KOZEN P10 POS Device User Guide

June 9, 2024
KOZEN

KOZEN P10 POS Device

Product Diagram

KOZEN-P10-POS-Device-FIG-1

NFC Card Reader
NFC antenna locates at the bottom of the screen and on the printer cover. It’s used to sense chip and acquire data through contactless way.

IC Card Reader
Used for inserting the bank chip card and getting information securely.

Magnetic Stripe Card Reader
Used for reading encrypt information stored in corresponding cards.

Camera
Used for taking photos, unlock the device by face recognition and complete intelligent recognition base on it.

Scanner
Used to capture and identify 1D and 2D code.

Power Button
Used for change the running states of device, such as pressing 2~3 seconds to power on/off or screen capture and pressing 10 seconds to restart automatically when device is crashed.

Function Button
Used for adjusting the volume or serving as the shortcut of scan. The function can be customized.

Pogo pin
The 8-pins expanded interface is severed as the channel to connect the charging cradle for better power supply or finish data transmission between different devices.

Hand Stripe Ring
Used to fix the hand strap for easy carrying.

Card Selection Instruction

Printer instructions

  1. Support 2 inch thermal paper roll with specification of 57*40mm (w)
  2. Feed the paper correctly into the paper container in the direction as shown, and pull some paper outside the cutter

Note : If the printed paper is blank, please check whether the pap-er roll has been installed in the correct direction.

Package List

NO. Items list Description
1 Device Default
2 Battery 1pcs,2500mAh/7.6V
3 USB cable 1pcs,1m/2A/type-c
4 User manual Neutral

Technical Specs

Items Specification
Operating System Android 11.0 go
CPU Quad-core@2.0Ghz
Memory 1GB RAM + 8GB ROM (LPDDR3)
Display 6.517” IPS, 720*1600
Camera 2M AF(back) + 2M FF(front)
Scanner E3 Lite
Printer 2 inch thermal printer
Cellular Network Support 2g/3g/4g
WIFI IEEE 802.11a/b/g/n/ac(2.4G/5G)
Bluetooth Version 5.0, support BLE
Payment Magnetic Stripe/NFC/IC Card
Interface USB type-c、Pogo pin(8 pin)
Battery 2500mAh/7.6V (Rated capacity)

ATTENTION

Warning

  • Read all instructions and safety information before use to avoid injury.
  • The limit operating ambient temperature of the device declared by the manufacturer is -10~45°C.

Battery safety

  • Charge battery only at ambient temperatures ranging from 0~40°C.
  • Dispose of used batteries according to manufacturer’s instructions.
  • Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type of battery recommended by the manufacturer.

Statement

  • The equipment damage caused by natural disasters, falling, self disassembly and non-compliance with the operation specifications is not covered by the free warranty.
  • Some details of this document may be inconsistent with the real object due to the update iteration of the product. Please take the real object as the standard, and our company reserves the right to interpret this document.

FCC Regulations

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC R ules. These limits are designed to provide reasonable protection against har mful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in acco rdance with the instructions, may cause harmful interference to radio commu nications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equip ment off and on, the user is encouraged to try to correct the interference by o ne or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/ TV technician for help.

Radio Frequency (RF) Energy
This device is designed and manufactured not to exceed the emission limits f or exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States. The exposure standard for wireless devices employing a unit of measurement is known as the Specific Absorption Rate, or SAR. The SAR limit recomm ended by the general public is 1.6W/kg. Averaged over one gram of tissue b y IEEE Std 1528.The FCC has granted an Equipment Authorization for this product with all reported SAR Levels evaluated as in compliance with the F CC RF exposure guidelines. While there may be differences between the SA R levels of various product and at various positions, they all meet the government requirements.SAR compliance for bodyworn operation is based on a separation distance of 15 mm between the unit and the human body. Carry this device at least 15 mm away from your body to ensure RF exposure level compliant or lower to the reported level. T o support bodyworn operation, choose the belt clips or holsters, which do not contain metallic co mponents, to maintain a separation of 15 mm between this device and your body. RF exposure compliance with any bodyworn accessory, which contains metal, was not tested and certified, and using such body-worn accessory should be avoided.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals