AC INFINITY IONBEAM S11 Full Spectrum LED Grow Light Bars User Manual
- June 9, 2024
- AC Infinity
Table of Contents
IONBEAM
GROW LIGHT BAR SYSTEM
USER MANUAL1
IONBEAM S11 Full Spectrum LED Grow Light Bars
WELCOME
Thank you for choosing AC Infinity. We are committed to product quality and
friendly customer service. If you have any questions or suggestions, please
don’t hesitate to contact us. Visit
www.acinfinity.com and click contact for our
contact information.
EMAIL support@acinfinity.com
WEB www.acinfinity.com
LOCATION Los Angeles, CA
MANUAL CODE NE2201X1
PRODUCT
IONBEAM S11
IONBEAM S16
IONBEAM S16-UV| MODEL
AC-NES11
AC-NES16
AC-NEU16| UPC-A
819137023352
819137023369
819137023475
---|---|---
PRODUCT WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
- Ensure your power source conforms to the electrical requirements of this product.
- Read all instructions before installing and using this product.
- Be careful not to damage or cut the wire insulation (covering) during the installation. Do not permit wires to come in contact with any sharp edges.
- If you are unfamiliar or have doubts about performing this product’s installation, seek the services of a qualified, trained, and licensed professional. Inappropriate installation will void this product’s warranty.
- This product must not be used in potentially hazardous locations such as flammable, explosive, chemical-laden or wet atmospheres.
- Do not cover power cords with rugs or other fabric materials.
- Safety precautions should be exercised during the installation, operation, and maintenance of this product.
- Do not block or tamper with this product in any manner while it is in operation as it may cause electric shock, fire, or damage to this product.
- Do not depend on the on/off programming as the sole means of shutting power from this product. Unplug the power cord before installing, servicing, or moving this product.
- Do not operate this product while its cord is damaged, or if it malfunctions, has been dropped, or is damaged in any manner.
- Do not stare directly at the LED lighting fixture. Doing so can cause damage to your eyes and compromise your eyesight.
KEY FEATURES
PRODUCT CONTENTS
(X) = Full Spectrum Models, [X] = Ultra-Violet Model
INSTALLATION
LIGHT BAR CHAIN ASSEMBLY
STEP 1
Connect the single-corded LED light bar’s female port to the dual-corded LED
light bar’s male connector.
Repeat this with as many light bars as needed.
STEP 2
Connect the light controller’s male connector to the other end of the dual-
corded LED light bar.
STEP 3
Connect the power adapter to the light controller.
EXTENDING THE CHAIN
You may connect the included bar extension cord in between any link in this
light bar chain to lengthen it. Secure all connections using the twist-on
pieces.
LIGHT BAR MOUNTING
POLE MOUNTING
You may magnetically mount the light bar(s) directly on your grow tent steel
pole.
You may also use the included hook and loop cable ties around the light bar(s)
and mounting bar to adjust the lighting angle and for extra security.
CANVAS MOUNTING
You may magnetically mount the light bar(s) to the wall or ceiling of your
grow tent.
Set the included mounting bar(s) on the outer side of your tent. Place the
light bar(s) at the exact spot on the inner side.
Once mounted, you can move the light bar and mounting bar connection along
your grow tent surface as needed.
STEP 1 — WALL MOUNTING
Make sure your mounting area is free from obstruction. Use a mounting bar to
mark your drilling holes with the logo facing the wall.
STEP 2 — WALL MOUNTING
Drill holes into the marked locations.
STEP 3 — WALL MOUNTING
If you are mounting onto anything other than a wood support or stud, insert
the included four wall anchors into the drilled mounting holes.
You may need to use a hammer to secure them through the holes.
STEP 4 — WALL MOUNTING
Align the mounting bar holes with the wall anchors, making sure the logo faces
the wall.
Screw or drill in the wood screws to secure the mounting bar.
Repeat steps 1-4 as needed.
STEP 5 — WALL MOUNTING
Set the light bar(s) magnet ends onto the mounting bar(s).
CONTROLLER MOUNTING
MAGNET MOUNTING
You may magnetically mount the light controller onto any steel surface.
STEP 1 — WALL MOUNTING
Locate a spot free of obstruction and secure the anchor into your wall. Twist
the wood screw into the anchors.
STEP 2 — WALL MOUNTING
Use the mounting hole located on the back of the controller for wall mount.
POWERING
STEP 1 Plug the power adapter into a wall outlet.
PROGRAMMING
-
LIGHTING
Pressing the light button will increase the light intensity level in 10/30/60/100% increments, displayed with white LED indicators. Pressing this button at 100% intensity will cycle to 0%. Holding the light button will shut off the lighting. Pressing it again will return the light intensity to its previous setting. -
TIMER
Pressing the clock button will set the timer in 3/6/12/18-hour increments, displayed with orange LED indicators.
