BERGMEN Rueda Professional LED Lighting User Manual

: June 9, 2024
: BERGMEN

Table of Contents

Introduction
Specification
Assembly Instruction
Special Precautions
Maintenance and disposal
Customer Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BERGMEN Rueda Professional LED Lighting

Introduction

Berg men.., Rueda LED down light fitting was designed as a functional and decorative lighting. Product can be mounted and used indoor, in areas exposed to moisture and exposure to water. The lamp has an IP65 protection. The downlight has been designed and manufactured according to European and local lighting standards.

Specification

Model| Product code| LED type| Voltage| Power| Beam angle| Color temp.| Luminous flux| CRI| IP| Operating temp.| Storage temp.| Dimensions| Mounting hole| Weight
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
Rueda| 01-005-042-02-A| Sharp COB| 220-240V AC| 10W| 40º| 3000 K| 820 Im| ≥80| 65| -20~40°C| -20~40°C| Ø83x66mm| Ø70mm| 0.30 kg
Rueda| 07-005-042-04-A| Sharp COB| 220-240V AC| 10W| 40º| 4000 K| 900 Im| ≥80| 65| -20~40°C| -20~40°C| Ø83x66mm| Ø70mm| 0.30 kg

Assembly Instruction

Before the installation you should read carefully recommendations included in the section ‘Precautions”. The fitting is supplied only as the product ready to the installation. It has an external driver, requires connection wires of the driver to the mains supply.

Switch the power off.
Product is a recessed type downlight, you should prepare the mounting hole with the diameter given in the attached product specification.
Connect power wire.
Deflect mounting springs and place the fitting in the mounting opening prepared previously, latch springs inside the opening.
Make sure that the fitting is mounted correctly and that mounting latches keep the fitting in the stable way. Twist the bezel element on the lamp according to a clockwise direction.
Switch the power on and check the operation of the fitting.

Bergmen Sp. z o.o. is not responsible for damages caused by wrong installation. In case of any problems and doubts you should consult with a specialist.

Special Precautions

The product should be used for its intended purpose.
Before an installation product should be checked according to order (model, color temperature, quantity etc.) and tested to ensure that it is free from any defects. Led module or wires damage unqualifies the product to installation. If damage is found, please contact the seller immediately.
The installation should be done in accordance with the assembly instructions. In lack of manual user inside box product, in order to proper installation please contact your sales representative.
The assembly should be done by a person with appropriate qualifications. The power must be off. An installation while power is on may afect damage of product, human health or life
While connecting the product to a power source, it is recommended to use the safety guidelines contained in among others the European Standard PN-EN 50110-1: 2013-05.
Making repairs and modifications on your own causes losing of the warranty and also threatens health or life. Detailed information about the guarantee is included in the General Terms and Conditions of General Sales Conditions, available at www.bergmen.pl.
Neither the product nor any of its component or packaging elements is a toy. Keep them away from children. The assembly should not be done in the company of children.
To ensure safe use of the product and its declared lifetime, avoid:

shocks, which could lead to the destruction of LEDs,
contact with water, dust (adequately to the degree of IP protection specified in the product data sheet), chemicals, lubricants that after penetration into the product could damage its components.

Maintenance and disposal

Maintenance should be done with the power switched off after the product has cooled down completely. The product is equipped with a LED light source that is not interchangeable.
You can clean the outer surface of LED light using dry, clean, soft cotton. Do not use any chemicals. Cleaning can be done only when the power is off.
After use return the product to an appropriate licensed drop off point for electrical waste (detailed information available here: https://bergmen.pl/zzsee.pdf)
It is not allowed to dispose used product together with household waste.

The marking of the product, layout and trade mark Bergmen”‘ are the property of the Bergmen Sp. z o.o. registered partnership, all rights reserved. Bergmen Sp. z o.o. registered partnership is not responsible for any harms and damages caused by wrong performed installation or improper exploitation and misusing product. Before product installation please check general precautions listed on our website www.bergmen.pl/en/download/