NORTHBROOK, ILLINOIS 60062 | PHONE 847.559.5500 | www.contechlighting.com.
©2022 Conservation Technology of Illinois, LLC. All rights reserved.
Note:
Specifications subject to change without notice. All specifications subject to
change without notice. For ConTech’s limited product warranty, go to
www.contechlighting.com. For a printed copy
of the warranty, call 1-847-559-5500.