DRAPER 70432 Floor Fans User Manual
- June 9, 2024
- DRAPER
Table of Contents
FLOOR FANS
70432, 70433, 70438.
User Manual
Stock No. 70432 shown
These instructions accompanying the product are the original instructions.
This document is part of the product, keep it for the life of the product
passing it on to any subsequent holder of the product. Read all these
instructions before assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which
the product has been designed, and contains all the necessary information to
ensure its correct and safe use. By following all the general safety
instructions contained in this manual, it will ensure both product and
operator safety, together with longer life of the product itself.
All photographs and drawings in this manual are supplied by Draper Tools to
help illustrate the operation of the product.
Whilst every effort has been made to ensure the accuracy of information
contained in this manual, the Draper Tools policy of continuous improvement
determines the right to make modifications without prior warning.
INTRODUCTION
1.1 SCOPE
Suitable for circulating air on the floor level to create ventilation and help
cool spaces. Ideal for use in and around the home, gym, office or workshop.
Part of our core range, this product is suitable for enthusiasts and
tradespersons alike. Any application other than that it was intended for, is
considered misuse.
Local regulations may restrict the age of the operator.
1.2 UNDERSTANDING THIS MANUALS SAFETY CONTENT:
Warning! – Information that draws attention to the risk of injury or
death.
Caution! – Information that draws attention to the risk of damage to the
product or surroundings.
1.3 EXPLANATION OF SYMBOLS
| Before plugging in your tool, make sure the socket voltage matches that on
the product plate. If the socketvoltage does not match that shown on the type
plate, itcan result in a serious hazard and damage to your tool.
---|---
Important: Read instruction manuals before operating and servicing this
equipment.
For indoor use. Do not expose to rain.
Rated voltage
Motor capacity (Watts). (example of icon)
Machine weight. (example of icon)
WEEE – Waste Electrical & Electronic Equipment. Do not dispose of Waste
Electrical & Electronic Equipment in with domestic rubbish.
Class 1 appliance (Must be earthed).
Energy related Products.
UK Conformity Assessed.
SPECIFICATION
2.1 SPECIFICATION
Stock No. …………………………………………………….. 70432
Part No. ……………………………………………………. HV16FF
Rated voltage ………………………………………….. 230~50Hz
Rated input …………………………………………………….100W
Fan diameter Ø …………………………………. 15.3″ (388mm)
Guard diameter Ø…………………………………. 18″ (457mm)
Speed Settings ……………………………………………………… 3
Air flow (high) ……………………………………….. 90.24m³/min
Noise level (max) ……………………………………..65.29dB(A)
Weight (nett) …………………………………………………… 3.5kg
Stock No. …………………………………………………….. 70433
Part No. ……………………………………………………. HV18FF
Rated voltage ………………………………………….. 230~50Hz
Rated input …………………………………………………….120W
Fan diameter Ø …………………………………. 17.2″ (437mm)
Guard diameter Ø…………………………….. 20.25″ (514mm)
Speed Settings ……………………………………………………… 3
Air flow (high) ………………………………………106.93m³/min
Noise level (max) ……………………………………..65.65dB(A)
Weight (nett) …………………………………………………… 4.6kg
Stock No. …………………………………………………….. 70438
Part No. ……………………………………………………. HV20FF
Rated voltage ………………………………………….. 230~50Hz
Rated input …………………………………………………….120W
Fan diameter Ø …………………………………. 18.7″ (475mm)
Guard diameter Ø………………………………. 21.5″ (546mm)
Speed Settings ……………………………………………………… 3
Air flow (high) ………………………………………174.53m³/min
Noise level (max) ……………………………………..66.79dB(A)
Weight (nett) …………………………………………………… 5.2kg
HEALTH AND SAFETY INFORMATION
3.1 HEALTH AND SAFETY FOR FANS
Warning! – Please read the following instructions carefully, failure to
do so could lead to serious personal injury.
Draper Tools Ltd, recommends that this fan not be modified or used for any
application other than that forwhich is was designed. If you are unsure of its
relativeapplications, do not hesitate to contact us in writing andwe will
advise you.
- Keep out of the reach of children.
- Ensure fan is situated and used in an area free from loose furnishings, clothing, curtains etc that could get sucked in to the fan air inlet, or could block the fan blades.
- Do not leave the fan running unattended.
- Ensure the fan is situated and used in an area free from dust and ash that could be sucked up and cause air pollution. This will also damage the motor.
- Remove the plug from the socket before carrying outadjustment, servicing or maintenance.
- Complete any assembly procedures prior to connection to the power supply.
- Never insert fingers, pencils, or any other object through the protective grille, while the fan is running.
- Disconnect the fan from the power supply when moving it from one location to the other.
- Ensure the fan is switched off from the mains supply before removing the grille.
- Always complete the assembly of the fan before switching it on after cleaning.
- Always ensure the fan is secure on a firm and securesurface before operating.
- Do not use the fan near an open window, as rain cancreate an electrical hazard.
- If the power supply cable becomes damaged, it should be replaced immediately.
- If replacement of the supply cord is necessary, this should be carried out by the manufacturer or appropriate agent in order to avoid a safety hazard.
