SIEMENS EL-410D Audio Amplifier Instruction Manual

SIEMENS EL-410D Audio Amplifier

MODEL EL-410D
Audio Amplifier for CPV90: AT-EX and AT-1 and, for the MXLV Voice Equipment
(Note: The CPV90 is listed per UL864 8th Edition only)

INTRODUCTION

The model EL-410D audio amplifier from Siemens Industry, Inc., may be used in the CPV90 Voice Alarm System (Refer to the CPV90 Manual, P/N 315-081079) as well as in the MXLV System
(Refer to the MXL/MXLV Manual, P/N 315-092036). It is rated at 100 watts for either a 25V RMS output or a 70.7V RMS output.

• When EL-410D is used in a CPV90 System, choose only the 70.7V RMS output terminal of the EL-410D. Place a jumper between the COM terminal and terminal 16 as shown in Figure 1.
• When EL-410D is used in an MXLV Sys-tem, choose an amplifier output of either 25V RMS or 70.7V RMS by selecting the appropri-ate amplifier terminal for the connection. DO NOT USE the jumper between the COM terminal and terminal 16 with the MXLV System.
• When the EL-410D amplifier does not require battery backup, connect the resistors as shown in Figure 4 (page 4) to override the battery super-vision fault condition.

CPV90 VOICE ALARM SYSTEM CONNECTIONS

EL-410D amplifiers using the AT-1 and the AT-EX Transfer modules in a CPV90 System can be backed up on a one-to-one basis, or multiple amplifiers can share a common backup.

• The one-to-one amplifier backup setup requires an AT-1 Transfer module for the active amplifier and its backup amplifier.
• When two or more active amplifiers are used with a single backup amplifier, the AT-1 and AT-EX modules are both required.
• When an installation requires multiple channels, separate amplifiers or separate groups of amplifiers (along with their transfer modules AT-1 and AT-EX) are required for each channel of operation.

Figure 1 shows the typical wiring for the EL-410D in a CPV90 System for a single amplifier (100 watts output) without backup. Figure 2 shows the typical wiring for the EL-410D in a one-channel CPV90 System with multiple amplifiers (more than 100 watts output) and a single backup.

Siemens Industry, Inc. Building Technologies Division Florham Park, NJ
P/N 315-094916-8

Siemens Building Technologies, Ltd. Fire Safety & Security Products
2 Kenview Boulevard
Brampton, Ontario
L6T 5E4 Canada

WITH CPV90 SYSTEM ONLY (NOT FOR MXLV)

Adjustment of AT-1/AT-EX

(The adjustment potentiometers R33 and R34 are preset at the factory; however, if the problem described below occurs, the following procedures may be used to correct the problem.)

The AT-1 and its extender, the AT-EX, compare the low level audio input signal of a specific audio channel to that of the amplified output level of each amplifier on that channel. When the compared output level of that amplifier is below that of the factory preset value, the modules transfer the output power from that amplifier to that of a backup amplifier. Such a transfer is indicated when the related yellow LED on the module lights as follows:

 | AT-1/AT-EX

Audio Input Screw Terminal

---|---
1| 3
Trouble LED| DS-1| DS-2
Adjustment Pot| R33| R34

WITH CPV90 SYSTEM ONLY (NOT FOR MXLV)

Figure 2
CPV90 Wiring – Any One Channel, Multi-Amplifier, with Single Backup

NOTES

1. Use only the AT-1 for one-to-one backup of the EL-410D.
2. The connection shown is for an even number of active amplifiers. When an odd number of active amplifiers are used, connect the audio output of the last active amplifier (terminal 70V) to AT-EX, terminal 3, and the audio output to the System from AT-EX, terminal 4.
3. The audio output from the AT-EX connects to the VMN-310/50. The VMN-310/50 controls the speaker zones that the amplifier powers. The VMN-310 has two sets of connectors, D1 and D2. Each set of connectors has a terminal 0 as the common, and terminals A, B, and C, which are available for audio channels.
   (Refer to the CPV90 Voice Alarm manual, P/N 315-081079.) Since each card on the VMN-310 uses 20W (or on the
   VMN-310/50, 50W), one amplifier connected to D1 covers five speaker zones. If more than 100W are used by a VMN-310, connect an additional amplifier to D2 and cut the appropriate jumpers determined by the speaker zone load distribution.
   For multi-channel conflguration, refer to the CPV90 Voice Alarm manual, P/N 315-081079, Table F and Figures 3-4 through 3-6.

