touchstone 80033 Chesmont Series Electric Fireplace Owner’s Manual

CHESMONT SERIES ELECTRIC FIREPLACE MANTEL
Model # :
80033 – Chesmont White
80034 – Chesmont Black
OWNER’S MANUAL

AC 110-120V 60Hz 1500W

WARNING Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in fire, electric shock, or serious personal injury.
**CAUTION** Keep this owner’s manual for future reference. If you sell or give this product away, make sure this manual accompanies this product.

General Information

CSA Approval Listing Information

This fireplace has been tested in accordance with the CSA Standards for fixed and location-dedicated electric room appliances in the United States and Canada. If you need assistance during installation, please contact our technical support department at 800-215-1990 option 2.
Note: This fireplace must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition in the United States or the Canadian Electric Code, CSA C22.1 in Canada.

Fireplace Specifications

Dimensional Drawings
80033/80034 – Dimensions

80033 – Chesmont Wall Mounted Electric Fireplace – Black 80034 – Chesmont Wall Mounted Electric Fireplace – White
Features
– 2 heat settings (high and low)
– Programmable thermostat
– 68F to 88F
– Designed for wall mounting
– Remote control for heat and flame setting (batteries not included)
– 3 flame color settings – orange, blue, blue/orange
– Dual mode, operates with or without heat for only flame effect
– Built in timer mode up to 8 hours
– Faux Fire Log and Glass Crystal Media Options
Specifications
– Frame color: 80033
– White 80034 – Black
– Watts: 1,500
– BTU’s: 5,000
– Room Coverage: 400 ft.
– Voltage: 110v-120v
– Amperes: 12

Unpacking Your Fireplace

Parts and Hardware
Tools Required

• Phillips-head screwdriver
• Stud finder
• Level
• Tape measure
• Electric drill
• 1/4” wood drill bit

What’s in the Box

Unpacking and Setup
Unpacking Instructions :

•  Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Check the parts list to make sure no parts are missing. If parts are missing, please contact technical support at 800-215-1990 opt 2. for replacement parts.
  NOTE: Dispose of plastic bag, as it may cause choking hazard with young children. Do not let children play with plastic bag.

Wiring
Touchstone Wall Mounted Electric Fireplaces come with a 3-prong plug which plugs into any standard 110v outlet.
Testing the Fireplace Prior to Installation

• Before installing the fireplace, test the fireplace to make sure that it operates properly.
  • Plug fireplace into approved outlet and power on fireplace. Once fireplace is tested, continue with installation.

• If you have any problems, please contact technical support at 800-215-1990 opt 2.

3- prong Outlet Installation

• Only use this fireplace on a 120V AC, 15-Amp grounded circuit. Never overload the circuit. If this fireplace trips the circuit breaker, unplug all other appliances on the same circuit before the next use. Avoid plugging other appliances into the same circuit as this fireplace.
• Always check the fireplace plug and connections before each use.
• Never plug this fireplace into an outlet that is cracked or has any loose wires or connections. Plugging this fireplace into a faulty outlet could result in the outlet overheating or catching fire.
• Make sure this plug fits securely into the outlet. Faulty wall outlet connections or loose plugs can cause the outlet to overheat. If the outlet or faceplate is hot, discontinue use immediately and have a qualified electrician inspect and/or replace the faulty outlet.
• The power cord supplied with the heater has three prongs: two flat blades (live and neutral) and one round pin (ground). If a 3-slot receptacle is not available, an adapter MUST be used. The adapter MUST be properly grounded to the outlet box (see figure below).

Hard Wire Connection
If it is necessary to hard wire this appliance, a qualified electrician must remove the cord connection, and wire the appliance directly to the house hold wiring.
This appliance must be electrically connected and grounded in accordance with local codes, if hard wired. In the absence of local codes, use the current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States or the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada.

