BERGMEN Facile Pro LED Light User Manual

Facile Pro
USER MANUAL

Facile Pro LED Light

Bergmen® LED light Facile Pro may only be installed and used indoor. Product is dedicated to surface and suspended mounting. Bergmen® LED light Facile Pro has been designed and manufactured according to European and local lighting standards. Facile LED light is not dimmable — product is not adapted to work with dimmer.
The kit consist of:

• LED light with driver built-in,
• mounting accessories: 2 pcs of mounting clips, 2 pcs of wall plugs (8mm), 2 pcs of screw,

If you found the lack of any mentioned elements, you should report this fact to the seller.

Assembly instruction

1. Before the installation you should carefully read recommendations included in the section “Precautions”.
2. Facile LED light is a product ready for installation — the driver is built into the product.
3. Art Neon Lighting is not responsible for damages caused by wrong installation.
4. In case of any problems and doubts you should disconnect the power supply, dismount LED light and consult with a specialist.
5. Before installation you should switch the power off.

Surface mounting

1. Choose place where LED light will be installed.
2. Drill holes on the mounting surface and put wall plugs into. Place the screw into the wall plugs.
3. Fix mounting clips to the ceiling surface using the screw.
4. Install LED light by snapping mounting clips.
5. Make sure that LED light is installed correctly and stable then connect wires to the power source.
6. Switch the power on and check whether the product is working properly.

Special precautions

1. The product should be used for its intended purpose.
2. During the preparation for an installation should be check the compliance of product with an order (model, colour temperature, quantity, etc.) and examine to ensure that it is free from any apparent defects. LED strip or wires damage exclude the product from installation. If damage is found, please contact the seller immediately.
3. The installation should be carried out in accordance with the assembly instructions.
4. The assembly should be carried out by a person with appropriate qualifications. It has to be ensured that the power is off. An installation with the power on can damage product and human health or life.
5. When connecting the product to a power source, it is recommended to use the safety guidelines contained in, among others in the European Standard PN-EN 50110-1: 2013-05.
6. Making independent repairs and modifications results in the loss of the warranty, and also threatens health or life. Detailed information about the guarantee is included in the General Terms and Conditions of Guarantee and General Sales Conditions, documents are available at www.bergmen.pl.
7. Neither the product nor any of its components or packaging elements is a toy. Keep them out of reach of the child. The assembly should not be performed in the company of children.
8. To ensure safe use of the product and its declared lifetime, avoid:
   • shocks, which could lead to the destruction of LEDs;
   • contact with water, dust (adequately to the degree of IP protection specified in the product data sheet), chemicals, lubricants that after penetration into the product could damage its components.

Maintenance and disposal

1. Maintenance should be done with the power switched off after the product has cooled down completely. The product is equipped with a diode / LED light source that is / are not interchangeable.
2. You can clean the outer surface of LED light using dry, clean, soft cotton. Do not use any chemicals. Cleaning can be done only when the power is off.
3. After use return the product to an appropriate licensed drop off point for electrical waste (detailed information available here: https://bergmen.pl/zzsee.pdf)
4. It is not allowed to dispose used product together with household waste.

The marking of the product, layout and trade mark Bergmen are the property of the Bergmen Sp. z o.o. registered partnership, all rights reserved. Bergmen Sp. z o.o. registered partnership is not responsible for any harms and damages caused by wrong performed installation or improper exploitation and misusing product. Before product installation please check general precautions listed on our website www.bergmen.pl/en/download/

Bergmen Sp. z o.o. ul. rtm.
Witolda Pileckiego 4, 32-050 Skawina tel.
0048 12 415 50 50
www.bergmen.pl

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>