CHECKOUT AND ADJUSTMENT PROCEDURE OF THE POTS

1. Rotate the potentiometer indicated above completely clockwise. After a few seconds delay, the module transfers back to a normal untransferred condition.

2. With the System in full load operation (ALL EVACUATION or ALL ALERT), measure the RMS voltage at the input terminal in question. If the measured value is less than 80% of the expected value, investigate the amplifier or input signal(s).
   Note: Operation of the All Call or message unit results in a voltage that is not constant, which presents a measure-ment problem for this step.

3. Readjustment of the transfer level:

   • With the System not operating, connect the attenuation network (as shown in Figure 3) to the required input circuit and terminal.
   • With the System in full operation (Step 2), slowly adjust the related pot counter-clockwise until transfer occurs. Leave the pot at this setting. If that particular module receives a lot of vibration, seal the pot with a substance such as liquid solder, etc.
   • Remove the attenuation network. Re-connect the amplifier output to its previous connection.

MXLV BATTERY CALCULATIONS

When using the EL-410D amplifier in MXLV Systems, include EL-410D power requirements when calculating battery backup size (Refer to the MXLV Manual, P/N 315-092036).

1. Account for all amplifiers in the system.
   • There is one for each audio channel.
   • There are backup ampifiers, if required.
2. Based upon the application, determine:
   • The number of amplifiers the system uses.
   • The number of active amplifiers during an alarm condition.
3. Follow the guidelines in the MXLV Manual, P/N 315-092036, for overall system battery requirements.
4. Add the speaker power requirements in watts for all audio zones. Determine the power for each speaker by the placement of the jumper wire on the PC board on the back of the speaker. Refer to the speaker installation sheet, if necessary. This is the total amplifier power with all speaker zones active.
5. Standby current for the EL-410D amplifier is 0.200 ampere. Active current varies with the speaker load on the output. Refer to Table 1.

MXLV VOICE SYSTEM CONNECTIONS

(Refer to Figures 5 and 6, pages 6 and 7, for wiring diagrams of an MXLV application.)
When using a System 3 enclosure to install EL-410D modules, use the following items:

EB series System 3 backbox
EK series System 3 rail assemblies
ED series System 3 door
Single space blank plate for door—P/N 305-087493 or, eight space blank plate for door—P/N 225-180696

TABLE 1

EL-410D ACTIVE CURRENTS FOR BATTERY CALCULATIONS

Output Power (Watts)| Battery Current (Amperes)
10| 1.3
20| 2.3
30| 3.3
40| 4.3
50| 5.3
60| 6.2
70| 7.2
80| 8.2
90| 9.2
100| 10.0

ELECTRICAL RATINGS

3A max.

When using an MME-3 or MLE-6 enclosure to install the EL-410D, use these items:

MME-3 or MLE-6 enclosure (includes backbox and door)
MSR-1 Rail Kit
MDG-1 Plate

Notes for Figures 5 and 6

1. For information on the riser connections refer to the following appropriate documentation as necessary:
   • MXLV Manual P/N 315-092036
   • OCC-1 Instructions P/N 315-090918
   • ASC-1 Instructions P/N 315-091263
   • ASC-2 Instructions P/N 315-092085
2. Run the low level audio input lines from the OCC-1 in shielded cable and separate conduit from the high level audio output lines of the amplifiers. See OCC-1 Instructions, P/N 315-090918.
3. If multiple EL-410Ds are used, connect the EL-410Ds together using terminals 7 and 8. Then connect them to the OCC-1. This supervises the battery and AC fault at the EL-410D. If there is no battery connected to the EL-410D, this wiring configuration is not necessary.
4. Configure the OCC-1 input with CSG-M (AccuLINK) for normally low 5/24 VDC input. The EL-410D power/battery supervision is normally low input.
   Refer to Wiring Specification for MXL, MXL-IQ and MXLV Systems, P/N 315-091772 revision 6 or higher, for additional wiring information.

Siemens Industry, Inc.
Building Technologies Division Florham Park, NJ
P/N 315-094916-8

Siemens Building Technologies, Ltd.
Fire Safety & Security Products
2 Kenview Boulevard
Brampton, Ontario
L6T 5E4 Canada

firealarmresources.com

References

• Fire Alarm Resources | Download fire alarm documents

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>