Keychron M3 Wireless Mouse User Manual
- June 9, 2024
- Keychron
Table of Contents
Keychron M3 Wireless Mouse User Manual
- Left button
- Right button
- Middle wheel button
- Forward button
- Backward button
- RGB light effects button
- DPl button
- Modes toggle
- 2.4GHz Type – C receiver
- Report rate button
- 2.4GHz Type-A receiver
3 Modes of connection
Wired Mode:
- When the mode switch is in “OFF” position, the mouse won’t respond if the cable is not connected.
- Connect the cable to the TYPE-C port of the mouse and the USB port on the device. The mouse is ready to use while the backlit lights up.
- When connected by cable, the mode will default to wired mode even if the toggle is in Bluetooth mode or2.4GHz mode.
2.4GHz Mode:
- Switch to “G” mode (2.4GHz mode), and the mouse will automatically turn on 2.4GHz paring. The RGB light on the mouse wheel will slowly flash green.
- Find the 2.4GHz receiver and connect it to the device’s USB/Type-C port. Once successfully connected, the RGB light on the mouse wheel will turn green and stay on for 3 seconds, then dims off. The RGB backlit enters breathing mode when successfully connected.
- In 2.4GHz paring mode, the RGB light on the side of the mouse wheel will slowly blink green for 3 minutes. If it’s not connected within 3 minutes, the RGB light on the mouse wheel will turn off. If you need to reconnect, hold both the “Left button+ RGB light effects button” for4seconds to re-enter pairing mode.
- If you need to repair the connection in 2.4GHz mode, please unplugthe2.4GHz receiver first. Then, hold both the “Left button+ RGB light effects button” for4 seconds, wait for the green light indicator to start flashing, and plug the 2.4GHz receiver back in to complete the pairing process.
Note: It is recommended that when pairing the M3 in 2.4GHz mode, the mouse should be within 20cm of the receiver.
Bluetooth mode
- Switch to “B” Mode (Bluetooth), and the mouse will automatically turn on Bluetooth pairing mode. The RGB light on the side of the mouse wheel will slowly flash blue.
- Open the Bluetooth settings, search for a device named “Key chron M3”, then click “connect” to complete paring.
- When in Bluetooth pairing mode, the RGB light on the side of the wheel will slowly blink in blue for 3 minutes. If it’s not connected within 3 minutes, the RGB light on the mouse wheel will turn off. If you need to reconnect, you need to hold the “Left button+ RGB light effects button” for4 seconds to re-enter pairing mode. The mode indicator will slowly blink blue.
- lf the M3 is in Bluetooth mode and needs to pair with a new device, hold both the “Left button+ RGB light effects button” for 4 seconds and wait for the blue light to flash on, At this point, Bluetooth has re-entered pairing mode, and you can connect the new device to the M3.
Status indicator
DPI indicator
Report Rate indicator
How to factory reset
Hold down both the “DPI button” and “Report rate button” for4seconds, and all the LED lights on the mouse will blink. It will blink three times to indicate that the factory reset is successful.
simultaneously hold for4 seconds (starts factory reset)
Auto-Sleep mode
Auto-Sleep mode will not be activated when in wired mode. When in 2.4GHz mode or Bluetooth mode, the mouse will go to Auto-Sleep mode after 15 minutes of sitting idle to save the battery. Move or click the mouse to wake it up.
Driver Software
The Keychron M3 mouse driver can be downloaded from www.keychron.com. If the driver software can’t connect to the mouse, please contact us for technical support.
Charging indicator explanation
- The mouse is compatible with all USB ports. For the best signal and charging speed, connecting to the USB3.0 port is recommended when charging or in use.
- The mouse can be charged in 2.4GHz mode, Bluetooth mode and wired mode.
- If the mouse is connected by the USB Type – C cable when charging but not paired with any devices:
- The RGB backlit on the side of the mouse wheel will blink RED for 10s, then dim off when charging.
- The RGB backlit on the side of the mouse wheel will blink GREEN for 5s, then dim off when fully charged.
Note: The product supports up to SV charging voltage and 300 mA charging current. We are not responsible for any problems caused by improper recharging.
What’s in the box
Mouse x 1 USB
Type-C receiver x 1
Extension Adapter x 1
User manaual x 1
USB Type – C to Type – C cable x 1
USB Type -A receiver x 1
USB Type -A to USB – C adapter x 1
Mouse specification
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirement in portable exposure condition without restriction.
Keychron, Inc.
Dover, DE 19901, United States
Find us at:
https://www.keychron.com
Support@keychron.com
Designed by Keychron
Made in China