A. Remove the cover plate from the right side bottom of the appliance by removing the three screws, as shown above. Save screws for Installation of new cover plate.
B. Remove the wire connectors from the power cord. Keep power cord, in case needed in future.
C. Remove the power cable and wires from the cover plate. Thread your wiring through the hole in the cover plate for connecting to the wires in the Sideline® Elite fireplace.
D. Using the wire connectors, connect the ground green wires (G), the common white wires (N) together, and then the hot black wires (L) Refer to Figure 3 when complete.
E. Reinstall the cover plate using the three screws, as shown in Figure 1.

Installation

WARNINGS

• Due to high temperatures, keep the fireplace out of high traffic locations.
• Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 36” away from the front of the fireplace.
• Never install the fireplace where it may fall into a bathtub or other body of water.
• Wear safety gloves and safety glasses for protection during installation. Broken glass may cause injury or harm.
• Prevent contact with loose insulation. Do not install the fireplace against a vapor barrier or exposed insulation.
• Do not expose the fireplace to the elements (rain, etc).

Choosing Installation Location
Choosing Wall Location

• Measure wall location to ensure that fireplace will fit on desired wall location.
• Minimum clearances (measurements taken from front of glass panel):

• Select a location that is not prone to moisture and is located at least 36” away from combustible materials such as curtains, drapes, furniture, bedding, or other combustible materials.
• See Safety Information on pages 3 for warnings about safe placement, safe installation, and proper use of this product.

Removing The Wall Mount Bracket From Fireplace
Tools:

– Phillips-head screw driver
Instructions:

1. Remove the fireplace from the packaging and place it on a flat, non-abrasive surface.

2. Remove the wall mount bracket from the back of the fireplace. To remove the bracket, use a Philips-head screwdriver to remove the 4 screws numbered 1-4 in the illustration shown below:
   

3.  Place the mounting bracket and screws off to the side for mounting to the wall. Wall mounting instructions are located on p.13 of this manual.

Removing The Glass Panel and Install Media
Prior to installation on the wall, it is best to remove the glass panel. Please remove glass panel as per instructions below:
Tools Needed:
– Phillips Screwdriver
Instructions:

1. Locate the 4 screws securing the front glass panel to the fireplace. The screws are located on the underside of the top portion of the mantel.

2.  Loosen and remove the 4 screws holding the glass panel to the fireplace and remove the glass panel. Save the 4 screws in a safe spot for reinstallation later.

NOTE: Hold the glass panel in place when removing the last screw so that the glass panel does not fall.
Removing The Glass Panel and Install Media – cont.

3. Install the crystal glass and/or driftwood media.

4. Once the crystal glass and/or driftwood media is installed, reinstall the glass panel using the 4 screws removed in step 2.

5. Once the glass panel is installed, the fireplace is ready to be mounted.

Wall Mounted Installation

• Due to many different finish materials used on walls, it is highly recommended that you consult your local builder before you install this fireplace on the wall.
• Select a location that is not prone to moisture and is located at least 36” away from combustible materials such as curtains, drapes, furniture, bedding, or other combustible materials.

Instructions

1. Select a location that is not prone to moisture and is located at least 36” away from combustible materials, such as curtains, drapes, furniture, bedding, paper, etc.
2. With glass panel removed (see p.11 for instructions on removing glass panel), have two people hold the fireplace against the wall to determine the final location.
3.  Place the unit face down on a soft, non-abrasive surface. Locate the mounting bracket that was removed on p.10.
4. Locate the wall studs using an electronic stud-finder. When hanging the wall bracket, it is recommended to fasten the mounting bracket to 3 studs. If fastening to 3 studs, no dry anchors would need to be used. If fastening to only 2 studs, then dry wall anchors would need to be used to fasten the mounting bracket to the wall. Make mark
   on the wall at least 24” above the ground.

Note: The minimum height from the bottom of the fireplace, once hung on the wall, to the surface below must be at least 6”. To meet this criteria, the wall mount bracket should be hung no lower than 24” from the ground to the top of the mounting bracket when hung on the wall.
Wall Mounted Installation – cont.

5. Align the mounting bracket with the mark on the wall and mark the location of the mounting holes on the wall, making sure to line up with at least 2 studs. It is recommended to fasten the mounting bracket to 3 studs, if possible.

