KOZEN D1 Smart POS Device User Guide

KOZEN D1 Smart POS Device

Technical Specs

Panel
Camera| 0.3M FF (for QR code scanning)
Printer| 3 inch Thermal Printer
Cellular Network| Support 2G/3G/4G
WIFI| IEEE 802.11a/b/g/n/ac（2.4G/5G）
Communication| Bluetooth 5.0, support Ethernet
Payment| Support IC/Magnetic/NFC Card
Interface| 4USB-A、1RJ45、1RS232、1RJ12
Battery| Optional

ATTENTION

Warning

• Read all instructions and safety information before use to avoid injury.
• The limit operating ambient temperature of the device declared by the manufacturer is -10~45°C.

Battery safety

• Charge battery only at ambient temperatures ranging from 0~40°C.
• Dispose of used batteries according to manufacturer’s instructions.
• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type of battery recommended by the manufacturer.

Statement

• The equipment damage caused by natural disasters, falling, self disassembly and non-compliance with the operation specifications is not covered by the free warranty.
• Some details of this document may be inconsistent with the real object due to the update iteration of the product. Please take the real object as the standard, and our company reserves the right to interpret this document.

Product Diagram

Display
Main Display is setting for merchants to do commercial settlement, while the second one is setting for show some business information or enter the password to finish the payment.

NFC Card Reader
Used for sensing chip and acquire data through contactless way.

IC Card Reader
Used for inserting the bank chip card and getting information securely.

Magnetic Stripe Card Reader
Used for reading encrypt information stored in corresponding cards.

Scan Window
Used for capturing and identifying QR code when equipped with decode algorithm.

Power Button
Used for change the running states of device, such as pressing 2~3 seconds to power on/off or screen capture and pressing 10 seconds to restart automatically when device is crashed.

Printer Button
Served as the shortcut button to open the printer cover and feed the new paper roll as you need.

Reset Button
Used for restart device instantly as soon as you press the reset button which locates behind the battery cover when device is crashed.

Card selection instruction

Printer instructions

1. Support 3 inch thermal paper roll with specification of 8060mm (wφ)
2. Feed the paper correctly into the paper container in the direction as shown, and pull some paper outside the cutter;

Note: If the printed paper is blank, please check whether the pap-er roll has been installed in the correct direction.

Package List

FAQ

How to connect Wifi on D1？

1. Go Settings-Network & internet-WiFi;
2. Click Wi-Fi, scoll down to choose your Wi-Fi;
3. Enter the password to connect.

How to connect Bluetooth on D1？

1. Go Settings-Connected devices,
2. Click Pair new device;
3. Scoll down the “Available devices”, click your device;
4. Click “pair” on both D1 and your device;
5.  Back to “Connected devices”, click your device in “Previously connected devices” to connect.

FCC warning statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

RF exposure statement
This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter and must be installed to provide a separation distance of at least 20cm from all persons.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>