Within a 24-hour cycle, lighting will be active for the amount of time set here (ex. 3 hours for a 3HR timer). It will deactivate for the rest of the
24-hour cycle (ex. 21 hours).
Pressing the clock button at the 18HR setting will deactivate the timer, cycling from 3HR onwards when pressing this button again. -
UIS CONNECTION
Refer to the programming section of your selected UIS controller for programming instructions.
STARTER GUIDE
FULL SPECTRUM LIGHTING
The charts below offer suggested mounting heights and light intensities for
each stage in the growing process. These factors will vary based on the plant
you are growing. Height refers to the minimum recommended distance from the
canopy (tip of the plant) to the light.
| GROW STAGE | Height | Intensity | Set-Up |
|---|---|---|---|
| Seedling Stage | 1 IN. | ||
| Vegetative Stage | 2 IN. |
*Also recommended for plant propagation.
| GROW STAGE | Height | Intensity | Set-Up |
|---|---|---|---|
| Vegetative Stage | 6 IN. |  | |||
| Flowering Stage | 6 IN. |
SETTING ACTIVE LIGHTING TIMERS
The included controller can set timers in 3/6/12/18-hour increments.
Use either the 3HR or the 6HR timer to extend your plant’s daily exposure to
light, in conjunction with natural sunlight, or when growing plants that don’t
require extended exposure to lighting.
Use either the 12HR or the 18HR timer to complement common light cycles used to grow high yield plants indoors. This will also allow for your lighting to sync with your grow set-up’s existing lighting, so that they may activate at the same time.
CONNECTING TO UIS™
AN INTERCONNECTED GROW SETUP
The Universal Infinity System (UIS) is a series of controllers and devices
that come together to create a fully automated system. UIS enables our
controllers to simultaneously connect with various grow equipment such as
inline fans, clip-on fans, and grow lights. Advance UIS controllers can
provide each connected UIS device with their own automated programming like
temperature, humidity, cycles, schedules, and dynamic levels, while also
pairing with the AC Infinity app.
IONBEAM LED grow lights can connect with select smart controllers as part of an integrated system using the included UIS extension cord.
CONNECTING TO UIS CONTROLLERS
Use the included UIS M-M extension cord to connect the LED light bar(s) to
your selected UIS controller via the light controller’s side port.
Your selected UIS controller will override all of the light controller’s onboard settings when connected in this manner.
AC INFINITY PRODUCTS
Advance Grow Tents
The CLOUDLAB series is a line of grow tents designed to create ideal growing
conditions and facilitate indoor plant cultivation year-round. Features 2000D
thick oxford canvas lined with inner diamond patterned Mylar that maximizes
grow light luminosity, and a reinforced frame with 150 lb. weight capacity.
Includes a mounting plate to install your AC Infinity controller onto.
Humidity Dome
The humidity dome is designed to maintain moisture levels to create the ideal
environment for seed germination. Each kit includes a base tray and seedling
tray with a dome that is built with adjustable vents to control humidity
levels. Height extender also included to provide a higher ceiling for
propagation applications.
Seedling Mats
The SUNCORE series is a line of seedling mat designed to improve germination
success and accelerate your seeds’ growth process by emitting steady heat.
Each mat is lined with an innovative far-infrared film that provides even
heating distribution.
Discover the latest innovations in cooling and ventilation at acinfinity.com
WARRANTY
This warranty program is our commitment to you, the product sold by AC
Infinity will be free from defects in manufacturing for a period of two years
from the date of purchase. If a product is found to have a defect in material
or workmanship, we will take the appropriate actions defined in this warranty
to resolve any issues.
The warranty program applies to any order, purchase, receipt, or use of any
products sold by AC Infinity or our authorized dealerships. The program covers
products that have become defective, malfunctioned, or expressively if the
product becomes unusable. The warranty program goes into effect on the date of
purchase. The program will expire two years from the date of purchase. If your
product becomes defective during that period, AC Infinity will replace your
product with a new one or issue you a full refund.
The warranty program does not cover abuse or misuse. This includes physical
damage, submersion of the product in water, incorrect installation such as
wrong voltage input, and misuse for any reason other than its intended
purpose. AC Infinity is not responsible for consequential loss or incidental
damages of any nature caused by the product. We will not warrant damage from
normal wear such as scratches and dings.
For more information about our dealers and distributors, please contact our
customer service at support@acinfinity.com or
626-838-4656 Monday to Friday (9:00 am
to 5:00 pm PST).
If you have any issues with this product, contact us and we’ll happily resolve
your problem or issue a full refund!
COPYRIGHT © 2022 AC INFINITY INC. ALL RIGHTS RESERVED
No part of the materials including graphics or logos available in this booklet
may be copied, photocopied, reproduced, translated or reduced to any
electronic medium or machine readable form, in whole or in part, without
specific permission from AC Infinity Inc.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>