6. Attach the mounting bracket to the wall using the screws provided. If fastening to 3 studs, no dry anchors would need to be used. If fastening to only 2 studs, then at least 2 dry wall anchors would need to be used to fasten the mounting bracket to the wall.

7. Once the bracket is secured to the wall, the fireplace may now be hung on the bracket.
8. Once the fireplace is mounted on the bracket, install the locking screws to secure the bracket to the fireplace mantel.

Operating Fireplace

Once the fireplace has been plugged into a grounded outlet, the fireplace is now ready for operation. Ensure that the house circuit breakers for the power supply are turned on.
Methods of Operation
This electric fireplace can be operated by the CONTROL PANEL, located in the upper right corner of the front glass panel, or by the REMOTE CONTROL. The operation and functions of both methods are the same

Control Panel and Remote Control Functions

flame effect.
OFF : Disables control panel functions and remove control. Turns off the flame effect.| 1.  Press once. Indicator light turns on. Power turns on. All functions enabled.
2.  Press again. Flame effect turns off. Unit goes to standby. All functions turn off.
| TIMER button : Control time settings to turn off fireplace at selected time.
Settings range from 0.5 hours to 7.5 hours.| 1.  Press once. Indicator light turns on. Timer is set to 0.5 hours.
2.  Press again until desired setting is reached. Indicator lights show setting.
| FLAME button: Makes flame effect dimmer and brighter.
NOTE : Flame effect stays on until power button is turned off. Flame effect must be on for heater to turn on.| 1.  Press once : Each press of the flame button changes the flame brightness.
2.  Press again until desired setting is reached. Flame effect continues to get brighter each time button is pressed.
| COLOR button : Changes color of the flame
NOTE : Color effect stays on until power button is turned off. Flame effect must be on for heater to turn on.| 1.  Press once : Flame effect changes color.
2.  Press again until desired setting is reached. 3 total colors (orange, blue, and blue/orange).
| HEATER button : Turns heater on and off.
NOTE : The heater only works when the flame effect is on.
NOTE : To prevent overheating, the heater fan will blow cool air for 8-10 seconds before the heater turns on, and after the heater turns off.| 1. Press once. Indicator lights up. Fan blows cool air for 10 seconds and 750W heater turns on and blows warm air.
2.  Press again : Indicator lights up. 1500W heater turns on and blows hot air.
3.  Press again. Heater turns off.
| 1.  Press once: Touch panel indicator becomes active.
2.  Press again until desired setting is reached. Digital display shows setting below| Display value| 0| 1| 2| 3| 4| 5| 6| 7| 8| 9| 10
---|---|---|---|---|---|---|---|---|---|---|---
Temperature| °C| 20| 21| 22| 23| 24| 25| 26| 27| 28| 29| 30
°F| 68| 70| 72| 74| 76| 78| 80| 82| 84| 86| 88

NOTE: Press the button for 5 seconds to switch between °C and °F

Remote Control Operation

• This remote control uses two AAA batteries (Not included).
• Instructions for battery installation are located in the remote control battery compartment.
• To improve operation of the remote control, aim the remote control at the front of the fireplace. DO NOT PRESS the buttons too quickly. Give the unit time to respond to each command.
• NOTICE: NEVER dispose of batteries in fire. Failure to observe this precaution may result in an explosion. Dispose of batteries at your local hazardous material processing center.

Temperature Limiting Control
This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafe temperature, the heater will automatically TURN OFF. To reset, please do the following:

1. Unplug the power cord from the outlet.
2. Turn ON/OFF switch on the CONTROL PANEL to OFF. Wait 5 minutes for fireplace to cool down.
3. Inspect the fireplace to make sure no vents are blocked or clogged with dust or lint. If they are, use a vacuum to clean the vent areas.
4. With the POWER switch in the OFF position, plug the power cord back into the outlet.
5. If the problem continues, have your outlet and wiring inspected by a professional. If the outlet is OK, please contact our customer support department at 800-215-1990.

