EOSS ERCB1 2.4G Remote Control Racing Boat User Manual

EOSS ERCB1 2.4G Remote Control Racing Boat

Introduction

Thank you for purchasing the ERCB1 Remote control racing boat. Please ensure that you have read the product manual and instructions in full, prior to use. Failure to do so may result in product failure/damage or incorrect operation and therefore impact the products performance.

Product features

• Maximum speed: 25km/h
• Maximum running time: 15 minutes
• Maximum controlling range: 100 metres
• Charging time: 120 mins
  • 180 degree flip function
  • Low battery warning
• Boat size: 35.5 x 10 x 8.5cm
• Boat weight: 360.5g

Inclusions

• 2.4G Remote control boat
• Remote controller
• Display boat rack
• Li-PO 7.4V 600mAh rechargeable battery

Not included

• 3×1 .5V”AA” alkaline batteries for remote controller

RC boat main structure diagram

Remote Control

Battery installation

Inserting batteries: remove the battery compartment on the back of the remote controller and insert 3×1.5V AA” alkaline batteries, paying attention to the polarity markings in the battery compartment (batteries are not included).

Charging the boats rechargeable battery

USB (standard configuration)

1. Connect the USB end to a computer.
2. Connect the charger plug end of the USB to the battery

The red indicator turns on when charging and goes out when charing is complete. The battery is fully charged after approximately 2 hours.

WARNING

1. Install the batteries in the correct polarity
2. Do not mix old and new batteries.
3. Do not mix different type of batteries.
4. Non-rechargeable batteries cannot be charged.
5. The rechargeable battery must be charged under adult supervision.
6. Only use the USB data cable provided by the manufacturer for charging.
7. The battery charging voltage cannot exceed 9V.

Inserting the rechargeable battery into the boat

1. Open the outer hatch by turning the locking switch to the right or left
2. Open the inner hatch by turning the 3 locking switches
3. Put the Li-PO battery into the battery holder of the hull
4. Connect the power plug to the battery
5. Replace the inner hatch at a diagonal angle to boat body
6. Close the inner hatch by turning the 3 locking switches
7. Replace the outer hatch
8. Close the outer hatch by turning the locking switch

To pair the boat with the remote controller

1. Once the battery is connected to the power boat, place the power boat
   in the water.

2. Turn on the remote control switch button, the remote control LED indicator light flashes continuously and emits a “beep” sound from the controller. Once it successfully pairs with the boat the remote control LED indicator stays on ready for use.

3. When the boats battery, or remote controllers batteries are low, the remote control LED indicator light flashes continuously and emits a “beep” sound. Return the boat to shore, or replace/recharge the batteries

WARNING

1. Please read through the manual before using
2. This product is suitable for people over the age of 14
3. After use, the battery cannot be charged until the battery cools down
4. When recharging, only use the battery charger intended for that purpose
5. Don’t over-charge the battery
6. When using the power boat, insure the area is free of people or debris in the water
7. Keep all body parts away from the spinning propeller to avoid injury
8. Disconnect the power supply from the power boat when not in use
9. The motor can be hot after use. Do not touch it to avoid scalding
10. Regularly, check cables and other parts for damage. Do not use if damaged
11. Please store small parts in a place well out of the reach of small children

Remote control operation

Maintenance

1. After use or storing, disconnect the rechargeable battery.
2. Clean the boats surface with a dry cloth to remove excess moisture.
3. Remove the remote controller batteries to prevent battery leakage and avoid damaging the remote controller.

NB: After play, use a dry cloth to remove any moisture inside the hull and insure the hull is dry. After salt water use clean the boat with fresh water.

Technical assistance

If you need assistance setting up or have an issue regarding the use of your EOSS product contact EOSS Customer Support.
TEL: 03 – 8587 8898 Mon-Fri 9am – 5pm AEST
FAX: 03 – 8587 8866

This manual and product is considered correct at time of printing but is subject to change. For latest manuals and updates refer to the website. TDJ.com.au/help-downloads.
Copyright© 2022 by TDJ Australia

All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, copying or other electronic or mechanical methods, without the prior written permission of the author.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>