Shenzhen Fitcare Electronics BX100 Boxing Punch Tracker User Manual

Shenzhen Fitcare Electronics BX100 Boxing Punch Tracker

This manual describes the features and usage of the product. Please read this manual carefully before using the sensor.

Product Specifications

• Product Size: 65 47 16 mm (Charge box)
• Product Weight: 12g (Sensor L&R)
• Battery: 40mAh
• Battery Life: 25 Hours
• Working Temperature: 0°C ~ 40°C
• Communication Mode: ANT+ and BLE

Product Accessories

• 2x Sensor
  

• Charging Box
  

• USB Cable
  

• User Manual
  

• 2x Wrist Strap
  

Button and Indicator description

1. Short press the power button to turn on the device, the green light will start to flash. Press the power button again to turn off the sensor, the sensor will turn off after the green and blue light flash alternately for several times.
2. When the green light flashes, it means Bluetooth is not connected, when the blue light flashes means Bluetooth is connected.
3. When the red light flashes, the battery is running low.
4. The red and green light will flash alternately while charging. After fully charged, the green light will stay on.

Charging

put the senses into the corresponding slot in the charging box (‘L’ for left sensor, ‘R’ for right sensor), connect the charging box and the adaptor with USB cable. The red and green light flashing alternately means the sensor is in charging state, when the green light stays on means the sensor is fully charged.

Connect with APP

1. Please search for FlashLightPro in Google Play or the App Store to download the App.
2. Open the FlashBackPro app (requires Bluetooth to be turned on on your phone) to connect the sensor.
3. Short press the power button to turn on the device (indicator light flashing).
4. In the app pairing list, select the corresponding ID (left ‘L’ / right ‘R’) to for pairing, after connected successfully, enter the training page.

Wearing

Wearing the sensor correctly will maximum the accuracy for the device.

• please pay attention to simple ‘L’ and ‘R’ when wearing.
  As the picture shows:

  1. Put the sensor into the strap
     

  2. Adjust the length of the strap, and tied into comfortably to your wrist.
     

Start Training

1. Make sure you follow the instructions above.
2. The training want you need (quick start, round training) to start your boxing training. The FlashLightPro App will automatically record your punch data.
3. If your sensor is disconnected from the app during the training, you can reconnect and find the lost data in “me” in the App, the sensor can save the data for the last 300 punches.

Compatible Model

1. iOS 8.0 or higher system version, iPhone 5 and above models.
2. Android phone: Android 4.3 and above, and BLE 4.0.

Disclaimer

The information provided in this manual is for informational purposes only E and the device are subject to change without notice because of the manufacturer’s continuous research and development.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>