ENFORCER 4K HDMI 4×2 Matrix HDMI Video Switcher Splitter Instruction Manual

4K HDMI 4×2 Matrix MVM-AH42-42Q
Installation Manual

4K HDMI 4×2 Matrix HDMI Video Switcher Splitter

The ENFORCER 4K HDMI 4×2 Matrix can switch 4 HDMI sources to 2 HDMI displays. It supports up to 4K2K@60Hz YCbCr 4:4:4 and HDCP 2.2 and can extract  HDMI source audio to optical and analog L/R output. It can downscale to 1080p for displays that cannot display 4K. It supports ARC and EDID over 18Gbps bandwidth  and can be controlled by buttons on the front or with an included remote control.

• 4 HDMI inputs and 2 HDMI outputs – each output can display any of the four sources
• Supports 4K2K@50/60Hz (YCbCr 4:4:4), 4K2K@30Hz, all HDMI 3D formats and more
• Supports 18Gbps video bandwidth uncompressed
• Both outputs can downscale to 1080p if needed
• Supports HDR10+, Dolby Vision, and HLG
• Supports advanced EDID management, including AUTO, COPY, and STD
• Supports Audio Return Channel (ARC)
• Easy control via buttons on front or an included remote control

Parts List

1x Matrix 1x Remote control 1x 12VDC Power adapter 2x Mounting ears 1x Manual

Specifications

DTS, DTS-EX, DTX-96/24, DTS High Res, DTS HD Master, DSD
Output video| HDMI
Resolutions supported| Up to 4K2K@50/60Hz (YCbCr 4:4:4), 4K2K@30Hz, all HDMI 3D, etc.
Output video| 18Gbps
Resolutions supported| HDMI Type A 19-pin female
Video amplifier bandwidth| HDMI Type A 19-pin female
Video connector Input Output| 26ft (8m)
Maximum cable length Input Output| 9.8ft (3m)
Operating voltage| 12VDC
Power supply| 1A@12VDC Power adapter
ESD protection (human body model)| ±8kV (air-gap discharge), ±4kV (contact discharge)
Current draw| 320mA@12VDC
Operating humidity| 20~90% (non-condensing)
Operating temperature| 32°~104° F (0°~40° C)
Dimensions| 97/8″x 13/16″x41/8″ (251x20x105 mm)
Weight| 1-lb 6-oz (620g)

Overview

Front Panel – Selector Buttons

Rear Panel

Installation

1. Determine where the HDMI Matrix will be installed in relation to the HDMI sources and displays that the unit will be switching between.
2. Plug the HDMI sources into the HDMI connector inputs on the back of the matrix.
3. Plug the HDMI displays into the HDMI connector output on the back of the matrix.
4. Connect any audio devices such as speakers or an amplifier using optical and/or analog cables.
5. Plug the supplied 12VDC power adapter into the matrix.
6. Turn on the HDMI sources and displays. Use the included remote or selection buttons on the switch to change the HDMI sources going to the corresponding HDMI displays.

Operation

1. Press the Out A and Out B selector buttons to scroll through the 4 inputs and choose which input should be displayed on the corresponding output.
2. Alternately, press and hold either the Out A or Out B buttons for 3 seconds to turn AUTO for that output on (or off). With AUTO on, it automatically chooses the  most recent input for that output.
3. The AUDIO button allows you to select which output’s audio will be sent to the optical and analog audio outputs. If Audio Return Channel (ARC) has also been selected (using the ARC button), the audio will be directed only to the optical output and the analog port will be muted.
4. The 4K1080p button allows you to select one output for which the 4K input will be downscaled to 1080p for a monitor that does not support 4K.
5. The EDID switch on the back of the matrix supports AUTO (selects the best format), COPY (picks the format from the monitor), and STD (picks the format from the  source).
   NOTE: For each button, corresponding blue LEDs will light to indicate the current selection.

Remote Control

The remote control works just like the buttons on the front panel except that all buttons are grouped according to output.
Fig. 1 – Remote Control

1. The Power button turns the matrix on/off or sets it to standby mode.
2. The numbered buttons under Output A and Output B select the input source for that output.
3. The AUTO button turns the auto function on or off for that output (see Operation above).
4. The 4K/HD button turns on the downscale function for that output.
5. In the Audio section, press ARC to turn that function on or off (see Operation above) and the A or B buttons to select the audio source to send to the optical port  (muting the analog L/R port) or, if ARC is turned on, send the chosen source to both ports.

Wiring Diagram

NOTE: The micro-USB port is provided for potential future firmware updates.

Troubleshooting

HDMI device does not function correctly

• Make sure the matrix is powered
• Make sure that all sources and displays are powered
• Make sure that there are no problems with the HDMI sources, HDMI cables, or HDMI displays by plugging a source directly into the display using the HDMI cable
• Make sure that the sources and displays are plugged in to the correct connectors
• Make sure that the HDMI sources are compatible with the HDMI displays

IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and recording audio and video signals. SECO- LARM will not be held responsible for the use of this product in violation of any current laws or statutes.
California Proposition 65 Warning: These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty  installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option. In no  event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2023 SECO-LARM U.S.A., Inc. All rights reserved.

SECO-LARM® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco- larm.com
Phone: 949-261-2999 | 800-662-0800 Email: sales@seco- larm.com
PICHN3MI_MVM-AH42-42Q_230214.docx

References

• La Armería de Madrid - fabricantes de armas y rifles
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>