Honeywell PRO 1000 Series Non-Programmable Thermostat Instruction Manual
- June 9, 2024
- Honeywell
Table of Contents
PRO 1000 Series
Non-Programmable Thermostat
Operating Manual
PRO 1000 Series Non-Programmable Thermostat
This manual covers the following models:
TH1100DV: For 1 Heat systems
TH1110DV: For 1 Heat/1 Cool systems
TH1210DV: For 2 Heat/1 Cool heat pump systems
(Pull thermostat from wallplate and turn over to find model number.)
CAUTION: EQUIPMENT DAMAGE HAZARD.
To prevent possible compressor damage, do not operate cooling system when
outdoor temperature is below 50°F (10°C).
Need Help?
For assistance with this product please visit
Honeywellhome.com/support Read before
installing.
® U.S. Registered Trademark. Patents pending.
Copyright © 2020 Resideo Technologies Inc. All rights reserved.
About your new thermostat
Your new Resideo thermostat has been designed to give you many years of reliable service and easy-to-use, push-button climate control.
Features
- Backlit display is easy to read
- Displays ambient (measured) temperature at all times
- One-touch access to setpoint temperature
- Built-in compressor protection
Quick reference to controls
Quick reference to display screen
When “Heat On” or “Cool On” is flashing, compressor protection is engaged (see page 8).
Select the system setting
The SYSTEM switch can be set to control your heating or cooling system, depending on the season.
- Cool: Cooling system control.
- Off: All systems are off.
- Heat: Heating system control.
- Em Heat: Emergency & Auxiliary Heat control. Compressor is locked out. (Select models only.)
CAUTION: EQUIPMENT DAMAGE HAZARD. To prevent possible compressor damage, do not operate cooling system when outdoor temperature is below 50°F (10°C).
Select the fan setting
Set the FAN switch to Auto or On.
In “Auto” mode (the most commonly used setting), the fan runs only when the
heating or cooling system is on. If set to “On,” the fan runs continuously.
Adjust the temperature
Note: Make sure the thermostat is set to the system you want to control (heat or cool).
Built-in compressor protection
This feature helps prevent damage to the compressor in your air conditioning
or heat pump system.
Damage can occur if the compressor is restarted too soon after shutdown. This
fea- ture forces the compressor to wait 5 minutes before restarting.
During the wait time, the display will flash the message Cool On (or Heat On
if you have a heat pump model). When the safe wait time has elapsed, the
message stops flashing and the compressor turns on.
Battery replacement
Pull at bottom to remove thermostat from wallplate.
Turn thermostat over, insert fresh AAA alkaline batteries, then reinstall
thermostat.
Install two fresh AAA batteries when Lo Batt flashes on the screen. Lo Batt
appears for 60 days before the batteries are depleted. Replace batteries once
a year, or when you will be away for more than a month. The settings are
stored in non-volatile (permanent) memory and are thus preserved when the
thermostat is without batteries.
Customer assistance
Pull at bottom to remove thermostat from wallplate.
Turn thermostat over to find model number and date code.
For assistance with this product, please visit
Honeywellhome.com/support.
On Fan Auto To save time, please note your model number and date code before
calling.
In case of difficulty
If you have difficulty with your thermostat, please try the following
suggestions.
Most problems can be corrected quickly and easily.
Display is blank| • Check circuit breaker and reset if necessary.
• Make sure power switch at heating & cooling system is on.
• Make sure furnace door is closed securely.
• Make sure fresh AAA alkaline batteries are correctly installed
(see page 9).
---|---
Heating or cooling system does not respond| • Set system switch to Heat (see
page 5). Make sure the
temperature is set higher than the Inside temperature.
• Set system switch to Cool (see page 5). Make sure the
temperature is set lower than the Inside temperature.
• Wait 5 minutes for the system to respond.
Temperature settings do not
change| Make sure heating and cooling temperatures are set to acceptable
ranges:
• Heat: 40° to 90°F (4.5° to 32°C).
• Cool: 50° to 99°F (10° to 37°C).
“Heat On” or “Cool On” is
flashing| • Compressor protection feature is engaged. Wait 5 minutes for the
system to restart safely, without damage to the compressor (see page 8).
“Heat On” is not displayed| • Set the System switch to Heat, and set the
temperature level above the current room temperature (see page 5).
“Cool On” is not displayed| • Set the System switch to Cool, and set the
temperature level below the current room temperature (see page 5).
2-year limited warranty
For warranty information go to Honeywellhome.com/support
CAUTION: MERCURY NOTICE.
If this product is replacing a control that contains mercury in a sealed tube,
do not place the old control in the trash. Contact your local waste management
authority for
instructions regarding recycling and proper disposal.
CAUTION: ELECTRONIC WASTE NOTICE.
The product should not be disposed of with other household waste. Check for
the nearest authorized collection centers or authorized recyclers. The correct
disposal of end-of-life equipment will help prevent negative consequences for
the environment and human health.
FCC statement at:
https://customer.resideo.com/en-US/support/residential/codes-and-standards/
FCC15105/Pages/default.aspx
Resideo Technologies Inc.
1985 Douglas Drive North, Golden Valley, MN 55422
https://www.honeywellhome.com/support
69-2798EFS—03 M.S. Rev. 08-20 | Printed in United States
© 2020 Resideo Technologies, Inc. All rights reserved. The Honeywell Home
trademark is used under license from Honeywell International, Inc. This
product is manufactured by Resideo Technologies, Inc. and its affiliates.
Documents / Resources
|
Honeywell PRO 1000 Series Non-Programmable
Thermostat
[pdf] Instruction Manual
PRO 1000 Series Non-Programmable Thermostat, PRO 1000 Series, Non-Programmable
Thermostat, Programmable Thermostat, Thermostat
---|---
References
- Product Support and Resources | Honeywell Home
- Smart Home Solutions in EMEA | Resideo
- Codes and Standards
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>