BRANDCHARGER ASCEND-CHARGE Foldable Magsafe Wireless Charger Phone Stand User Guide
- June 9, 2024
- BrandCharger
Table of Contents
ASCEND CHARGE
FOLDABLE MAGSAFE WIRELESS CHARGER PHONE STAND
MADE FROM RECYCLED PET BOTTLES
Dutch Design – Responsibly Made in China
Applicable devices
ASCEND CHARGE will wireless charge Apple and Samsung devices with wireless charging and other devices with Qi wireless technology.
Accessories
- ASCEND CHARGE x 1 piece
- 1.2m USB to USB-C cable x 1 piece
- User manual x 1 piece
Specification
Input: DCSV/9V
Wireless charging: 15W (Max)
Transmission distance : 5mm
Charging efficiency: 80%
size: 115 X 70 mm
Unit weight: 66g (NW)
Important Notes
- Do not disassemble, attempt to open, or break the product
- Keep away from fire and water
- Do not use in a hot or humid environment to prevent damage and potential harm to the user
- Keep away from items with a magnetic strip or chip card (credit cards, bank cards, etc.)
- This item is not a toy; please keep away from children
- Keep a distance of 20 cm between the product and implanted medical devices to avoid potential interference
- 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
User Manual
Thank you for choosing ASCEND CHARGE and enjoy our product!
Please read the following instructions carefully and keep this manual for
reference.
USB power source (DC 9V/2A)
- Connect the USB-C to the port on the side of Ascend Charge.
- Connect the USB-A to any USB power source.
Charging Mode
1. Place the phone on the magsafe wireless charging pad.
Wireless charging begins. If phone does not charge, check to make sure the
phone is straight on the charging pad.
Product name: ASCEND CHARGE ECO – Foldable magsafe fast wireless charger phone
stand
Dimensions: Spread 395 x 315 x 5 mm
Dutch design, Responsibly made in China
The product contains 50% RCS certified recycled polyester
Certified by ESTS-221329
More info: www.textileexchange.org
FCC statement:
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Radiation Exposure Statement This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co- located or operating in conjunction with any other antenna or transmitter. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of thedevicemust be respected.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>