Care and Maintenance

Cleaning

• ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving the fireplace. Failure to do so could result in electric shock, fire, or personal injury.
• NEVER immerse in water or spray with water. Doing so could result in electric shock, fire, or personal injury. Metal:
• Buff using a soft cloth, slightly dampened with citrus oil-based product.
• DO NOT use brass polish or household cleaners, as these products will damage the metal trim.

Glass:

• Use a good quality glass cleaner sprayed onto a cloth or towel. Dry thoroughly with a paper towel or lint- free cloth.
• NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.

Vents:

• Use a vacuum or duster to remove dust and dirt from the heater and vent areas.

Plastic:

• Wipe gently with a slightly damp cloth and a mild solution of dish soap and warm water.
• NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.

Maintenance

• RISK OF ELECTRIC SHOCK! DO NOT OPEN any panels. No user-serviceable parts inside!
• ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving the fireplace. Failure to do so could result in electric shock, fire, or personal injury.

Electrical and Moving Parts:

• The fan motors are lubricated at the factory and will not require lubrication.
• Electrical components are integrated in the fireplace and are not serviceable by the customer.

Storage:

• Store fireplace in a clean, dry place when not in use.

Warranty

Touchstone Home Products Limited Warranty
Touchstone Home Products®, Inc offers a one (1) year limited warranty on all our electric fireplaces. The one (1) year warranty starts on the date of purchase and expires 1 calendar year from the original date of purchase.
Electrical components, such as fan motor, heater motor, control board, remote control, LED lights and control panel are covered under warranty for one year from date of purchase. Touchstone Home Products® will provide replacement parts free of charge during the first year of the warranty.
Touchstone Home Products® will not be responsible for installation, labor, or any other expenses related to the reinstallation of a warranted part, and such expenses are not covered under warranty.

Conditions and Limitations
Touchstone Home Products®, Inc warrants our electric fireplaces to be free of defects in material and workmanship to the original purchaser only. Registering your warranty is not necessary. Just provide your proof of purchase along with the model fireplace to make a warranty claim.
Warranty coverage begins on the date of purchase.
The factory warranty is non-transferrable.
Touchstone Home Products®, Inc does not cover damages caused by abuse, accident, alterations, lack of maintenance, misuse, or neglect. Parts installed from other manufacturers will void the warranty.
Touchstone will repair or replace any fireplace or fireplace part that is deemed defective or becomes defective during normal use within one (1) year after the date of purchase.
Replacement parts and replacement fireplace units are covered under a 90-day warranty or the remainder of the original one (1) year manufacturer’s warranty from original date of purchase, whichever is greater.
Touchstone Home Products®, Inc does not warrant its products against damage caused by third parties.
The warranty does not cover paint scratches, cosmetic blemishes, dents, corrosion, or other normal wear and tear associated with the fireplace. Damage to fireplace or other components due to water, weather damage, long periods of dampness, condensation, damaging chemicals or cleaners are not covered under warranty.
Touchstone Home Products®, Inc limited warranty does not cover accidental breakage of fireplace glass panel.
Extended warranty coverage for the fireplace is available by contacting Touchstone Home Products® directly at 1- 800-215-1990.

CALL US FIRST! DO NOT RETURN TO STORE.
For immediate help with assembly,product information, or if your product arrives damaged,call our toll-free number at 800-215-1990
or email:
customerservice@thpus.com
Our staff is ready to provide assistance.

Affix Serial Number Label Here

www.touchstonehomeproducts.com
800.215.1990
Rev. 200123

Documents / Resources

| touchstone 80033 Chesmont Series Electric Fireplace [pdf] Owner's Manual
80033, 80034, 80033 Chesmont Series Electric Fireplace, Chesmont Series, Electric Fireplace, Chesmont Series Electric Fireplace, Fireplace
---|---

References

• Touchstone Home Products Electric Fireplaces, TV Lifts, and Cabinets – Touchstone Home Products, Inc.
• Touchstone Home Products Electric Fireplaces, TV Lifts, and Cabinets – Touchstone Home Products, Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>