BERGMEN Flex Pro LED Strip User Manual

BERGMEN Flex Pro LED Strip

Special precautions

1. The product should be used for its intended purpose.
2. Before an installation product should be checked according to order (model, color temperature, quantity etc.) and tested to ensure that it is free from any defects. Led module or wires damage unqulifies the product to installation. If damage is found, please contact the seller immediately.
3. The installation should be done in accordance with the assembly instructions.
4. The assembly should be done by a person with appropriate qualifications. The power must be off. An installation while power is on may afect damage of product, human health or life
5. While connecting the product to a power source, it is recommended to use the safety guidelines contained in among others the European Standard PN-EN 50110-1: 2013-05.
6. Making repairs and modifications on your own causes losing of the warranty and also threatens health or life. Detailed information about the guarantee is included in the General Terms and Conditions of Guarantee and General Sales Conditions, documents are available at www.bergmen.pl.
7. Neither the product nor any of its component or packaging elements is a toy. Keep them away from children. The assembly should not be done in the company of children.
8. To ensure safe use of the product and its declared lifetime, avoid:
   • shocks, which could lead to the destruction of LEDs,
   • contact with water, dust (adequately to the degree of IP protection specified in the product data sheet), chemicals, lubricants that after penetration into the product could damage its components.

Recommendations

• Before starting the installation, make sure that you have the right constant voltage power supply adjusted to the product (full specification in the data sheet). Connecting the product to a voltage higher than recommended may lead to its irreparable damage.
• Cutting product is allowed only in marked places (Fig. 1.).
• The tape bends in only one plane (in the direction of winding on the roll, fig. 2), bending the tape in other planes and below the defined bending diameter (060) can lead to permanent damage of the product.
• Product assembly is recommended on surfaces that provide free heat dissipation, e.g. aluminum profiles. The type of base affects the declared lifespan of product.
• Due to the equal light in case pieces of strip >3m and Sm power should be provided at least once/ each Sm.
• It is not recommended to use tapes with IP 44-65 in places directly exposed to atmospheric conditions (rainfall, UV radiation, etc.).

Assembly Instruction

1. T Disconnect the power supply.
2. T Thoroughly degrease the mounting surface.
3. Peel off the security paper of the double-sided tape at the bottom of the LED strip (for models not equipped with mounting tape, use mounting brackets and/or glue additionally).
4. Stick/ mount the product on the designated place.
5. Make sure that the LED strip has been correctly mounted and that it is firmly attached to the ground.
6. Connect the product to the power supply according to the attached diagram (Fig 3).
7. Turn on the power and check the operation of the strip.

Maintenance and disposal

1. T Maintenance should be done with the power switched off after the product has cooled down completely. The product is equipped with a diode / LED light source that is / are not interchangeable.
2. T After use return the product to an appropriate licensed drop off point for electrical waste (detailed information available here: https://bergmen.pl/zzsee.pdf)
3. It is not allowed to dispose used product together with household waste.

The marking of the product, layout and trade mark Bergmen”” are the property of the Bergmen Sp. z o.o. registered partnership, all rights reserved. Bergmen Sp. z o.o. registered partnership is not responsible for any harms and damages caused by wrong performed installation or improper exploitation and misusing product. Before product installation please check general precautions listed on our website www.bergmen.pl/en/download/

Bergmen Sp. z o.o.
ul. rtm. Witolda Pileckiego 4, 32-050 Skawina
tel. 004812 415 50 50
www.bergmen.pl

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>