- Do not use this fan with an independant externally connected speed control device.
- Do not cover when in use.
- Do not use in the immediate surroundings of a bath, shower or swimming pool.
3.2 CONNECTION TO THE POWER SUPPLY
Caution: Risk of electric shock. Do not open.
This appliance is supplied with an approved plug and cable for your safety.
The value of the fuse fitted is marked on the pin face of the plug. Should the
fuse need replacing, ensure the substitute is of the correct rating, approved
to BS1362 and ASTA or BS Kite marked.
ASTA
BSI
Make sure the power supply information on the machine’s rating plate are
compatible with the power supply you intend to connect it to.
If a replacement plug is to be fitted this must be carried out by a qualified
electrician.
The damaged or incomplete plug, when cut from the cable shall be disabled to
prevent connection to a live electrical outlet.
This appliance is Class I † and is designed for connection to a power supply
matching that detailed on the rating label and compatible with the plug
fitted.
If an extension lead is required, use an approved and compatible lead rated
for this appliance. Follow all the instruction supplied with the extension
lead.
Earthed: This product requires an earth connection to protect against
electric shock from accessible conductive parts in the event of a failure of
the basic insulation.
Important: If using an extension lead, follow the instructions that came
with your lead regarding maximum load while cable is wound. If in doubt,
ensure that the entire cable is unwound. Using a coiled extension lead will
generate heat which could melt the lead and cause a fire.
UNPACKING AND CHECKING
4.1 PACKAGING
Carefully remove the product from the packaging and examine it for any sign of
damage. Check contents against the parts shown in Fig A. If any part is
damaged or missing, please contact the Draper Help Line (see back page). Do
not attempt to use the product!
The packaging material should be retained during the warranty period, in case
the product needs to be returned for repair.
Warning!
- Some of the packaging materials may be harmful to children. Do not leave any of these materials in reach of children.
- If any of the packaging is to be thrown away, make sure they are disposed of correctly, according to local regulations.
IDENTIFICATION
FIG.A
Stock No. 70432 shown
- Front Guard
- Blade
- Motor
- Rear Guard
- Stand
- Power supply
- Switch box
Note: For details of our full range of accessories and consumables, please visit drapertools.com
OPERATION
This fan is supplied fully assembled and ready for use.
Always ensure the fan is switched off, ensure mains plug is removed and that
the fan blade has stopped rotating before moving.
6.1 3 SPEED CONTROL – FIG. 1
Push button speed selection:
0= Off. Speeds 1= Slow, 2=Middle, 3= Fast.
Always ensure the fan is switched off, ensure mains plug is removed and that
the fan blade has stopped rotating before moving.
6.2 TILTING – FIG. 2
To adjust the angle and direction, tilt the fan by gently pushing or pulling
on the top of the fan housing.
DO NOT exert excess pressure or damage to the fan may occur.
MAINTENANCE
7.1 MAINTENANCE
- Always unplug the fan from the power supply before cleaning.
- All plastic components should be cleaned with a damp cloth. DO NOT spray with water/cleaning agents or immerse the fan unit in water.
- Warning! Ensure that any water and/or cleaning detergent DOES NOT enter the motor housing or switch mechanism.
- Ensure that the unit is clean, dry and correctly assembled after cleaning and before every use.
WARRANTY
8.1 WARRANTY
Draper tools have been carefully tested and inspected before shipment and are
guaranteed to be free from defective materials and workmanship.
Should the tool develop a fault, please return the complete tool to your
nearest distributor or contact:
Draper Tools Limited
UK: Chandler’s Ford, Eastleigh, Hampshire, SO53 1YF. England.
EU: Oude Graff 8, 6002 NL Weert (NL).
Telephone Sales Desk: +44 (0)23 8049 4333 or:
Product Helpline +44 (0)23 8049 4344.
A proof of purchase must be provided. If upon inspection it is found that the
fault occurring is due to defective materials or workmanship, repairs will be
carried out free of charge. This warranty period covering labour/parts is 12
months from the date of purchase except where tools are hired out when the
warranty period is 90 days from the date of purchase. This warranty does not
apply to any consumable parts, any type of battery or normal wear and tear,
nor does it cover any damage caused by misuse, careless or unsafe handling,
alterations, accidents, or repairs attempted or made by any personnel other
than the authorised Draper warranty repair agent.
Note: If the tool is found not to be within the terms of warranty,
repairs and carriage charges will be quoted and made accordingly.
This warranty applies in lieu of any other warranty expressed or implied and
variations of its terms are not authorised.
Your Draper warranty is not effective unless you can produce upon request a
dated receipt or invoice to verify your proof of purchase within the warranty
period.
Please note that this warranty is an additional benefit and does not affect
your statutory rights.
Draper Tools Limited.
DISPOSAL
9.1 DISPOSAL
- At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations.
- Contact your local authority for details of collection schemes in your area.
In all circumstances:
- Do not dispose of power tools with domestic waste.
- Do not incinerate.
- Do not dispose of WEEE* as unsorted municipal waste.
** Waste Electrical & Electronic Equipment.
NOTES
** ……………………………………………………………………………….
……………………………………………………………………………..
………………………………………………………………………………
……………………………………………………………………………..
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>