SUNCO LIGHTING WP-120W-5K-1PK 120W Wall Pack Installation Guide

The Brighter Choice
120W WALL PACK

Install Guide and Manual

COMPONENTS

EASY INSTALLATION

JUNCTION BOX INSTALLATION

| PRIOR TO INSTALL:
• Prepare trim plate by removing knockouts.
• Prepare backplate by removing center knockout.| REQUIRED TOOLS:
Drill, Philips Screwdriver, Flathead Screwdriver, Junction Box, Caulking Tool & Caulk, Wire Stripper/Cutters
---|---|---

| 1. Turn off power at fuse or circuit breaker before installing or servicing.
• If you are replacing an existing HID/HPS fixture, allow fixture to cool before removing from the wall.
2. Open cover by unscrewing 2x door screws on side of wall pack, then lift off pinned hinges.
• Disconnect TP24 connector, if connected.
---|---
| 3. Drill 2x holes in base plate to match J-Box holes.
4. Use internal level to position wall pack on wall.
| 5. Slide trim plate between wall and back plate.
• Pull supply wires through center hole.
6. Align 2x holes in base plate with junction box.
Secure base plate with 2x screws to wall.
| 7. Connect internal wires to power supply using 3x wire nuts.
• Live to Live (black);
• Neutral to Neutral (white);
• Ground to Ground (yellow/green)
| 8. Seal 3x open holes with waterproofing material, such as caulk (not included).
| 9. Slide cover onto base plate.
10. Connect TP24 connector.
11. Secure cover to back plate with 2x door screws.
• Ensure no wiring is pinched.
12. Turn ON power to verify successful installation.

WARNING

To reduce the risk of fire, electric shock or injury to people:

• This product should be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
• Abide by related regional and local laws or regulations.
• Proper grounding is required to ensure safety.
• Check for damage during shipping prior to install. If the product is damaged, do not use it.
• Turn off the switch and circuit breaker before installing this LED light fixture.
• Use safety precautions. Safety eyeglasses and gloves are recommended.
• Please review instructions carefully before proceeding.

J-BOX COMPATIBILITY

This fixture is compatible with 4” octagon / square / round and 3.5” round new work / round old work junction boxes.
Our Wall Pack base plate includes 8 potential drilling holes. The outside circle includes a 3.54” (90mm) distance between holes. The inner circle holes are 2.76” (70mm) apart.

DIRECT MOUNT WITH CONDUIT

| PRIOR TO INSTALL:
• Prepare trim plate by removing knockouts.
• Prepare backplate by removing center knockout.| REQUIRED TOOLS:
Drill, Philips Screwdriver, Flathead Screwdriver, Junction Box, Caulking Tool & Caulk, Wire Stripper/Cutters
---|---|---

| 1. Turn off power at fuse or circuit breaker before installing or servicing.
• If you are replacing an existing HID/HPS fixture, allow fixture to cool before removing from the wall.
2. Open cover by unscrewing 2x door screws on side of wall pack, then lift off pinned hinges.
• Disconnect TP24 connector, if connected.
---|---
| 3. Drill 3x holes in base plate (A, B, C).
IF REPLACEMENT: Skip to step #7.
IF NEW INSTALL:
4. Use internal level to position base plate on wall.
Mark 3x drill points on wall to match baseplate holes (A, B, C).
5. Drill 3x holes in wall.
6. Add 3x wall anchors in drilled holes.
| 7. Slide trim plate between base plate and wall.
8. Pull supply wires through center hole.
9. Align 3x holes in base plate with wall anchors.
Secure base plate with 3x screws to wall.
| 10. Connect internal wires to power supply using 3x wire nuts.
• Live to Live (black);
• Neutral to Neutral (white);
• Ground to Ground (yellow/green)
| 11. Seal 4x open holes for waterproofing with caulk (not included).
| 12. Slide cover onto base plate.
13. Connect TP24 connector.
14. Secure cover to back plate with 2x door screws.
• Ensure no wiring is pinched.
15. Turn ON power to verify successful installation.

WARNING
To reduce the risk of fire, electric shock or injury to people:

• This product should be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
• Abide by related regional and local laws or regulations.
• Proper grounding is required to ensure safety.
• Check for damage during shipping prior to install. If the product is damaged, do not use it.
• Turn off the switch and circuit breaker before installing this LED light fixture.
• Use safety precautions. Safety eyeglasses and gloves are recommended.
• Please review instructions carefully before proceeding.

SPECIFICATIONS

Documents / Resources

| SUNCO LIGHTING WP-120W-5K-1PK 120W Wall Pack [pdf] Installation Guide
WP-120W-5K-1PK 120W Wall Pack, WP-120W-5K-1PK, 120W Wall Pack, Wall Pack, Pack
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>