LEXICON LE45 Mobile Computer User Guide
- June 5, 2024
- lexicon
Table of Contents
LEXICON LE45 Mobile Computer
Features
Features front and side views
- Power Button
- LCD display
- Right Scan Trigger Button
- Left Scan Trigger Button
- USB-C connector
- Keypad
- Battery
- Notification LEDs
Features rear, top and bottom views
- Data Capture Window
- Bottom Pogo Pin
- Speaker
- Handstrap clip
- Battery pack
- Handstrap Bar
cradling and charging
Cradling the device
- Sliding the device into the device with slight angle
- Slightly push the device back
- The device is sitting on the cradle in a secure manner
Charging the device
- Connect the power supply to the cradle, make sure the cradle orange LED is blinking
- Put the device on the cradle
- Charging status LED on device
- Red LED = charging
- Green LED = 90% or above charged
Important notes
8 hours is recommended for the 1st time charging. Recharge of 5000mAh will
take 3-4 hours for 80% battery capacity.
Installing hand strap
- holder. Remove screws from hand strap
- Separate the velcro of the hand strap.
- Feed the loose end of the extended handstrap through the handstrap clip
- Wrap the hand strap around the clip and fasten together to close the strap
- Install the screws back to handstrap holder.
Enabling & disabling WiFi
Enabling WiFi
- Tap Apps icon, then select Settings
- Go to Network connections, turn on WiFi
- Tap the WiFi text on the setting screen
- A list of WiFi networks appears, pick the desired AP and setup as the wireless AP properties as usual
Disabling WiFi
- Tap Apps icon, then select Settings
- Go to Network connections, turn off WiFi
Enabling & disabling BT
Enabling Bluetooth
- Tap Apps icon, then select Setting
- Go to Network connections, turn on Bluetooth
- Tap the Blyetooth text on the setting screen
- A list of bluetooth devices appears, pick the desired device to pair up
Disabling Bluetooth
- Tap Apps icon, then select Settings
- Go to Network connections, turn off Bluetooth
Reboot and factory data reset
Performing reboot
- Long press power button
- . A menu appears , keep to hold the power key until the device reboot
Performing factory data reset
- Tap Apps icon, then select Settings
- In Personal section, select Back up and reset
- Select Factory data reset, click Reset phone
Refreshing RT55 ROM
- Copy RT55 ROM zip file to the root directory of the microSD card
- Open the battery cover, remove the battery
- Insert the microSD card
- Install the battery to the battery compartment
- Press and hold the power button and the F2 button for few seconds
- Continue to press and hold the F2 button and power button until the update screen appears
- Press F2 and select [Recovery Mode], then press 8 10 F1 to select. Update menu will then appear.
- Use F2 button to select update from SD card, press the F4 button to confirm
- Select the update file from SD card, press F4 button to confirm
- After complete installation, select wipe factory reset, ww.lexicontech.com press F4 button to confirm
- Select Yes – delete all us, press enter
- Finally select “reboot system now” to reboot 11 the device
Enabling scanner
- Remove the scanner film on the scanner window
- Tap Apps icon, then select ScanDemo
- Press the scanner button on the device to scan the barcode
- Barcode data will be shown on the screen
Battery warning
Battery safety guidelines
- Use manufacturer’s original battery and charger only. Any incompatible battery or charger may result in a fire, explosion, or other hazard.
- Do not disassemble or open, crush, bend or deform, puncture, or shred the battery.
- Do not short-circuit a battery by allowing conductive materials to contact the battery terminals.
- Do not immerse or expose the battery to water or other liquids.
- Do not dispose of batteries in fire or place the battery into a microwave oven or dryer.
- If battery leakage is found, avoid the liquid to come in contact with the skin or eyes.
- If contact has been made, rinse the affected area with water and seek medical advice.
- If you suspect damage to your equipment or battery, contact the manufacturer for inspection.
- Follow the local regulations to dispose or recycle the used re-chargeable batteries.
Regulation and maintenance
FCC and Canadian Compliance
Tested to Comply with FCC Standards.
LE45 mobile computers meet or exceed all applicable standards and have been
manufactured to the highest level of quality.
Waste Electrical and Electronic Equipment (WEEE) Information
This product has the extraction and use of natural resources for its
production. It may contain hazardous substances that could impact health and
the environment, if not properly disposed. In order to avoid the dissemination
of those substances in our environment and to diminish the pressure on the
natural resources, we encourage you to use the appropriate take-back systems
for product disposal. Those systems will reuse or recycle most of the
materials of the product you are disposing in a sound way. The crossed out
wheeled bin symbol informs you that the product should not be disposed of
along with municipal waste and invites you to use the appropriate separate
take-back systems for product disposal. If you need more information on the
collection, reuse and recycling of these systems, please contact your local
region’s waste administration. You may also contact your supplier for more
information on the environmental performances of this product.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This Product meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure
Information and Statement the SAR limit of USA (FCC) is HEAD AND TRUNK LIMIT
FOR 1-g(1.6 W/kg) AND EXTREMITY FOR 10-g(4.0 W/kg) averaged over one gram of
this Device LE45 (FCC ID: 2AWU8-LE45) has been tested against this SAR limit.
SAR information on this can be viewed on-line at
http://www.fcc.gov/oet/ea/fccid/. Please use the device FCC ID number for
search. This device was tested for typical operations 10mm from the body and
0mm from the hands. To maintain compliance with FCC RF exposure requirements,
10mm separation distance should be maintained to the user’s bodies and mm
separation distance should maintain to the hands
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
References
- Printer Repairs | Refurbished Equipment | Equipment Repair Service
- Printer Repairs | Refurbished Equipment | Equipment Repair Service
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>