Honeywell AD355(A) ADAPT Multi Sensor Low Profile Intelligent Detector Owner’s Manual

Honeywell AD355(A) ADAPT Multi Sensor Low Profile Intelligent Detector

Owner

General

The AD355(A) ADAPT® detector is an intelligent, addressable, multi-sensing, low-profile detector designed for use with Fire•Lite Fire Alarm Control Panels. The ADAPT detector uses a combination of photoelectric and thermal sensing technologies to increase immunity to false alarms. Unlike traditional intelligent detectors, the ADAPT detector has a microprocessor in the detector head that processes alarm data. As a result, the ADAPT detector adjusts its sensitivity automatically, without operator intervention or control panel programming. Areas where the ADAPT detector is especially useful include office complexes, schools, college campuses, manufacturing and industrial facilities, and anywhere else the use of a particular area may change. The ADAPT detector automatically adjusts its sensitivity to the environment. LiteSpeed™ is a communication protocol developed to greatly enhance the speed of communication between analog intelligent devices and compatible systems. Intelligent devices communicate in a grouped fashion. If one of the devices within the group has new information, the panel’s CPU stops the group poll and concentrates on single points. The net effect is response speed greater than five times that of earlier designs.

Features

• Automatically adjusts sensitivity levels without operator intervention or programming. Sensitivity increases with heat.
• Microprocessor-based, combination photo and thermal technology.
• Compatible with LiteSpeed™ and CLIP systems.
• Addressable-analog communication.
• Sleek, low-profile design.
• Two-wire SLC connection.
• Rotary, decimal addressing: 01-159 with MS-9600UDLS and MS-9600LS series systems, and 01-99 with MS- 9200UDLS(C) Firmware 4.
• Addresses can be viewed and changed without electronic programmers.
• Dual bi-color LED design provides 360° viewing angle.
• LEDs lock red when in alarm. In LiteSpeed™, LEDs flash green in standby for normal condition.
• Built-in tamper-resistant feature.
• Constructed of off-white fire-resistant plastic, designed to commercial standards, and offers an attractive appearance.
• SEMS screws for wiring of the separate base.
• Several base options, including relay, isolator, and sounder.
• Built-in functional test switch activated by external magnet.
• Listed to UL 268.

Specifications

• Sensitivity: auto-adjusting levels: 1 to 2%/ft. and 2 to 4%/ft.
• with classic CLIP systems; 1 to 2, 2 to 3, and 3 to 4%/ft. with
• LiteSpeed™ systems; fixed-sensitivity levels: 1, 2, and 4%/ft.
• with classic CLIP systems; 0.5, 1, 2, 3, and 4%/ft. with FlashScan systems.
• Size: 2.0″ (5.3 cm) high; base determines diameter.
• B210LP(A): 6.1″ (15.5 cm) diameter.
• B501(A): 4.1″ (10.4 cm) diameter.
• B200SR(A): 6.875″ (17.46 cm) diameter.
• B224RB(A): 6.2″ (15.748 cm) diameter.
• Shipping weight: 5.2 oz. (147 g).
• Operating temperature: 0°C to 38°C (32°F to 100°F).
• UL-Listed velocity range: 0 – 4000 ft./min. (1219.2 m/min.), suitable for installation in ducts.
• Relative humidity: 10% – 93% noncondensing.
• Thermal sensing rating: fixed-temperature setpoint 135°F (57°C).

ELECTRICAL SPECIFICATIONS

• Voltage range: 15 – 32 volts DC peak.
• Standby current (max. avg.): 300 μA.
• Loop resistance: 50 ohms maximum; varies according to control panel used. Refer to panel installation manuals.
• LED current (max.): 6.5 mA @ 24 VDC (“ON”).

Installation

The AD355(A) plug-in detector uses a separate base to simplify installation, service, and maintenance. A special tool allows maintenance personnel to plug- in and remove detectors without using a ladder. Suitable mounting base boxes include:

• 4.0″ (10.16 cm) square box.
• 3.5″ (8.89 cm) or 4.0″ (10.16 cm) octagonal box.
• Single-gang box (except relay or isolator base).

NOTE: The AD355(A) detector has the unique ability to adjust sensitivity according to the environment, based on heat and smoke levels. Avoid installing these detectors in locations that are susceptible to rapid and high temperature changes. An example of an incorrect application would be near or in line with the output of a self-contained heater.

Agency Listings and Approvals

These listings and approvals apply to the modules specified in this. In some cases, certain modules or applications may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing status.

• UL Listed: S1059.
• ULC Listed: S1059.
• MEA Listed: 243-02-E.
• FM Approved.
• CSFM: 7272-0075:0194.

Ordering Information

• NOTE: “A” suffix indicates ULC Listed model.
• AD355: Low-profile intelligent multi-sensor detector.
• AD355A: Same as AD355 but with ULC Listing.

INTELLIGENT BASES

• NOTE: “A” suffix indicates ULC Listed model.
• NOTE: The detector’s plug-in base can be changed off for special applications. For details about intelligent bases and their mounting, see DF-60059.
• B210LP(A): Plug-in detector base (included); standard U.S. flanged low-profile mounting base.
• B210LPBP: Bulk pack of B210LP; package contains 10.
• B501(A): Flangeless mounting base.
• B501BP: Bulk pack of B501; package contains 10.
• B200SR(A): Intelligent sounder base capable of producing sound output with ANSI Temporal 3 or continuous tone. Replaces B501BH series bases in retrofit applications.
• B224RB(A): Relay base Screw terminals: up to 14 AWG (2.0 mm²). Relay type Form-C. Rating: 2.0 A @ 30 VDC resistive; 0.3 A @ 110 VDC inductive; 1.0 A @ 30 VDC inductive.
• B224BI(A): Isolator base. Maximum: 25 devices between isolator bases.

ACCESSORIES

• F110: Retrofit flange to convert B210LP to match the B350LPB350LP profile, or to convert older high-profile bases to low-profile.
• F110BP: Bulk pack of F110; package contains 15.
• F210: Replacement flange for B210LP(A) base.
• RA100Z(A): Remote LED annunciator. 3 – 32 VDC. Fits U.S. single-gang electrical box. Supported by B210LP(A) and B501(A) bases only.
• SMB600: Surface mounting kit for use with B210LP(A).
• M02-04-00: Test magnet.
• M02-09-00: Test magnet with telescoping handle.
• XR2B: Detector removal tool. Allows installation and/or removal of LiteSpeed™ Series detector heads from base in high ceiling installations.
• T55-127-010: Detector removal tool without pole.
• XP-4: Extension pole for XR2B. Comes in three 5-foot (1.524 m) sections.

ADAPT® and Fire•Lite are registered trademarks and LiteSpeed™ is a trademark of Honeywell International Inc. ©2011 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact Fire•Lite Alarms. Phone: 800-627-3473, FAX: 877-699-4105. www.firelite.com firealarmresources.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>